Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485736 PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park)  Image from Camera for Panoramic View Monitor is Abnormal  


DESCRIPTION

The display signal from each television camera is transmitted to the radio and display receiver assembly via the parking assist ECU.

WIRING DIAGRAM

E465908E01
1.365,7.25 1.844,7.448 0.479,0.198 10 false CGND 1.375,7.729 1.875,7.927 0.5,0.198 10 false SGND 1.375,4.698 1.99,4.896 0.615,0.198 10 false SGND 0.219,5.167 2.49,5.448 2.271,0.281 10 false Front Television Camera Assembly 5.417,8.188 6.656,8.396 1.24,0.208 10 false Parking Assist ECU 1.906,0.208 2.208,0.438 0.302,0.229 10 false 28 1.917,0.708 2.146,0.906 0.229,0.198 10 false 29 1.917,1.219 2.115,1.427 0.198,0.208 10 false 27 0.323,7.969 0.615,8.146 0.292,0.177 10 false Y35 1.51,6.76 1.813,6.948 0.302,0.188 10 false CV- 1.479,6.26 1.833,6.438 0.354,0.177 10 false CV+ 1.469,5.75 1.833,5.948 0.365,0.198 10 false CB+ 5.635,5.74 5.969,5.927 0.333,0.188 10 false CB+ 5.635,6.26 5.969,6.458 0.333,0.198 10 false CV+ 5.635,6.771 5.948,6.99 0.313,0.219 10 false CV- 5.625,7.24 6.094,7.427 0.469,0.188 10 false CGND 1.896,3.125 2.271,3.302 0.375,0.177 10 false 4 1.896,2.635 2.271,2.813 0.375,0.177 10 false 2 1.896,3.646 2.271,3.823 0.375,0.177 10 false 3 0.219,4.979 0.51,5.167 0.292,0.188 10 false B18 1.344,4.219 1.958,4.417 0.615,0.198 10 false BGND 1.375,3.708 1.99,3.906 0.615,0.198 10 false BCV- 1.365,3.219 1.979,3.417 0.615,0.198 10 false BCV+ 1.365,2.729 1.979,2.927 0.615,0.198 10 false BCB+ 1.896,4.625 2.219,4.802 0.323,0.177 10 false 5 1.896,4.146 2.219,4.323 0.323,0.177 10 false 1 5.229,2.49 5.615,2.656 0.385,0.167 10 false 2 5.24,2.99 5.573,3.167 0.333,0.177 10 false 4 3.385,7.76 3.542,7.958 0.156,0.198 10 false * 5.208,0.115 5.594,0.333 0.385,0.219 10 false 12 5.208,0.604 5.417,0.771 0.208,0.167 10 false 11 5.208,1.104 5.385,1.302 0.177,0.198 10 false 13 5.625,1.854 6.115,2.052 0.49,0.198 10 false RSW+ 5.104,0.354 5.521,0.542 0.417,0.188 10 false O118 1.542,0.354 1.99,0.542 0.448,0.188 10 false V+ 1.563,0.823 1.958,1 0.396,0.177 10 false V- 1.354,1.344 1.792,1.542 0.438,0.198 10 false CGND 0.313,8.135 2.458,8.354 2.146,0.219 10 false Rear Television Camera Assembly 5.625,2.719 6.063,2.917 0.438,0.198 10 false BCB+ 5.625,3.219 6.063,3.417 0.438,0.198 10 false BCV+ 5.635,3.729 6.042,3.927 0.406,0.198 10 false BCV- 5.635,4.25 6.125,4.448 0.49,0.198 10 false BGND 5.25,3.5 5.583,3.677 0.333,0.177 10 false 3 5.229,4 5.563,4.177 0.333,0.177 10 false 1 5.24,4.49 5.573,4.667 0.333,0.177 10 false 5 3.375,4.781 3.531,4.979 0.156,0.198 10 false * 3.385,1.313 3.542,1.51 0.156,0.198 10 false * 5.229,5.49 5.656,5.667 0.427,0.177 10 false 2 5.229,6.01 5.604,6.188 0.375,0.177 10 false 4 5.24,6.51 5.615,6.688 0.375,0.177 10 false 3 5.229,7 5.552,7.177 0.323,0.177 10 false 1 5.24,7.49 5.563,7.667 0.323,0.177 10 false 5 5.625,7.729 6.083,7.917 0.458,0.188 10 false SGND 0.188,8.531 1.104,8.719 0.917,0.188 10 false *: Shielded 5.625,4.719 6.094,4.917 0.469,0.198 10 false SGND 0.229,2.292 2.896,2.615 2.667,0.323 10 false Radio and Display Receiver Assembly 1.323,1.844 1.792,2.031 0.469,0.188 10 false CSW+ 5.25,1.615 5.49,1.781 0.24,0.167 10 false 5 1.906,1.719 2.208,1.948 0.302,0.229 10 false 18 0.219,2.115 0.531,2.281 0.313,0.167 10 false H80 5.115,0.833 5.531,1.021 0.417,0.188 10 false O118 5.115,1.344 5.531,1.531 0.417,0.188 10 false O118 5.115,1.854 5.531,2.042 0.417,0.188 10 false O118 5.625,1.344 6.063,1.542 0.438,0.198 10 false NSG 5.625,0.354 6.073,0.542 0.448,0.188 10 false NS+ 5.625,0.833 6.073,1.021 0.448,0.188 10 false NS- 1.896,5.625 2.271,5.802 0.375,0.177 10 false 2 1.906,6.135 2.281,6.313 0.375,0.177 10 false 4 1.906,6.646 2.281,6.823 0.375,0.177 10 false 3 1.906,7.115 2.229,7.292 0.323,0.177 10 false 1 1.917,7.594 2.24,7.771 0.323,0.177 10 false 5 5.104,2.729 5.521,2.917 0.417,0.188 10 false O120 5.125,3.219 5.542,3.406 0.417,0.188 10 false O120 5.115,3.74 5.531,3.927 0.417,0.188 10 false O120 5.115,4.24 5.531,4.427 0.417,0.188 10 false O120 5.125,4.719 5.542,4.906 0.417,0.188 10 false O120 5.125,5.75 5.542,5.938 0.417,0.188 10 false O123 5.135,6.26 5.552,6.448 0.417,0.188 10 false O123 5.125,6.76 5.542,6.948 0.417,0.188 10 false O123 5.115,7.24 5.531,7.427 0.417,0.188 10 false O123 5.125,7.729 5.542,7.917 0.417,0.188 10 false O123

