Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486938 LIGHTING SYSTEM(w/o Adaptive High Beam System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Adaptive High Beam System)  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives the hazard warning signal switch assembly on signal and controls the operation of the hazard warning lights.

WIRING DIAGRAM

E367346E34
1.615,1.76 4.188,2.01 2.573,0.25 10 false Hazard Warning Signal Switch Assembly 1.615,1.594 2,1.802 0.385,0.208 10 false H59 1.927,1.094 2.219,1.333 0.292,0.24 10 false 4 2.115,1.094 2.406,1.333 0.292,0.24 10 false E 3.427,1.094 3.719,1.333 0.292,0.24 10 false TB 3.698,1.094 3.99,1.333 0.292,0.24 10 false 5 5.229,1.938 5.521,2.177 0.292,0.24 10 false H7 5.219,2.073 7.115,2.354 1.896,0.281 10 false Combination Meter Assembly 5.531,1.031 5.969,1.25 0.438,0.219 10 false HAZ 5.281,1.083 5.573,1.323 0.292,0.24 10 false 17 6.302,0.573 6.74,0.792 0.438,0.219 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard warning signal switch signal OFF or ON OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on
-
Body Electrical > Combination Meter > Data List
Tester Display
Hazard Flasher Switch
50003 409 39
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the H7 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H59,H7)Location & Routing

Click Connector(H59)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hazard Warning Signal Switch Assembly

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

H59-5 (TB) - H7-17 (HAZ) Always Below 1 Ω
H59-5 (TB) - Body ground Always 10 kΩ or higher
H7-17 (HAZ) - Body ground Always 10 kΩ or higher
H59-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR