For vehicles equipped with VSC, if wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection.
MEASURE VEHICLE HEIGHT (FRONT WHEEL ALIGNMENT)
Ground clearance of front wheel center
Ground clearance of front lower arm set front bolt center
Ground clearance of rear wheel center
Ground clearance of axle beam set bolt center
Before inspecting the wheel alignment, check the vehicle height.
The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.
| Model | Tire Size | Front A-B | Rear C-D |
|---|---|---|---|
| Except for Rough Road Package | 175/70 R14 | 97 mm
(3.82 in.) |
32 mm
(1.26 in.) |
| 175/65 R15 | 97 mm
(3.82 in.) |
32 mm
(1.26 in.) |
|
| 175/65 R14 | 87 mm
(3.43 in.) |
25 mm
(0.98 in.) |
|
| 185/60 R15 | 87 mm
(3.43 in.) |
24 mm
(0.94 in.) |
|
| Rough Road Package | 175/65 R14 | 67 mm
(2.64 in.) |
5 mm
(0.20 in.) |
| 185/60 R15 | 67 mm
(2.64 in.) |
4 mm
(0.16 in.) |
INSPECT WHEEL TURNING ANGLE (FRONT WHEEL ALIGNMENT)
Fully turn the steering wheel left and right, and measure the wheel turning angle.
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
| Model | Tire Size | Inside Wheel | Outside Wheel |
|---|---|---|---|
| Except for Rough Road Package | 175/70 R14 | 40°44 ' +/- 2°
(40.73° +/- 2°) |
35°03'
(35.05°) |
| 175/65 R15 | 40°44 ' +/- 2°
(40.73° +/- 2°) |
35°03'
(35.05°) |
|
| 175/65 R14 | 41°01' +/- 2°
(41.02° +/- 2°) |
35°15'
(35.25°) |
|
| 185/60 R15 | 41°01' +/- 2°
(41.02° +/- 2°) |
35°15'
(35.25°) |
|
| Rough Road Package | 175/65 R14 | 41°35' +/- 2°
(41.58° +/- 2°) |
35°43'
(35.72°) |
| 185/60 R15 | 41°35' +/- 2°
(41.58° +/- 2°) |
35°43'
(35.72°) |
If the right and left inside wheel angles are not within the specified range, check the right and left rack end lengths.
INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)
Put the front wheel on the center of the alignment tester.
| *1 | Alignment tester |
| *2 | Camber-caster-steering axis inclination gauge |
Remove the wheel cap.
Set the camber-caster-steering axis inclination gauge at the center of the axle hub or drive shaft.
Inspect the camber, caster and steering axis inclination.
| Model | Tire Size | Camber |
|---|---|---|
| Except for Rough Road Package | 175/70 R14 | -0°21' +/- 45'
(-0.35° +/- 0.75°) |
| 175/65 R15 | -0°21' +/- 45'
(-0.35° +/- 0.75°) |
|
| 175/65 R14 | -0°15' +/- 45'
(-0.25° +/- 0.75°) |
|
| 185/60 R15 | -0°15' +/- 45'
(-0.25° +/- 0.75°) |
|
| Rough Road Package | 175/65 R14 | 0°02' +/- 45'
(0.03° +/- 0.75°) |
| 185/60 R15 | 0°02' +/- 45'
(0.03° +/- 0.75°) |
| Model | Tire Size | Transmission | Caster |
|---|---|---|---|
| Except for Rough Road Package | 175/70 R14 | C54
U441E |
4°59' +/- 45'
(4.98° +/- 0.75°) |
| 175/65 R15 | C54
U340E U441E |
4°60' +/- 45'
(5.00° +/- 0.75°) |
|
| 175/65 R14 | C54 | 4°53' +/- 45'
(4.88° +/- 0.75°) |
|
| U441E | 4°52' +/- 45'
(4.87° +/- 0.75°) |
||
| 185/60 R15 | C54 | 4°54' +/- 45'
(4.90° +/- 0.75°) |
|
| U340E
U441E |
4°53' +/- 45'
(4.88° +/- 0.75°) |
||
| Rough Road Package | 175/65 R14 | C54 | 4°34' +/- 45'
(4.57° +/- 0.75°) |
| U441E | 4°33' +/- 45'
(4.55° +/- 0.75°) |
||
| 185/60 R15 | C54 | 4°35' +/- 45'
(4.58° +/- 0.75°) |
|
| U340E
U441E |
4°34' +/- 45'
(4.57° +/- 0.75°) |
| Model | Tire Size | Steering Axis Inclination
(Reference) |
|---|---|---|
| Except for Rough Road Package | 175/70 R14 | 11°21'
(11.35°) |
| 175/65 R15 | 11°21'
(11.35°) |
|
| 175/65 R14 | 11°09'
(11.15°) |
|
| 185/60 R15 | 11°09'
(11.15°) |
|
| Rough Road Package | 175/65 R14 | 10°40'
(10.67°) |
| 185/60 R15 | 10°40'
(10.67°) |
Perform the inspection while the vehicle is empty (without a spare tire or tools on board).
The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.
Remove the camber-caster-steering axis inclination gauge and attachment.
Install the wheel cap.
If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and wear.
INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to the neutral position.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (Dimension B).
| *a | Tread Center Mark |
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.
Measure the distance between the tread center marks on the front side of the wheels (Dimension A).
|
Front of the Vehicle |
| Model | Tire Size | Specified Condition |
|---|---|---|
| Except for Rough Road Package | 175/70 R14 | B-A: 1.2 +/- 2.0 mm
(0.0472 +/- 0.0787 in.) |
| 175/65 R15 | B-A: 1.2 +/- 2.0 mm
(0.0472 +/- 0.0787 in.) |
|
| 175/65 R14 | B-A: 1.3 +/- 2.0 mm
(0.0512 +/- 0.0787 in.) |
|
| 185/60 R15 | B-A: 1.3 +/- 2.0 mm
(0.0512 +/- 0.0787 in.) |
|
| Rough Road Package | 175/65 R14 | B-A: 1.3 +/- 2.0 mm
(0.0512 +/- 0.0787 in.) |
| 185/60 R15 | B-A: 1.4 +/- 2.0 mm
(0.0551 +/- 0.0787 in.) |
If the toe-in is not within the specified value, adjust it at the rack ends.
INSPECT CAMBER (REAR WHEEL ALIGNMENT)
Install the camber-caster-kingpin gauge and position the rear wheel on the alignment tester.
Inspect the camber.
| Model | Tire Size | Camber | Right - Left Error |
|---|---|---|---|
| Except for Rough Road Package | 175/70 R14 | -0°57' +/- 30'
(-0.95° +/- 0.5°) |
0°30'
(0.5°) |
| 175/65 R15 | -0°57' +/- 30'
(-0.95° +/- 0.5°) |
0°30'
(0.5°) |
|
| 175/65 R14 | -0°57' +/- 30'
(-0.95° +/- 0.5°) |
0°30'
(0.5°) |
|
| 185/60 R15 | -0°57' +/- 30'
(-0.95° +/- 0.5°) |
0°30'
(0.5°) |
|
| Rough Road Package | 175/65 R14 | -0°54' +/- 30'
(-0.90° +/- 0.5°) |
0°30'
(0.5°) |
| 185/60 R15 | -0°54' +/- 30'
(-0.90° +/- 0.5°) |
0°30'
(0.5°) |
The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both cambers. If the camber is not within the specified range, inspect the suspension parts and replace them if necessary.
INSPECT TOE-IN (REAR WHEEL ALIGNMENT)
|
Front |
| Model | Tire Size | B - A |
|---|---|---|
| Except for Rough Road Package | 175/70 R14 | 3.8 +/- 3.0 mm
(0.150 +/- 0.118 in.) |
| 175/65 R15 | 3.8 +/- 3.0 mm
(0.150 +/- 0.118 in.) |
|
| 175/65 R14 | 3.4 +/- 3.0 mm
(0.134 +/- 0.118 in.) |
|
| 185/60 R15 | 3.6 +/- 3.0 mm
(0.142 +/- 0.118 in.) |
|
| Rough Road Package | 175/65 R14 | 2.7 +/- 3.0 mm
(0.106 +/- 0.118 in.) |
| 185/60 R15 | 2.8 +/- 3.0 mm
(0.110 +/- 0.118 in.) |
If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.