Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485736 PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park)  C169D87  Side Camera (Right) Image Signal Missing Message  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly RH to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C169D87 Side Camera (Right) Image Signal Missing Message Side camera feedback malfunction (Right)
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH

·

Outer rear view mirror assembly RH (television camera wire RH)


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E444531E02
5.729,2.5 6.188,2.698 0.458,0.198 10 false O121 5.74,2.667 7,3.115 1.26,0.448 10 false Parking Assist ECU 2.01,2.563 4.313,2.99 2.302,0.427 10 false Outer Rear View Mirror Assembly RH (Television Camera Wire RH) 2.021,2.396 3.24,2.594 1.219,0.198 10 false KK1 0.375,2.385 1.5,2.583 1.125,0.198 10 false K15 0.375,2.563 1.833,2.938 1.458,0.375 10 false Side Television Camera Assembly RH 2.865,0.271 3.479,0.469 0.615,0.198 10 false RCB+ 2.865,0.656 3.479,0.854 0.615,0.198 10 false RCV+ 2.896,1.063 3.51,1.26 0.615,0.198 10 false RCV- 2.854,1.5 3.469,1.698 0.615,0.198 10 false RGND 2.854,1.896 3.469,2.094 0.615,0.198 10 false SGND 6.01,2.021 6.625,2.219 0.615,0.198 10 false SGND 6.021,1.635 6.635,1.833 0.615,0.198 10 false RGND 6.01,1.198 6.625,1.396 0.615,0.198 10 false RCV- 6.01,0.792 6.625,0.99 0.615,0.198 10 false RCV+ 6.01,0.406 6.625,0.604 0.615,0.198 10 false RCB+ 3.375,0.271 3.531,0.469 0.156,0.198 10 false 2 3.375,1.063 3.552,1.26 0.177,0.198 10 false 3 3.375,0.667 3.552,0.865 0.177,0.198 10 false 4 3.375,1.5 3.552,1.698 0.177,0.198 10 false 1 3.385,1.885 3.563,2.083 0.177,0.198 10 false 5 5.781,1.844 6.104,2.094 0.323,0.25 10 false 5 5.771,1.031 6.094,1.281 0.323,0.25 10 false 3 5.76,1.479 6.083,1.729 0.323,0.25 10 false 1 5.771,0.656 6.094,0.906 0.323,0.25 10 false 4 5.771,0.25 6.094,0.5 0.323,0.25 10 false 2 1.958,0.281 2.135,0.479 0.177,0.198 10 false 2 1.958,0.667 2.135,0.865 0.177,0.198 10 false 1 1.948,1.073 2.125,1.271 0.177,0.198 10 false 3 1.948,1.5 2.125,1.698 0.177,0.198 10 false 4 1.948,1.885 2.125,2.083 0.177,0.198 10 false 5 4.625,2 4.802,2.198 0.177,0.198 10 false * 0.177,3.438 2.927,3.635 2.75,0.198 10 false *: Shielded 1.406,2.031 2.021,2.229 0.615,0.198 10 false SGND 1.5,1.625 2.115,1.823 0.615,0.198 10 false GND 1.5,0.781 2.115,0.979 0.615,0.198 10 false CV+ 1.5,0.385 2.115,0.583 0.615,0.198 10 false CB+ 1.531,1.177 2.146,1.375 0.615,0.198 10 false CV-

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH))

Pre-procedure1

a.

Disconnect the O121 parking assist ECU connector.


b.

Disconnect the KK1 outer rear view mirror assembly RH (television camera wire RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
T ester Connection Condition Specified Condition
O121-2 (RCB+) - KK1-2 (RCB+) Always Below 1 Ω
O121-4 (RCV+) - KK1-4 (RCV+) Always Below 1 Ω
O121-3 (RCV-) - KK1-3 (RCV-) Always Below 1 Ω
O121-1 (RGND) - KK1-1 (RGND) Always Below 1 Ω
O121-5 (SGND) - KK1-5 (SGND) Always Below 1 Ω
O121-2 (RCB+) or KK1-2 (RCB+) - Body ground Always 10 kΩ or higher
O121-4 (RCV+) or KK1-4 (RCV+) - Body ground Always 10 kΩ or higher
O121-3 (RCV-) or KK1-3 (RCV-) - Body ground Always 10 kΩ or higher
O121-1 (RGND) or KK1-1 (RGND) - Body ground Always 10 kΩ or higher
O121-5 (SGND) or KK1-5 (SGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (RCV-, RGND)

