Home › General › MAINTENANCE › M15A-FXE COOLANT (for Engine) › from 2021.07
RM3700E _V1 General _093024 MAINTENANCE _0442329 M15A-FXE COOLANT(for Engine) A

MAINTENANCE  M15A-FXE COOLANT(for Engine)  REPLACEMENT  


PROCEDURE

Hide 53876A 1.SEPARATE FRONT FENDER LINER LH

A490180

a.

Remove the 2 clips and screw.


b.

Separate the front fender liner LH.


Hide 2.DRAIN ENGINE COOLANT (for Engine)

CAUTION:
·

When engine coolant is hot, do not remove the radiator cap sub-assembly or the radiator drain cock plug.

·

Fluid and steam may spray out due to high pressure, possibly resulting in burns.

A476143C01
5.74,3.385 6.063,3.385 true 5.802,1.719 5.802,1.385 true 5.729,1.792 5.958,1.99 0.229,0.198 10 true *1 6.146,3.302 6.375,3.5 0.229,0.198 10 true *2
*1 Radiator Cap Sub-assembly *2 Radiator Drain Cock Plug




a.
A461084C01
1.271,1.688 1.604,1.688 true 1.604,1.594 1.823,1.792 0.219,0.198 10 true *a
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.

Loosen the radiator drain cock plug.


c.

Remove the radiator cap sub-assembly. Then drain the engine coolant.

A461085C01
3.646,3.792 3.979,4.313 3.979,4.313 4.146,4.313 false 3.281,1.865 4.844,0.625 4.844,0.625 5.01,0.625 true 5.063,0.563 5.375,0.76 0.313,0.198 10 false *1 4.198,4.24 4.51,4.438 0.313,0.198 10 false *2
*1 Radiator Cap Sub-assembly *2 Radiator Drain Cock Plug


HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD ENGINE COOLANT (for Engine)

a.
A206788C24
2.417,1.573 2.521,1.823 false 2.729,0.302 2.938,0.875 false 3.083,1.167 3.417,1.396 0.333,0.229 10 false *c 2.438,1.833 2.604,1.99 0.167,0.156 10 false *b 2.594,0.135 2.76,0.292 0.167,0.156 10 false *a
*a Filler Tube End
*b Engine Coolant Level
*c 20 mm


Slowly fill the radiator assembly with engine coolant from the radiator inlet opening. (Engine coolant level should be within 20 mm (0.787 in.) from the filler tube end.)

Standard Capacity:
Item Specified Condition
for TMC Made 4.9 liters (5.2 US qts, 4.3 Imp. qts)
for TMMF Made 4.7 liters (5.0 US qts, 4.1 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



b.

Remove the reserve tank cap.


c.
A461079C02
1.125,0.927 1.917,0.927 true 0.917,0.844 1.208,1.052 0.292,0.208 10 false *a
*a F Line


Slowly pour engine coolant into the radiator reserve tank until it reaches the F line.


d.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

If the engine coolant level is low, add engine coolant.


e.

Install the radiator cap sub-assembly and reserve tank cap.


f.

Set the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


g.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off.

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.

Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

HINT:

The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.



ii.

After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)


iii.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.

NOTICE:
·

If the radiator reserve tank runs out of engine coolant just after the engine is started, stop the engine immediately, wait until the engine coolant has cooled down, and then add engine coolant.

·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

Make sure that the radiator reserve tank still has some engine coolant in it.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.

·

If the radiator reserve tank does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant cools down, and 3) add engine coolant until the radiator reserve tank is filled to the F line.





h.
A461079C01
1.146,0.927 1.927,0.927 true 1.135,1.635 1.917,1.635 true 0.948,0.854 1.323,1.063 0.375,0.208 10 false *a 0.927,1.583 1.292,1.823 0.365,0.24 10 false *b
*a F Line
*b L Line


After the engine has cooled down, check that the engine coolant level is between the F line and L line.

If the engine coolant level is below the L line, add engine coolant to the F line.


Hide 4.INSPECT FOR COOLANT LEAK (for Engine)

Hide 53876A 5.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH to the vehicle with the screw and 2 clips.