Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0484174 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  Stereo Component Amplifier Malfunction  


WIRING DIAGRAM

E463267E01
0.646,0.24 3.708,0.552 3.063,0.313 10 false from Eco Run Vehicle Converter Assembly*1 1.906,0.802 4.865,1.052 2.958,0.25 10 false from Auxiliary Battery*2 0.635,1.323 4.063,1.531 3.427,0.208 10 false from Eco Run Vehicle Converter Assembly*1 3.865,0.969 4.854,1.198 0.99,0.229 10 false AMP NO. 1 3.865,2.083 4.854,2.313 0.99,0.229 10 false ECU-ACC 5.448,0.833 6,1.031 0.552,0.198 10 false H136 3.344,3.021 3.854,3.271 0.51,0.25 10 false TX1+ 5.854,3.031 6.365,3.281 0.51,0.25 10 false TX+ 3.385,3.719 3.896,3.969 0.51,0.25 10 false TX1- 2.563,4.042 3.552,4.271 0.99,0.229 10 false H79 2.563,4.229 4.26,4.583 1.698,0.354 10 false Radio and Display Receiver Assembly 0.146,4.885 3.104,5.135 2.958,0.25 10 false *1: w/ Stop and Start System 0.677,6.396 3.635,6.646 2.958,0.25 10 false : AVC-LAN Communication Line 5.781,5.927 7.031,6.292 1.25,0.365 10 false Stereo Component Amplifier Assembly 5.865,3.75 6.375,4 0.51,0.25 10 false TX- 5.458,1.896 6.01,2.094 0.552,0.198 10 false H137 5.458,3.042 6.01,3.24 0.552,0.198 10 false H137 5.448,3.719 6,3.917 0.552,0.198 10 false H137 5.438,4.51 5.99,4.708 0.552,0.198 10 false H136 5.448,5.26 6,5.458 0.552,0.198 10 false H136 5.875,0.823 6.427,1.021 0.552,0.198 10 false +B 5.875,1.885 6.427,2.083 0.552,0.198 10 false ACC 5.542,0.604 6.094,0.802 0.552,0.198 10 false 1 5.542,1.688 6.094,1.885 0.552,0.198 10 false 12 5.552,2.833 6.104,3.031 0.552,0.198 10 false 8 5.552,3.521 6.104,3.719 0.552,0.198 10 false 7 5.563,4.302 6.115,4.5 0.552,0.198 10 false 3 5.521,5.031 6.073,5.229 0.552,0.198 10 false 18 5.854,4.5 6.406,4.698 0.552,0.198 10 false GND 5.844,5.25 6.396,5.448 0.552,0.198 10 false GND2 3.792,2.875 4.344,3.073 0.552,0.198 10 false 5 3.802,3.552 4.354,3.75 0.552,0.198 10 false 6 2.229,1.896 5.188,2.146 2.958,0.25 10 false from ACC Relay*2 0.177,5.229 3.135,5.479 2.958,0.25 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type)>PRECAUTION


PROCEDURE

1.CHECK STATUS INDICATORS
a.

Check for color of status indicators.

Result:
Result Proceed to
External amplifier indicator is red A
External amplifier indicator is green B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.




A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

5.CHECK STATUS INDICATORS
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK FAULTS LIST
4.CHECK FAULTS LIST

NEXT

5.CHECK STATUS INDICATORS
5.CHECK STATUS INDICATORS

Result:
Result Proceed to
External amplifier indicator is red A
External amplifier indicator is green B



A

6.CHECK VEHICLE TYPE

B

6.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)

B

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the H136 and H137 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H136)Location & Routing

Click Connector(H136)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H136-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H136,H137)Location & Routing

Click Connector(H136)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

Click Connector(H137)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H136-1 (+B) - H136-3 (GND) Ignition switch off 11 to 14 V
H137-12 (ACC) - H136-3 (GND) Ignition switch ACC 11 to 14 V


Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the H137 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H79,H137)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H137)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H79-5 (TX1+) - H137-8 (TX+) Always Below 1 Ω
H79-6 (TX1-) - H137-7 (TX-) Always Below 1 Ω
H79-5 (TX1+) - Body ground Always 10 kΩ or higher
H79-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CLEAR FAULTS LIST
10.CLEAR FAULTS LIST

NEXT

11.CHECK STATUS INDICATORS
11.CHECK STATUS INDICATORS

Result:
Result Proceed to
External amplifier indicator is red A
External amplifier indicator is green B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the H136 and H137 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H136)Location & Routing

Click Connector(H136)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H136-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H136,H137)Location & Routing

Click Connector(H136)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

Click Connector(H137)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H136-1 (+B) - H136-3 (GND) Ignition switch off 10.5 to 16 V
H137-12 (ACC) - H136-3 (GND) Ignition switch ACC 10.5 to 16 V


Result:
Proceed to
OK
NG




OK

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the H137 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H79,H137)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H137)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H79-5 (TX1+) - H137-8 (TX+) Always Below 1 Ω
H79-6 (TX1-) - H137-7 (TX-) Always Below 1 Ω
H79-5 (TX1+) - Body ground Always 10 kΩ or higher
H79-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR FAULTS LIST
15.CLEAR FAULTS LIST

NEXT

16.CHECK STATUS INDICATORS
16.CHECK STATUS INDICATORS

Result:
Result Proceed to
External amplifier indicator is red A
External amplifier indicator is green B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)