Pre-procedure1

a.
E394298C05
0.167,0.979 0.708,1.26 0.542,0.281 1.979,0.896 2.531,0.542 true 1.969,1.115 2.552,1.333 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.635,0.448 3.083,0.646 0.448,0.198 10 false RGND 2.635,1.26 3.083,1.458 0.448,0.198 10 false RCV- 0.26,1.031 0.708,1.229 0.448,0.198 10 false O121
*a Component without harness connected
(Parking Assist ECU)


Disconnect the O121 parking assist ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O121)Location & Routing

Click Connector(O121)Body>Floor Wire>Parking Assist ECU

O121-1 (RGND) - Body ground Always Below 1 Ω
O121-3 (RCV-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

3.CHECK PARKING ASSIST ECU (RCB+, RGND)

Pre-procedure1

a.

Disconnect the KK1 outer rear view mirror assembly RH (television camera wire RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(KK1)Location & Routing

Click Connector(KK1)Body>Front Door Wire RH / Television Camera Wire>Television Camera Wire and Front Door Wire RH

KK1-1 (RGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(KK1)Location & Routing

Click Connector(KK1)Body>Front Door Wire RH / Television Camera Wire>Television Camera Wire and Front Door Wire RH

KK1-2 (RCB+) - KK1-1 (RGND) Ignition switch ON 7 to 8 V
KK1-2 (RCB+) - KK1-1 (RGND) Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH)

NG

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH)

Pre-procedure1

a.
E434382C45
1.5,1.948 1.906,2.177 0.406,0.229 1.5,0.115 2,0.365 0.5,0.25 0.938,3.313 1.625,2.99 true 2.427,3.406 1.771,3.167 true 2.396,3.198 1.802,2.99 true 2.385,2.427 1.802,2.802 true 0.917,2.396 1.615,2.792 true 2.469,1.708 1.781,1.302 true 2.438,1.469 1.896,1.125 true 2.448,0.573 1.854,0.969 true 0.896,0.573 1.594,0.969 true 0.885,1.469 1.552,1.135 true 0.094,0.177 0.406,0.375 0.313,0.198 10 false *a 1.583,1.979 1.896,2.177 0.313,0.198 10 false K15 0.146,2.01 0.458,2.208 0.313,0.198 10 false *b 2.552,0.5 3.167,0.698 0.615,0.198 10 false RCB+ 0.469,1.417 1.083,1.615 0.615,0.198 10 false RCV- 2.552,1.417 3.167,1.615 0.615,0.198 10 false RCV+ 0.469,0.5 1.083,0.698 0.615,0.198 10 false RGND 2.552,1.667 3.167,1.865 0.615,0.198 10 false SGND 0.604,3.25 1.219,3.448 0.615,0.198 10 false CV- 2.479,3.125 3.094,3.323 0.615,0.198 10 false GND 2.469,2.333 3.083,2.531 0.615,0.198 10 false CB+ 0.552,2.313 1.167,2.51 0.615,0.198 10 false CV+ 2.5,3.365 3.115,3.563 0.615,0.198 10 false SGND 1.625,0.156 1.948,0.365 0.323,0.208 10 false KK1
*a Component without harness connected
(Outer Rear View Mirror Assembly RH (television camera wire RH))
*b Front view of wire harness connector
(to Side Television Camera Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH (television camera wire RH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(KK1,K15)Location & Routing

Click Connector(KK1)Body>Front Door Wire RH / Television Camera Wire>Television Camera Wire and Front Door Wire RH

Click Connector(K15)Body>Front Door Wire RH / Television Camera Wire>Side Television Camera Assembly RH

KK1-2 (RCB+) - K15-2 (CB+) Always Below 1 Ω
KK1-4 (RCV+) - K15-1 (CV+) Always Below 1 Ω
KK1-3 (RCV-) - K15-3 (CV-) Always Below 1 Ω
KK1-1 (RGND) - K15-4 (GND) Always Below 1 Ω
KK1-5 (SGND) - K15-5 (SGND) Always Below 1 Ω
KK1-2 (RCB+) or K15-2 (CB+) - Body ground Always 10 kΩ or higher
KK1-4 (RCV+) or K15-1 (CV+) - Body ground Always 10 kΩ or higher
KK1-3 (RCV-) or K15-3 (CV-) - Body ground Always 10 kΩ or higher
KK1-1 (RGND) or K15-4 (GND) - Body ground Always 10 kΩ or higher
KK1-5 (SGND) or K15-5 (SGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH)

5.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 470

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470

Result:
Result Proceed to
C169D87 is not output A
C169D87 is output B



A

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

B