Inspect the fuses for circuits related to this system before performing the following procedure.
Check for color of status indicators.
| Result | Proceed to |
|---|---|
| MM-SUB-BUS communication indicator is green | A |
| MM-SUB-BUS communication indicator is red | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Stop and Start System | A |
| w/ Stop and Start System | B |
A
B
Disconnect the H6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=23 |
||
| H6-23 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=22,38 |
||
| H6-22 (B) - Body ground | Ignition switch off | 11 to 14 V |
| H6-38 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Headup Display System | A |
| w/ Headup Display System | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=11,22 |
||
| H115-11 - H115-22 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Connect the H6 combination meter assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Connect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=27,10 |
||
| H6-27 (MSCH) - H6-10 (MSCL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=4 |
||
| H61-4 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=2,1 |
||
| H61-2 (B) - Body ground | Ignition switch off | 11 to 14 V |
| H61-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=11,22 |
||
| H115-11 - H115-22 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H61 headup display (meter mirror sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=9,20 |
||
| H115-9 - H115-20 | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=14,15 |
||
| H61-14 (TX+) - H61-15 (TX-) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H6 combination meter assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=27,10 |
||
| H6-27 (MSCH) - H6-10 (MSCL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=23 |
||
| H6-23 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=22,38 |
||
| H6-22 (B) - Body ground | Ignition switch off | 11 to 14 V |
| H6-38 (IG+) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Headup Display System | A |
| w/ Headup Display System | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=11,22 |
||
| H115-11 - H115-22 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Connect the H6 combination meter assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Connect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=27,10 |
||
| H6-27 (MSCH) - H6-10 (MSCL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=4 |
||
| H61-4 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=2,1 |
||
| H61-2 (B) - Body ground | Ignition switch off | 11 to 14 V |
| H61-1 (IG) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=11,22 |
||
| H115-11 - H115-22 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H61 headup display (meter mirror sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=9,20 |
||
| H115-9 - H115-20 | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=14,15 |
||
| H61-14 (TX+) - H61-15 (TX-) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H6 combination meter assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=27,10 |
||
| H6-27 (MSCH) - H6-10 (MSCL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG