Home › Engine / Hybrid System › M15A-FXE (FUEL) › FUEL PUMP › from 2021.07
RM3700E _51 Engine / Hybrid System _093309 M15A-FXE FUEL _0440432 FUEL PUMP A

M15A-FXE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A457015N02
2.948,2 3.281,2 false 6.49,0.25 6.823,0.25 false 6.417,0.719 6.75,0.719 false 4,2.583 4.333,2.583 false 3.948,2.958 4.281,2.958 false 5.073,3.604 5.406,3.604 false 3.854,3.75 4.188,3.75 false 3.073,4.698 3.406,4.698 false 2.542,2.448 2.708,2.448 2.708,2.448 2.875,2.813 false 2.031,2.292 1.813,1.833 1.813,1.833 1.646,1.833 false 1.073,0.667 1.406,0.667 false 2.885,4.646 3.094,4.844 0.208,0.198 10 false ● 4.396,2.521 4.604,2.719 0.208,0.198 10 false ● 6.208,0.594 6.49,0.948 0.281,0.354 18 false 3 6.021,0.115 6.563,0.469 0.542,0.354 18 false 1, 2 2.74,1.865 3.021,2.219 0.281,0.354 18 false 5 1.479,1.719 1.76,2.073 0.281,0.354 18 false 8 2.344,2.323 2.625,2.677 0.281,0.354 18 false 6 4.656,2.823 4.938,3.177 0.281,0.354 18 false 9 5.479,3.469 5.76,3.823 0.281,0.354 18 false 7 4.583,3.615 4.99,3.958 0.406,0.344 18 false 10 0.865,0.542 1.146,0.896 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 REAR SEAT ASSEMBLY - - - -
5 REAR FLOOR SERVICE HOLE COVER 58325E - - -
6 NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY 77027B - - -
7 NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY 77701W - - -
8 FUEL TANK MAIN TUBE SUB-ASSEMBLY 77209F (Click here) - -
9 FUEL PUMP GAUGE RETAINER 77144 (Click here) - -
10 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 77020A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of fuel pump Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR SEAT ASSEMBLY

Hide 58325E 5.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A459671C01
1.219,0.76 0.885,1 true 0.646,0.927 0.854,1.094 0.208,0.167 10 true *a
*a Protective Tape - -



Hide 77027B 6.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A459601


Hide 77701W 7.DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A459604


Hide 77209F 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A476520C01
5,1.344 5.208,1.167 false 4.896,0.698 5.313,0.698 false 1.781,1.042 2.021,1.302 true 5.896,0.833 6.313,0.917 6.313,0.917 5.896,0.958 true 5.75,0.281 5.979,0.125 false 4.667,0.083 5.01,0.323 false 1.01,1.385 1.365,1.385 true 4.813,1.302 5.125,1.458 0.313,0.156 10 false *1 4.719,0.635 5.031,0.792 0.313,0.156 10 false *2 2.052,1.24 2.25,1.427 0.198,0.188 10 true *3 6.063,0.031 6.375,0.188 0.313,0.156 10 false *a 6.354,0.844 6.667,1 0.313,0.156 10 false *b 4.5,0.01 4.813,0.167 0.313,0.156 10 false *c 0.792,1.313 1,1.479 0.208,0.167 10 true *2 0.417,0.052 0.552,0.344 0.135,0.292 18 true i
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Nylon Tube - -
V100135

Pull off
V100136

Pull off


i.

Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.





Hide 77144 9.REMOVE FUEL PUMP GAUGE RETAINER

a.
A459657C03
1.302,2.385 1.99,2.271 true 0.917,0.313 1.573,0.313 true 1.01,0.625 1.479,0.625 true 2.896,0.531 2.427,0.76 true 2.99,1.115 2.615,0.958 true 2.698,1.375 2.354,1.115 true 5.24,0.708 4.854,0.531 false 5.865,1.677 5.396,1.906 true 5.969,2.281 5.583,2.615 true 5.469,1.01 5.125,1.125 false 5.656,1.323 5.313,1.438 false 2.021,2.188 2.25,2.385 0.229,0.198 10 true *a 5.719,1.229 5.906,1.406 0.188,0.177 10 true *b 0.823,0.552 1.021,0.719 0.198,0.167 10 true *c 2.885,0.438 3.083,0.604 0.198,0.167 10 true *d 4.719,0.458 4.917,0.625 0.198,0.167 10 true *e 5.51,0.917 5.688,1.094 0.177,0.177 10 true *f 3,1.031 3.188,1.208 0.188,0.177 10 true *b 2.729,1.323 2.927,1.49 0.198,0.167 10 true *c 0.708,0.208 0.906,0.375 0.198,0.167 10 true *d 5.417,2.521 5.615,2.688 0.198,0.167 10 true *c 5.917,1.583 6.115,1.75 0.198,0.167 10 true *d 0.417,0.073 0.563,0.344 0.146,0.271 18 false i 4.219,0.094 5.083,0.396 0.865,0.302 18 false iii, iv, v 2.281,2.438 2.521,2.688 0.24,0.25 18 false ii
*a Insertion Point *b SST (Plate)
*c SST (Claw) *d SST (Bolt)
*e SST (Handle) *f Extension Bar


i.

Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.

Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 10.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A459674N02
0.427,0.104 0.573,0.354 0.146,0.25 18 true i 3.656,0.094 3.854,0.344 0.198,0.25 18 true ii

i.

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



ii.

Remove the fuel suction tube set gasket from the fuel tank assembly.