E444533E02
5.448,0.76 6.063,0.958 0.615,0.198 10 false O122 5.979,0.771 6.594,0.969 0.615,0.198 10 false LCB+ 5.979,1.281 6.594,1.479 0.615,0.198 10 false LCV+ 5.99,1.792 6.604,1.99 0.615,0.198 10 false LCV- 5.99,2.302 6.604,2.5 0.615,0.198 10 false LGND 5.979,2.802 6.594,3 0.615,0.198 10 false SGND 5.583,0.51 6.198,0.708 0.615,0.198 10 false 2 5.583,1.021 6.198,1.219 0.615,0.198 10 false 4 5.583,1.531 6.198,1.729 0.615,0.198 10 false 3 5.583,2.031 6.198,2.229 0.615,0.198 10 false 1 5.594,2.552 6.208,2.75 0.615,0.198 10 false 5 3.563,0.625 4.177,0.823 0.615,0.198 10 false 2 3.563,1.146 4.177,1.344 0.615,0.198 10 false 4 3.563,1.656 4.177,1.854 0.615,0.198 10 false 3 3.552,2.167 4.167,2.365 0.615,0.198 10 false 1 2.042,2.677 2.656,2.875 0.615,0.198 10 false 5 4.385,2.76 5,2.958 0.615,0.198 10 false * 2.042,0.646 2.656,0.844 0.615,0.198 10 false 2 2.031,1.167 2.646,1.365 0.615,0.198 10 false 1 2.042,5.698 2.656,5.896 0.615,0.198 10 false 3 2.042,2.167 2.656,2.365 0.615,0.198 10 false 4 3.01,0.635 3.625,0.833 0.615,0.198 10 false LCB+ 3.031,1.146 3.646,1.344 0.615,0.198 10 false LCV+ 3.031,1.656 3.646,1.854 0.615,0.198 10 false LCV- 3.031,2.167 3.646,2.365 0.615,0.198 10 false LGND 3.031,2.677 3.646,2.875 0.615,0.198 10 false SGND 3.573,2.677 4.188,2.875 0.615,0.198 10 false 5 1.542,0.771 2.156,0.969 0.615,0.198 10 false CB+ 1.563,1.281 2.177,1.479 0.615,0.198 10 false CV+ 1.573,1.781 2.188,1.979 0.615,0.198 10 false CV- 1.552,2.281 2.167,2.479 0.615,0.198 10 false GND 1.479,2.802 2.094,3 0.615,0.198 10 false SGND 2.042,3.188 2.656,3.385 0.615,0.198 10 false LL1 2.052,3.375 4.344,3.979 2.292,0.604 10 false Outer Rear View Mirror Assembly LH (Television Camera Wire LH) 5.594,4.563 6.208,4.76 0.615,0.198 10 false 2 5.583,5.063 6.198,5.26 0.615,0.198 10 false 4 5.583,5.583 6.198,5.781 0.615,0.198 10 false 3 5.573,6.083 6.188,6.281 0.615,0.198 10 false 1 5.583,6.594 6.198,6.792 0.615,0.198 10 false 5 5.969,4.833 6.583,5.031 0.615,0.198 10 false RCB+ 3.021,5.188 3.635,5.385 0.615,0.198 10 false RCV+ 5.969,5.833 6.583,6.031 0.615,0.198 10 false RCV- 5.969,6.333 6.583,6.531 0.615,0.198 10 false RGND 5.969,6.844 6.583,7.042 0.615,0.198 10 false SGND 3.563,4.688 4.177,4.885 0.615,0.198 10 false 2 3.563,5.188 4.177,5.385 0.615,0.198 10 false 4 3.563,5.698 4.177,5.896 0.615,0.198 10 false 3 3.563,6.208 4.177,6.406 0.615,0.198 10 false 1 3.563,6.719 4.177,6.917 0.615,0.198 10 false 5 3.031,4.688 3.646,4.885 0.615,0.198 10 false RCB+ 5.969,5.323 6.583,5.521 0.615,0.198 10 false RCV+ 3.042,5.708 3.656,5.906 0.615,0.198 10 false RCV- 3.021,6.219 3.635,6.417 0.615,0.198 10 false RGND 3.021,6.719 3.635,6.917 0.615,0.198 10 false SGND 1.563,4.823 2.177,5.021 0.615,0.198 10 false CB+ 1.552,5.323 2.167,5.521 0.615,0.198 10 false CV+ 1.573,5.823 2.188,6.021 0.615,0.198 10 false CV- 1.552,6.354 2.167,6.552 0.615,0.198 10 false GND 1.469,6.854 2.083,7.052 0.615,0.198 10 false SGND 2.042,4.688 2.656,4.885 0.615,0.198 10 false 2 2.042,5.188 2.656,5.385 0.615,0.198 10 false 1 2.042,1.656 2.656,1.854 0.615,0.198 10 false 3 2.042,6.208 2.656,6.406 0.615,0.198 10 false 4 2.031,6.698 2.646,6.896 0.615,0.198 10 false 5 5.656,7.406 6.979,7.74 1.323,0.333 10 false Parking Assist ECU 0.396,3.177 1.01,3.375 0.615,0.198 10 false L15 0.375,3.375 1.823,3.729 1.448,0.354 10 false Side Television Camera Assembly LH 0.365,7.219 0.979,7.417 0.615,0.198 10 false K15 0.354,7.396 1.813,7.823 1.458,0.427 10 false Side Television Camera Assembly RH 0.177,8.479 2.802,8.688 2.625,0.208 10 false *: Shielded 4.385,6.813 5,7.01 0.615,0.198 10 false * 2.229,7.219 2.844,7.417 0.615,0.198 10 false KK1 2.208,7.406 4.51,7.813 2.302,0.406 10 false Outer Rear View Mirror Assembly RH (Television Camera Wire RH) 5.438,4.802 6.052,5 0.615,0.198 10 false O121 5.448,1.271 6.063,1.469 0.615,0.198 10 false O122 5.448,1.771 6.063,1.969 0.615,0.198 10 false O122 5.448,2.281 6.063,2.479 0.615,0.198 10 false O122 5.448,2.792 6.063,2.99 0.615,0.198 10 false O122 5.448,5.313 6.063,5.51 0.615,0.198 10 false O121 5.448,5.813 6.063,6.01 0.615,0.198 10 false O121 5.448,6.323 6.063,6.521 0.615,0.198 10 false O121 5.448,6.833 6.063,7.031 0.615,0.198 10 false O121

