Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) › from 2021.07
RM3700E _58 Vehicle Interior _093747 DOOR LOCK _0441961 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  B124296  Wireless Door Lock Tuner Component Internal Failure  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B124296 Wireless Door Lock Tuner Component Internal Failure
·

Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)


Entry&Start A

WIRING DIAGRAM

for 5 Pin Type


E408228C01
1.25,1.198 1.865,1.396 0.615,0.198 10 false DATA 1.427,2.24 2.042,2.438 0.615,0.198 10 false +5 5.792,1.208 6.406,1.406 0.615,0.198 10 false RDAM 5.792,2.271 6.406,2.469 0.615,0.198 10 false RCO 5.813,3.052 6.427,3.25 0.615,0.198 10 false E 1.302,3.042 1.917,3.24 0.615,0.198 10 false GND 0.604,3.542 1.219,3.74 0.615,0.198 10 false O48 5.531,3.542 7.042,3.885 1.51,0.344 10 false Certification ECU (Smart Key ECU Assembly) 0.604,3.729 2.385,4.24 1.781,0.51 10 false Door Control Receiver 1.719,1.219 2.333,1.417 0.615,0.198 10 false 5 1.708,2.24 2.323,2.438 0.615,0.198 10 false 4 1.708,2.927 2.323,3.125 0.615,0.198 10 false 1 5.448,3.042 6.063,3.24 0.615,0.198 10 false H46 5.448,1.313 6.063,1.51 0.615,0.198 10 false O47 5.448,2.365 6.063,2.563 0.615,0.198 10 false O47 5.49,1.104 6.104,1.302 0.615,0.198 10 false 11 5.479,2.833 6.094,3.031 0.615,0.198 10 false 29 5.49,2.167 6.104,2.365 0.615,0.198 10 false 21 0.75,1.813 0.938,2 0.188,0.188 10 false IC 6.229,0.813 6.469,1.01 0.24,0.198 10 false +B 6.25,1.833 6.49,2.031 0.24,0.198 10 false 5 V


for 12 Pin Type


E408228E18
1.25,1.198 1.865,1.396 0.615,0.198 10 false DATA 1.427,2.24 2.042,2.438 0.615,0.198 10 false +5 5.792,1.208 6.406,1.406 0.615,0.198 10 false RDAM 5.792,2.271 6.406,2.469 0.615,0.198 10 false RCO 5.813,3.052 6.427,3.25 0.615,0.198 10 false E 1.302,3.042 1.917,3.24 0.615,0.198 10 false GND 0.604,3.542 1.219,3.74 0.615,0.198 10 false O34 5.531,3.542 7.042,3.885 1.51,0.344 10 false Certification ECU (Smart Key ECU Assembly) 0.604,3.729 2.104,3.948 1.5,0.219 10 false Door Control Receiver 1.719,1.219 2.333,1.417 0.615,0.198 10 false 2 1.708,2.24 2.323,2.438 0.615,0.198 10 false 8 1.708,2.927 2.323,3.125 0.615,0.198 10 false 12 5.448,3.042 6.063,3.24 0.615,0.198 10 false H46 5.448,1.313 6.063,1.51 0.615,0.198 10 false O47 5.448,2.365 6.063,2.563 0.615,0.198 10 false O47 5.49,1.104 6.104,1.302 0.615,0.198 10 false 11 5.479,2.833 6.094,3.031 0.615,0.198 10 false 29 5.49,2.167 6.104,2.365 0.615,0.198 10 false 21 0.75,1.813 0.938,2 0.188,0.188 10 false IC 6.229,0.813 6.469,1.01 0.24,0.198 10 false +B 6.25,1.833 6.49,2.031 0.24,0.198 10 false 5 V


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, the performance of the entry function and wireless function may be affected.

·

This DTC is not stored within 10 seconds of the ignition switch being turned from on to off.

·

Make sure that there are no electrical key transmitter sub-assemblies in the vehicle.

·

If the door control receiver has been replaced, it is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs to the door control receiver assembly.*1

*1: for 12 Pin Type


·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.*1

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

*1: for 12 Pin Type




PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 5 Pin Type A
for 12 Pin Type B



A

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the O48 door control receiver connector.


Procedure1

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B574584C02
4.76,0.5 5.26,0.75 0.5,0.25 3.396,0.5 3.896,0.75 0.5,0.25 1.948,0.5 2.448,0.75 0.5,0.25 3.302,2.104 3.604,1.271 true 4.083,2.094 3.708,1.365 true 4.979,2.094 4.604,1.365 true 4.896,0.552 5.354,0.75 0.458,0.198 10 false H46 3.521,0.552 3.979,0.75 0.458,0.198 10 false O47 2.073,0.552 2.531,0.75 0.458,0.198 10 false H45 3.969,2.125 4.427,2.323 0.458,0.198 10 false RCO 4.948,2.115 5.406,2.313 0.458,0.198 10 false E 3.094,2.135 3.604,2.375 0.51,0.24 10 false RDAM 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H46)Location & Routing

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H46-29 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B574584C02
4.76,0.5 5.26,0.75 0.5,0.25 3.396,0.5 3.896,0.75 0.5,0.25 1.948,0.5 2.448,0.75 0.5,0.25 3.302,2.104 3.604,1.271 true 4.083,2.094 3.708,1.365 true 4.979,2.094 4.604,1.365 true 4.896,0.552 5.354,0.75 0.458,0.198 10 false H46 3.521,0.552 3.979,0.75 0.458,0.198 10 false O47 2.073,0.552 2.531,0.75 0.458,0.198 10 false H45 3.969,2.125 4.427,2.323 0.458,0.198 10 false RCO 4.948,2.115 5.406,2.313 0.458,0.198 10 false E 3.094,2.135 3.604,2.375 0.51,0.24 10 false RDAM 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O47,H46)Location & Routing

Click Connector(O47)Instrument Panel>Floor Wire>Certification ECU

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

O47-11 (RDAM) - H46-29 (E) Always 11 to 14 V
O47-21 (RCO) - H46-29 (E) Always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals


Result:
Proceed to
OK
NG




OK

REPLACE DOOR CONTROL RECEIVER

NG

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the O47 certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O47,O48)Location & Routing

Click Connector(O47)Instrument Panel>Floor Wire>Certification ECU

Click Connector(O48)Body>Floor Wire>Smart Door Control Receiver Assembly

O47-11 (RDAM) - O48-5 (DATA) Always Below 1 Ω
O47-21 (RCO) - O48-4 (+5) Always Below 1 Ω
O48-1 (GND) - Body ground Always Below 1 Ω
O48-5 (DATA) - Other terminals and body ground Always 10 kΩ or higher
O47-11 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
O48-4 (+5) - Other terminals and body ground Always 10 kΩ or higher
O47-21 (RCO) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the O34 door control receiver connector.


Procedure1

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B574584C02
4.76,0.5 5.26,0.75 0.5,0.25 3.396,0.5 3.896,0.75 0.5,0.25 1.948,0.5 2.448,0.75 0.5,0.25 3.302,2.104 3.604,1.271 true 4.083,2.094 3.708,1.365 true 4.979,2.094 4.604,1.365 true 4.896,0.552 5.354,0.75 0.458,0.198 10 false H46 3.521,0.552 3.979,0.75 0.458,0.198 10 false O47 2.073,0.552 2.531,0.75 0.458,0.198 10 false H45 3.969,2.125 4.427,2.323 0.458,0.198 10 false RCO 4.948,2.115 5.406,2.313 0.458,0.198 10 false E 3.094,2.135 3.604,2.375 0.51,0.24 10 false RDAM 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H46)Location & Routing

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H46-29 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B574584C02
4.76,0.5 5.26,0.75 0.5,0.25 3.396,0.5 3.896,0.75 0.5,0.25 1.948,0.5 2.448,0.75 0.5,0.25 3.302,2.104 3.604,1.271 true 4.083,2.094 3.708,1.365 true 4.979,2.094 4.604,1.365 true 4.896,0.552 5.354,0.75 0.458,0.198 10 false H46 3.521,0.552 3.979,0.75 0.458,0.198 10 false O47 2.073,0.552 2.531,0.75 0.458,0.198 10 false H45 3.969,2.125 4.427,2.323 0.458,0.198 10 false RCO 4.948,2.115 5.406,2.313 0.458,0.198 10 false E 3.094,2.135 3.604,2.375 0.51,0.24 10 false RDAM 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O47,H46)Location & Routing

Click Connector(O47)Instrument Panel>Floor Wire>Certification ECU

Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

O47-11 (RDAM) - H46-29 (E) Always 11 to 14 V
O47-21 (RCO) - H46-29 (E) Always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals


Result:
Proceed to
OK
NG




OK

REPLACE DOOR CONTROL RECEIVER

NG

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the O47 certification ECU (smart key ECU assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O47,O34)Location & Routing

Click Connector(O47)Instrument Panel>Floor Wire>Certification ECU

Click Connector(O34)Body>Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key and Tire Pressure Monitoring System Receiver Assembly)

O47-11 (RDAM) - O34-2 (DATA) Always Below 1 Ω
O47-21 (RCO) - O34-8 (+5) Always Below 1 Ω
O34-12 (GND) - Body ground Always Below 1 Ω
O34-2 (DATA)- Other terminals and body ground Always 10 kΩ or higher
O47-11 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
O34-8 (+5) - Other terminals and body ground Always 10 kΩ or higher
O47-21 (RCO) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR