Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › ECM › from 2021.07
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442036 ECM A

M15A-FXE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A476119N01
5.063,1.635 5.396,1.635 false 3.708,0.979 3.865,0.979 3.865,0.979 4.292,1.625 false 3.219,2.104 3.552,2.104 false 6.49,0.594 6.823,0.594 false 6.469,0.271 6.802,0.271 false 3.01,1.958 3.292,2.313 0.281,0.354 18 false 4 5.427,1.51 5.708,1.865 0.281,0.354 18 false 5 6.281,0.115 6.563,0.469 0.281,0.354 18 false 2 6.281,0.479 6.563,0.833 0.281,0.354 18 false 1 3.542,0.833 3.823,1.188 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 ECM 89661 (Click here) - -
4 NO. 1 ECM BRACKET 89667E - - -
5 NO. 2 ECM BRACKET 89668 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
ECU security key
·

DTCs are stored

·

Vehicle control history (RoB) are stored


(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

Click here(Click here)




Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89661 3.REMOVE ECM

a.
A458721N01
0.479,0.094 1.396,0.448 0.917,0.354 18 true i, ii, iii

i.

Raise the 2 lock levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



ii.

Disengage the clamp.


iii.

Remove the bolt, 2 nuts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




Hide 89667E 4.REMOVE NO. 1 ECM BRACKET

a.
A458723


Hide 89668 5.REMOVE NO. 2 ECM BRACKET

a.
A458722