Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486937 LIGHTING SYSTEM(w/ Adaptive High Beam System) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Adaptive High Beam System)  B242487  Leveling Motor LH Missing Message  B242587  Leveling Motor RH Missing Message  


DESCRIPTION

The headlight ECU sub-assembly sends the automatic headlight beam leveling control signal to the headlight leveling motor via LIN communication. The headlight leveling motor operates according to the power supply and automatic headlight beam leveling control signals received from the headlight ECU sub-assembly and sends its operating state to the headlight ECU sub-assembly via LIN communication.

The headlight ECU sub-assembly sends the adaptive high beam system control signal to the light control LED ECU via LIN communication.

The light control LED ECU receives the power supply and control signals from the headlight ECU sub-assembly and controls the LED array and LED array fan, and sends its operating state to the headlight ECU sub-assembly via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B242487 Leveling Motor LH Missing Message
Detection condition:

The ignition switch is ON.


Malfunction status:

LIN communication is lost with headlight leveling motor LH


Malfunction duration:

10 seconds or more


·

Headlight unit assembly LH

·

Headlight leveling motor LH

·

Headlight ECU sub-assembly LH


Headlight Control A
B242587 Leveling Motor RH Missing Message
Detection condition:

The ignition switch is ON.


Malfunction status:

LIN communication is lost with headlight leveling motor RH


Malfunction duration:

10 seconds or more


·

Harness or connector

·

Headlight unit assembly RH

·

Headlight leveling motor RH

·

Headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH


Headlight Control A

Output DTC Suspected Area (Malfunction Status)
B242487 B242587 B244087 B244187

○: DTC is output

-: DTC is not output

○ ○ ○ ○ LIN communication circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
○ - ○ - Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - ○ LIN communication circuit (open)
Headlight ECU sub-assembly RH (Internal malfunction)
Headlight ECU sub-assembly LH (Internal malfunction)
○ - - - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - - Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
- - ○ - Light control LED ECU LH power supply system abnormal
Light control LED ECU LH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly LH to light control LED ECU LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- - - ○ Light control LED ECU RH power supply system abnormal
Light control LED ECU RH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly RH to light control LED ECU RH)
Headlight ECU sub-assembly RH (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

E442330E18
1.625,0.74 2.177,0.948 0.552,0.208 10 false LIN I/F 0.948,2.323 1.563,2.521 0.615,0.198 10 false LINL 2.271,1.063 2.885,1.26 0.615,0.198 10 false LIN1_1 2.344,1.635 3.115,1.833 0.771,0.198 10 false ACTB 2.333,2.146 3.104,2.344 0.771,0.198 10 false ACTG 2,3.99 2.313,4.188 0.313,0.198 10 false IG 2,1.396 2.313,1.594 0.313,0.198 10 false IG 2.146,4.24 2.76,4.438 0.615,0.198 10 false PSWH2+ 0.531,2.5 0.99,2.698 0.458,0.198 10 false A110 0.615,2.292 0.927,2.49 0.313,0.198 10 false 20 2.906,1.26 3.063,1.458 0.156,0.198 10 false C 2.917,2.271 3.073,2.469 0.156,0.198 10 false B 2.917,1.76 3.073,1.958 0.156,0.198 10 false B 2.917,4.969 3.073,5.167 0.156,0.198 10 false C 2.906,3.75 3.063,3.948 0.156,0.198 10 false C 2.917,4.365 3.073,4.563 0.156,0.198 10 false C 5.198,5.688 5.354,5.885 0.156,0.198 10 false D 5.531,3.75 5.99,3.948 0.458,0.198 10 false LIN 2.865,1.052 3.177,1.25 0.313,0.198 10 false 12 2.906,1.563 3.063,1.76 0.156,0.198 10 false 9 2.875,2.073 3.188,2.271 0.313,0.198 10 false 18 5.042,2.813 6.875,3.094 1.833,0.281 10 false Headlight Leveling Motor LH 2.875,3.552 3.104,3.76 0.229,0.208 10 false 13 2.917,4.167 3.073,4.365 0.156,0.198 10 false 1 2.927,4.771 3.083,4.969 0.156,0.198 10 false 2 5.229,3.583 5.615,3.823 0.385,0.24 10 false 13 5.229,4.25 5.594,4.521 0.365,0.271 10 false 12 5.25,4.854 5.438,5.042 0.188,0.188 10 false 21 5.51,4.375 6.219,4.646 0.708,0.271 10 false ADD+ 5.521,4.979 6.188,5.281 0.667,0.302 10 false ADD- 5.208,5.854 6.958,6.042 1.75,0.188 10 false Light Control LED ECU LH 3.969,6.521 6.573,6.719 2.604,0.198 10 false Headlight Unit Assembly LH 0.656,6.844 3.198,7.052 2.542,0.208 10 false Headlight ECU Sub-assembly LH 0.198,6.708 0.354,6.906 0.156,0.198 10 false A 0.813,7.458 2.625,7.677 1.813,0.219 10 false : LIN Communication Line 5.042,2.656 5.354,2.854 0.313,0.198 10 false F 5.292,1.083 5.448,1.281 0.156,0.198 10 false 3 5.302,1.635 5.458,1.833 0.156,0.198 10 false 1 5.313,2.146 5.469,2.344 0.156,0.198 10 false 4 2.25,3.563 2.865,3.76 0.615,0.198 10 false LIN1_2 2.177,4.813 2.792,5.01 0.615,0.198 10 false PSWH2-