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park)>CALIBRATION


HINT:
Images may be unclear even in normal conditions if:
·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The television camera assembly lens is scratched.

·

The television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK PANORAMIC VIEW MONITOR SYSTEM
a.

Check if the same malfunction occurs when the panoramic view monitor screen is displayed.


Result:
Result Proceed to
Rear view screen is not displayed. A
Front view screen is not displayed. B
Side monitor screen (LH side) is not displayed. C
Side monitor screen (RH side) is not displayed. D
Panoramic view monitor screen is not displayed. E



A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH))

D

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH))

E

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the O123 parking assist ECU connector.


b.

Disconnect the Y35 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O123,Y35)Location & Routing

Click Connector(O123)Body>Floor Wire>Parking Assist ECU

Click Connector(Y35)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

O123-2 (CB+) - Y35-2 (CB+) Always Below 1 Ω
O123-4 (CV+) - Y35-4 (CV+) Always Below 1 Ω
O123-3 (CV-) - Y35-3 (CV-) Always Below 1 Ω
O123-1 (CGND) - Y35-1 (CGND) Always Below 1 Ω
O123-5 (SGND) - Y35-5 (SGND) Always Below 1 Ω
O123-2 (CB+) or Y35-2 (CB+) - Body ground Always 10 kΩ or higher
O123-4 (CV+) or Y35-4 (CV+) - Body ground Always 10 kΩ or higher
O123-3 (CV-) or Y35-3 (CV-) - Body ground Always 10 kΩ or higher
O123-1 (CGND) or Y35-1 (CGND) - Body ground Always 10 kΩ or higher
O123-5 (SGND) - Y35-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (CV-, CGND)
a.
E394295C09
0.188,0.927 0.698,1.24 0.51,0.313 2,0.854 2.563,0.531 true 1.99,1.094 2.573,1.552 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.646,0.417 3.167,0.615 0.521,0.198 10 false CGND 2.667,1.49 3.188,1.688 0.521,0.198 10 false CV- 0.271,0.99 0.885,1.188 0.615,0.198 10 false O123
*a Component without harness connected
(Parking Assist ECU)


Disconnect the O123 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O123)Location & Routing

Click Connector(O123)Body>Floor Wire>Parking Assist ECU

O123-1 (CGND) - Body ground Always Below 1 Ω
O123-3 (CV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

4.CHECK PARKING ASSIST ECU (CB+, CGND)
a.

Disconnect the Y35 rear television camera assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y35)Location & Routing

Click Connector(Y35)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

Y35-1 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Y35)Location & Routing

Click Connector(Y35)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

Y35-2 (CB+) - Y35-1 (CGND) Ignition switch ON 7 to 8 V
Y35-2 (CB+) - Y35-1 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the O120 parking assist ECU connector.


b.

Disconnect the B18 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O120,B18)Location & Routing

Click Connector(O120)Body>Floor Wire>Parking Assist ECU

Click Connector(B18)Engine Compartment>No. 3 Engine Room Wire>Front Television Camera Assembly

O120-2 (BCB+) - B18-2 (BCB+) Always Below 1 Ω
O120-4 (BCV+) - B18-4 (BCV+) Always Below 1 Ω
O120-3 (BCV-) - B18-3 (BCV-) Always Below 1 Ω
O120-1 (BGND) - B18-1 (BGND) Always Below 1 Ω
O120-5 (SGND) - B18-5 (SGND) Always Below 1 Ω
O120-2 (BCB+) or B18-2 (BCB+) - Body ground Always 10 kΩ or higher
O120-4 (BCV+) or B18-4 (BCV+) - Body ground Always 10 kΩ or higher
O120-3 (BCV-) or B18-3 (BCV-) - Body ground Always 10 kΩ or higher
O120-1 (BGND) or B18-1 (BGND) - Body ground Always 10 kΩ or higher
O120-5 (SGND) or B18-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK PARKING ASSIST ECU (BCV-, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU (BCV-, BGND)
a.
E394296C10
0.25,1 0.781,1.292 0.531,0.292 1.99,0.875 2.521,0.427 true 1.979,1.115 2.552,1.563 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 2.615,0.344 3.229,0.542 0.615,0.198 10 false BGND 2.625,1.5 3.24,1.698 0.615,0.198 10 false BCV- 0.333,1.052 0.948,1.25 0.615,0.198 10 false O120
*a Component without harness connected
(Parking Assist ECU)


Disconnect the O120 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O120)Location & Routing

Click Connector(O120)Body>Floor Wire>Parking Assist ECU

O120-1 (BGND) - Body ground Always Below 1 Ω
O120-3 (BCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

7.CHECK PARKING ASSIST ECU (BCB+, BGND)
a.

Disconnect the B18 front television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B18)Location & Routing

Click Connector(B18)Engine Compartment>No. 3 Engine Room Wire>Front Television Camera Assembly

B18-1 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B18)Location & Routing

Click Connector(B18)Engine Compartment>No. 3 Engine Room Wire>Front Television Camera Assembly

B18-2 (BCB+) - B18-1 (BGND) Ignition switch ON 7 to 8 V
B18-2 (BCB+) - B18-1 (BGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH))
a.

Disconnect the O122 parking assist ECU connector.


b.

Disconnect the LL1 outer rear view mirror assembly LH (television camera wire LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O122,LL1)Location & Routing

Click Connector(O122)Body>Floor Wire>Parking Assist ECU

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

O122-2 (LCB+) - LL1-2 (LCB+) Always Below 1 Ω
O122-4 (LCV+) - LL1-4 (LCV+) Always Below 1 Ω
O122-3 (LCV-) - LL1-3 (LCV-) Always Below 1 Ω
O122-1 (LGND) - LL1-1 (LGND) Always Below 1 Ω
O122-5 (SGND) - LL1-5 (SGND) Always Below 1 Ω
O122-2 (LCB+) or LL1-2 (LCB+) - Body ground Always 10 kΩ or higher
O122-4 (LCV+) or LL1-4 (LCV+) - Body ground Always 10 kΩ or higher
O122-3 (LCV-) or LL1-3 (LCV-) - Body ground Always 10 kΩ or higher
O122-1 (LGND) or LL1-1 (LGND) - Body ground Always 10 kΩ or higher
O122-5 (SGND) or LL1-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK PARKING ASSIST ECU (LCV-, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK PARKING ASSIST ECU (LCV-, LGND)
a.
E394297C17
0.208,0.979 0.74,1.26 0.531,0.281 1.969,0.875 2.552,0.521 true 1.979,1.135 2.563,1.521 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 2.656,0.427 3.271,0.625 0.615,0.198 10 false LGND 2.646,1.438 3.26,1.635 0.615,0.198 10 false LCV- 0.292,1.031 0.906,1.229 0.615,0.198 10 false O122
*a Component without harness connected
(Parking Assist ECU)


Disconnect the O122 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O122)Location & Routing

Click Connector(O122)Body>Floor Wire>Parking Assist ECU

O122-1 (LGND) - Body ground Always Below 1 Ω
O122-3 (LCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

10.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.

Disconnect the LL1 outer rear view mirror assembly LH (television camera wire LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(LL1)Location & Routing

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

LL1-1 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(LL1)Location & Routing

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

LL1-2 (LCB+) - LL1-1 (LGND) Ignition switch ON 7 to 8 V
LL1-2 (LCB+) - LL1-1 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

11.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH)

NG

11.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH)
a.
E434382C43
1.5,1.948 1.906,2.177 0.406,0.229 1.5,0.115 2,0.365 0.5,0.25 0.854,3.333 1.594,2.99 true 2.427,3.406 1.771,3.167 true 2.396,3.198 1.802,2.99 true 2.385,2.427 1.802,2.802 true 0.885,2.385 1.615,2.792 true 2.469,1.719 1.781,1.271 true 2.479,1.427 1.885,1.135 true 2.448,0.573 1.854,0.969 true 0.896,0.573 1.594,0.969 true 0.833,1.427 1.552,1.146 true 0.094,0.177 0.406,0.375 0.313,0.198 10 false *a 1.583,1.979 1.896,2.177 0.313,0.198 10 false L15 0.146,2.01 0.458,2.208 0.313,0.198 10 false *b 2.552,0.5 3.167,0.698 0.615,0.198 10 false LCB+ 0.469,1.417 1.083,1.615 0.615,0.198 10 false LCV- 2.552,1.417 3.167,1.615 0.615,0.198 10 false LCV+ 0.469,0.5 1.083,0.698 0.615,0.198 10 false LGND 2.552,1.667 3.167,1.865 0.615,0.198 10 false SGND 0.531,3.25 1.146,3.448 0.615,0.198 10 false CV- 2.5,3.135 3.115,3.333 0.615,0.198 10 false GND 2.469,2.333 3.083,2.531 0.615,0.198 10 false CB+ 0.521,2.313 1.135,2.51 0.615,0.198 10 false CV+ 2.5,3.365 3.115,3.563 0.615,0.198 10 false SGND 1.646,0.177 1.896,0.375 0.25,0.198 10 false LL1
*a Component without harness connected
(Outer Rear View Mirror Assembly LH (Television Camera Wire LH))
*b Front view of wire harness connector
(to Side Television Camera Assembly LH)


Disconnect the outer rear view mirror assembly LH (television camera wire LH) connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(LL1,L15)Location & Routing

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

Click Connector(L15)Body>Front Door Wire LH / Television Camera Wire>Side Television Camera Assembly LH

LL1-2 (LCB+) - L15-2 (CB+) Always Below 1 Ω
LL14 (LCV+) - L15-1 (CV+) Always Below 1 Ω
LL1-3 (LCV-) - L15-3 (CV-) Always Below 1 Ω
LL1-1 (LGND) - L15-4 (GND) Always Below 1 Ω
LL1-5 (SGND) - L15-5 (SGND) Always Below 1 Ω
LL1-2 (LCB+) or L15-2 (CB+) - Body ground Always 10 kΩ or higher
LL14 (LCV+) or L15-1 (CV+) - Body ground Always 10 kΩ or higher
LL1-3 (LCV-) or L15-3 (CV-) - Body ground Always 10 kΩ or higher
LL1-1 (LGND) or L15-4 (GND) - Body ground Always 10 kΩ or higher
LL1-5 (SGND) or L15-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH)

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

NG

13.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH))
a.

Disconnect the O121 parking assist ECU connector.


b.

Disconnect the KK1 outer rear view mirror assembly RH (television camera wire RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
T ester Connection Condition Specified Condition
O121-2 (RCB+) - KK1-2 (RCB+) Always Below 1 Ω
O121-4 (RCV+) - KK1-4 (RCV+) Always Below 1 Ω
O121-3 (RCV-) - KK1-3 (RCV-) Always Below 1 Ω
O121-1 (RGND) - KK1-1 (RGND) Always Below 1 Ω
O121-5 (SGND) - KK1-5 (SGND) Always Below 1 Ω
O121-2 (RCB+) or KK1-2 (RCB+) - Body ground Always 10 kΩ or higher
O121-4 (RCV+) or KK1-4 (RCV+) - Body ground Always 10 kΩ or higher
O121-3 (RCV-) or KK1-3 (RCV-) - Body ground Always 10 kΩ or higher
O121-1 (RGND) or KK1-1 (RGND) - Body ground Always 10 kΩ or higher
O121-5 (SGND) or KK1-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK PARKING ASSIST ECU (RCV-, RGND)
a.
E394298C05
0.167,0.979 0.708,1.26 0.542,0.281 1.979,0.896 2.531,0.542 true 1.969,1.115 2.552,1.333 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.635,0.448 3.083,0.646 0.448,0.198 10 false RGND 2.635,1.26 3.083,1.458 0.448,0.198 10 false RCV- 0.26,1.031 0.708,1.229 0.448,0.198 10 false O121
*a Component without harness connected
(Parking Assist ECU)


Disconnect the O121 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O121)Location & Routing

Click Connector(O121)Body>Floor Wire>Parking Assist ECU

O121-1 (RGND) - Body ground Always Below 1 Ω
O121-3 (RCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

15.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.

Disconnect the KK1 outer rear view mirror assembly RH (television camera wire RH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(KK1)Location & Routing

Click Connector(KK1)Body>Front Door Wire RH / Television Camera Wire>Television Camera Wire and Front Door Wire RH

KK1-1 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(KK1)Location & Routing

Click Connector(KK1)Body>Front Door Wire RH / Television Camera Wire>Television Camera Wire and Front Door Wire RH

KK1-2 (RCB+) - KK1-1 (RGND) Ignition switch ON 7 to 8 V
KK1-2 (RCB+) - KK1-1 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

16.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH)

NG

16.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH)
a.
E434382C45
1.5,1.948 1.906,2.177 0.406,0.229 1.5,0.115 2,0.365 0.5,0.25 0.938,3.313 1.625,2.99 true 2.427,3.406 1.771,3.167 true 2.396,3.198 1.802,2.99 true 2.385,2.427 1.802,2.802 true 0.917,2.396 1.615,2.792 true 2.469,1.708 1.781,1.302 true 2.438,1.469 1.896,1.125 true 2.448,0.573 1.854,0.969 true 0.896,0.573 1.594,0.969 true 0.885,1.469 1.552,1.135 true 0.094,0.177 0.406,0.375 0.313,0.198 10 false *a 1.583,1.979 1.896,2.177 0.313,0.198 10 false K15 0.146,2.01 0.458,2.208 0.313,0.198 10 false *b 2.552,0.5 3.167,0.698 0.615,0.198 10 false RCB+ 0.469,1.417 1.083,1.615 0.615,0.198 10 false RCV- 2.552,1.417 3.167,1.615 0.615,0.198 10 false RCV+ 0.469,0.5 1.083,0.698 0.615,0.198 10 false RGND 2.552,1.667 3.167,1.865 0.615,0.198 10 false SGND 0.604,3.25 1.219,3.448 0.615,0.198 10 false CV- 2.479,3.125 3.094,3.323 0.615,0.198 10 false GND 2.469,2.333 3.083,2.531 0.615,0.198 10 false CB+ 0.552,2.313 1.167,2.51 0.615,0.198 10 false CV+ 2.5,3.365 3.115,3.563 0.615,0.198 10 false SGND 1.625,0.156 1.948,0.365 0.323,0.208 10 false KK1
*a Component without harness connected
(Outer Rear View Mirror Assembly RH (television camera wire RH))
*b Front view of wire harness connector
(to Side Television Camera Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH (television camera wire RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(KK1,K15)Location & Routing

Click Connector(KK1)Body>Front Door Wire RH / Television Camera Wire>Television Camera Wire and Front Door Wire RH

Click Connector(K15)Body>Front Door Wire RH / Television Camera Wire>Side Television Camera Assembly RH

KK1-2 (RCB+) - K15-2 (CB+) Always Below 1 Ω
KK1-4 (RCV+) - K15-1 (CV+) Always Below 1 Ω
KK1-3 (RCV-) - K15-3 (CV-) Always Below 1 Ω
KK1-1 (RGND) - K15-4 (GND) Always Below 1 Ω
KK1-5 (SGND) - K15-5 (SGND) Always Below 1 Ω
KK1-2 (RCB+) or K15-2 (CB+) - Body ground Always 10 kΩ or higher
KK1-4 (RCV+) or K15-1 (CV+) - Body ground Always 10 kΩ or higher
KK1-3 (RCV-) or K15-3 (CV-) - Body ground Always 10 kΩ or higher
KK1-1 (RGND) or K15-4 (GND) - Body ground Always 10 kΩ or higher
KK1-5 (SGND) or K15-5 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (TELEVISION CAMERA WIRE RH)

17.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


b.

Check if the same malfunction reoccurs when the side monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal)



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

NG

18.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the O118 parking assist ECU connector.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O118,H80)Location & Routing

Click Connector(O118)Body>Floor Wire>Parking Assist ECU

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

O118-5 (RSW+) - H80-18 (CSW+) Always Below 1 Ω
O118-5 (RSW+) or H80-18 (CSW+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Replace the H80 radio and display receiver assembly with a new one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (RADIO AND DISPLAY RECEIVER ASSEMBLY WAS DEFECTIVE)

NG