E442331E18
0.188,0.188 0.542,0.479 0.354,0.292 10 false A 0.531,2.5 0.99,2.698 0.458,0.198 10 false A111 0.615,2.302 0.927,2.5 0.313,0.198 10 false 20 2.01,1.406 2.323,1.604 0.313,0.198 10 false IG 2,4.01 2.313,4.208 0.313,0.198 10 false IG 2.271,1.063 3.042,1.26 0.771,0.198 10 false LIN1_1 2.333,2.125 3.104,2.323 0.771,0.198 10 false ACTG 2.344,1.615 3.115,1.813 0.771,0.198 10 false ACTB 2.917,1.25 3.073,1.448 0.156,0.198 10 false C 2.927,2.271 3.083,2.469 0.156,0.198 10 false B 2.927,1.76 3.083,1.958 0.156,0.198 10 false B 2.875,1.042 3.188,1.24 0.313,0.198 10 false 12 2.927,1.563 3.083,1.76 0.156,0.198 10 false 9 2.885,2.063 3.198,2.26 0.313,0.198 10 false 18 5.115,2.656 5.271,2.854 0.156,0.198 10 false F 5.302,2.146 5.458,2.344 0.156,0.198 10 false 4 5.292,1.094 5.448,1.292 0.156,0.198 10 false 3 5.292,1.646 5.448,1.844 0.156,0.198 10 false 1 5.125,2.802 6.896,3.146 1.771,0.344 10 false Headlight Leveling Motor RH 2.25,3.563 3.021,3.76 0.771,0.198 10 false LIN1_2 2.146,4.26 2.76,4.458 0.615,0.198 10 false PSWH2+ 2.177,4.833 2.792,5.031 0.615,0.198 10 false PSWH2- 2.917,4.969 3.073,5.167 0.156,0.198 10 false C 2.906,3.76 3.063,3.958 0.156,0.198 10 false C 2.906,4.385 3.063,4.583 0.156,0.198 10 false C 2.906,4.188 3.063,4.385 0.156,0.198 10 false 1 2.865,3.552 3.156,3.823 0.292,0.271 10 false 13 2.927,4.771 3.396,5.031 0.469,0.26 10 false 2 5.229,4.271 5.51,4.51 0.281,0.24 10 false 12 5.219,3.594 5.531,3.792 0.313,0.198 10 false 13 5.51,3.75 5.969,3.948 0.458,0.198 10 false LIN 5.25,4.854 5.563,5.052 0.313,0.198 10 false 21 5.521,4.365 6.052,4.594 0.531,0.229 10 false ADD+ 5.521,4.948 6.25,5.208 0.729,0.26 10 false ADD- 5.115,5.823 6.823,6.052 1.708,0.229 10 false Light Control LED ECU RH 3.875,6.521 6.479,6.719 2.604,0.198 10 false Headlight Unit Assembly RH 0.813,6.854 4.333,7.052 3.521,0.198 10 false Headlight ECU Sub-assembly RH 0.823,7.469 2.708,7.646 1.885,0.177 10 false : LIN Communication Line 0.927,2.333 1.26,2.51 0.333,0.177 10 false LINL 5.104,5.667 5.26,5.865 0.156,0.198 10 false D

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>INITIALIZATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are not output A
B242487, B242587, B244087 and B244187 are output B
B242487 and B244087 are output C
B242587 and B244187 are output D
B242487 is output E
B242587 is output F
B244087 is output G
B244187 is output H



Post-procedure1

a.

None



A

B

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

D

18.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

E

26.INSPECT HEADLIGHT UNIT ASSEMBLY LH

F

28.INSPECT HEADLIGHT UNIT ASSEMBLY RH

G

H

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the A110 headlight ECU sub-assembly LH connector.


b.

Disconnect the A111 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A110,A111)Location & Routing

Click Connector(A110)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly LH

Click Connector(A111)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly RH

A110-20 (LINL) - Body ground Always 10 kΩ or higher
A111-20 (LINL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC

Pre-procedure1

a.

Connect the A110 headlight ECU sub-assembly LH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

a.

None



A

6.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

15.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
6.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the A110 headlight ECU sub-assembly LH connector.


c.

Connect the A111 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 and B244087 are output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

9.CHECK HEADLIGHT LEVELING MOTOR LH
9.CHECK HEADLIGHT LEVELING MOTOR LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242487 is output B



Post-procedure1

a.

None



A

12.CHECK LIGHT CONTROL LED ECU LH

B

12.CHECK LIGHT CONTROL LED ECU LH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU LH connector.


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244087 is output B



Post-procedure1

a.

None



A

B

15.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Connect the A111 headlight ECU sub-assembly RH connector.


Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
16.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 and B244187 are output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

20.CHECK HEADLIGHT LEVELING MOTOR RH
18.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the A110 headlight ECU sub-assembly LH connector.


b.

Disconnect the A111 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A110,A111)Location & Routing

Click Connector(A110)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly LH

Click Connector(A111)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly RH

A110-20 (LINL) - A111-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

19.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

E473672C01
2.104,0.302 2.573,0.552 0.469,0.25 5.771,0.563 6.24,0.813 0.469,0.25 2.49,2.083 2.333,2.083 2.333,2.083 2.125,1.26 true 6.167,2.083 6,2.083 6,2.083 5.854,1.479 true 5.406,2.094 5.573,2.094 5.573,2.094 5.75,1.479 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.177,0.344 2.573,0.563 0.396,0.219 10 false A111 2.542,1.99 2.906,2.219 0.365,0.229 10 false LINL 4.917,2 5.458,2.229 0.542,0.229 10 false LIN1_2 5.948,0.604 6.313,0.833 0.365,0.229 10 false C 6.25,2 6.792,2.229 0.542,0.229 10 false LIN1_1
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A111)Location & Routing

Click Connector(A111)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly RH

A111-20 (LINL) - C-12 (LIN1_1) Always Below 1 Ω
A111-20 (LINL) - C-13 (LIN1_2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

20.CHECK HEADLIGHT LEVELING MOTOR RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Result:
Proceed to
NEXT



NEXT

21.CLEAR DTC
21.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

22.CHECK FOR DTC
22.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B242587 is output B



Post-procedure1

a.

None



A

23.CHECK LIGHT CONTROL LED ECU RH

B

23.CHECK LIGHT CONTROL LED ECU RH
a.

Connect all of the disconnected connectors.


b.

Disconnect the light control LED ECU RH connector.


Result:
Proceed to
NEXT



NEXT

24.CLEAR DTC
24.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Headlight Control > Clear DTCs
50002 462

Result:
Proceed to
NEXT



NEXT

25.CHECK FOR DTC
25.CHECK FOR DTC

Pre-procedure1

a.

Turn ignition switch to ON.


b.

Wait 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
B242487, B242587, B244087 and B244187 are output A
B244187 is output B



Post-procedure1

a.

None



A

B

26.INSPECT HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Procedure1

a.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight Leveling Motor LH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

27.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

NG

27.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor LH connector.


Procedure1

a.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

28.INSPECT HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Procedure1

a.

Measure the resistance according to the value(s) in the table below.

E401599C07
1.156,0.677 1.51,0.906 0.354,0.229 3.417,0.677 3.771,0.906 0.354,0.229 5.719,0.677 6.073,0.906 0.354,0.229 3.938,2.26 3.781,1.885 false 1.938,2.198 1.833,1.677 false 1.385,2.177 1.677,1.844 false 0.354,0.698 0.667,0.896 0.313,0.198 10 false *a 2.667,0.635 2.979,0.833 0.313,0.198 10 false *a 4.802,0.635 5.115,0.833 0.313,0.198 10 false *b 1.292,0.708 1.604,0.906 0.313,0.198 10 false B 3.552,0.708 3.865,0.906 0.313,0.198 10 false C 5.885,0.708 6.198,0.906 0.313,0.198 10 false F 3.813,2.292 4.583,2.49 0.771,0.198 10 false LIN1_1 1.802,2.229 2.573,2.427 0.771,0.198 10 false ACTB 1.198,2.208 1.969,2.406 0.771,0.198 10 false ACTG
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight Leveling Motor RH)


Standard Resistance:
Tester Connection Condition Specified Condition
C-12 (LIN1_1) - F-3 Always Below 1 Ω
B-9 (ACTB) - F-1 Always Below 1 Ω
B-18 (ACTG) - F-4 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

29.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

29.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Connect all of the disconnected connectors.


b.

Disconnect the headlight leveling motor RH connector.


Procedure1

a.
E378482C13
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.677,0.458 1.99,0.615 0.313,0.156 10 false F
*a Component without harness connected
(to Headlight Leveling Motor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F-1 - F-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH