2011-2018 Yaris Service Manual
1NZ-FE · 2NZ-FE
Trouble codes (1252)
- P0010Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic)
- P0010Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0031Air fuel ratio sensor heater current less than 0.8 A, even when the air fuel ratio sensor heater duty cycle...
- P0031Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0031Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0032Air fuel ratio sensor heater current reaches the high limit (Hybrid IC high current limiter monitor input...
- P0032Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic)
- P0032Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic).
- P0037Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0037Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating. (1 trip...
- P0038Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic)
- P0038Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic).
- P0038Heated oxygen sensor heater current reaches high limit (Hybrid IC high current limiter monitor input "Fail")...
- P0100Mass air flow meter voltage less than 0.2 V or more than 4.9 V for 3 seconds (1 trip detection logic)
- P0102Mass air flow meter voltage less than 0.2 V for 3 seconds (1 trip detection logic)
- P0102The mass air flow meter voltage is less than 0.2 V for 3 seconds. (1 trip detection logic: Engine speed is...
- P0103Mass air flow meter voltage more than 4.9 V for 3 seconds (1 trip detection logic)
- P0103The mass air flow meter voltage is more than 4.9 V for 3 seconds. (1 trip detection logic: Engine speed is...
- P0110Open or short in intake air temperature circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116Either condition is met (2 trip detection logic): · When engine is started cold and warmed up, the engine...
- P0116Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a)...
- P0116Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a)...
- P0116Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a)...
- P0117Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0117Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0120Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0120Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip...
- P0121Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip...
- P0122Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0122Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0123Output voltage of VTA1 is 4.535 V or more for 2 seconds or more when the accelerator pedal is depressed (1...
- P0123Output voltage of VTA1 is 4.535 V or more for 2 seconds or more when the accelerator pedal is depressed (1...
- P0130Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm...
- P0130Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm...
- P0130Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm...
- P0132Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
- P0132Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
- P0132Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
- P0133While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich...
- P0133While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich...
- P0133While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich...
- P0134Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions...
- P0134Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions...
- P0134Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions...
- P0136Abnormal voltage output: During active air-fuel ratio control, the following conditions (a) and (b) are met...
- P0136Following conditions (a) and (b) met for 6 minutes or more after engine warmed up (2 trip detection logic):...
- P0136Following conditions (a) and (b) met for 6 minutes or more after engine warmed up (2 trip detection logic):...
- P0136Following conditions (a) and (b) met for 6 minutes or more after engine warmed up (2 trip detection logic):...
- P0137Low voltage (open): During active air-fuel ratio control, the following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air-fuel ratio control, the following conditions (a) and (b) are met for...
- P0171When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean...
- P0171When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean...
- P0171When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean...
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich...
- P0172When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich...
- P0172When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond both lower and upper malfunction thresholds for 2 seconds...
- P0220Output voltage of VTA2 quickly fluctuates beyond both lower and upper malfunction thresholds for 2 seconds...
- P0222Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0222Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0223Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the...
- P0223Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0327Output voltage of knock sensor 0.5 V or less for 1 second or more (1 trip detection logic)
- P0327Output voltage of knock sensor 0.5 V or less for 1 second or more (1 trip detection logic)
- P0328Output voltage of knock sensor 4.5 V or more for 1 second or more (1 trip detection logic)
- P0328Output voltage of knock sensor 4.5 V or more for 1 second or more (1 trip detection logic)
- P0335Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1...
- P0335Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1...
- P0335Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip...
- P0420The ratio of the signal lengths (the signal length of heated oxygen sensor (sensor 2) divided by the signal...
- P0420The ratio of the signal lengths (the signal length of heated oxygen sensor (sensor 2) divided by the signal...
- P0420The ratio of the signal lengths (the signal length of heated oxygen sensor (sensor 2) divided by the signal...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic) (a) The target control value...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic) (a) The target control value...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic) (a) The target control value...
- P0500While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM. (1 trip detection logic:...
- P0500While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM. (1 trip detection logic:...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0560Open in ECM back-up power source circuit (1 trip detection logic)
- P0560Open in ECM back-up power source circuit (1 trip detection logic)
- P0604ECM RAM errors (Main CPU and sub CPU mirroring failure) (1 trip detection logic).
- P0606Either condition is met (1 trip detection logic): · There is an ECM main CPU error. · There is an ECM sub CPU...
- P060AA CPU reset is performed after one of the following conditions is met (1 trip detection logic): · There is an...
- P060BThere is an ECM main CPU communication error (1 trip detection logic).
- P060DEither condition is met (1 trip detection logic): · There is an ECM main CPU error. · There is an ECM sub CPU...
- P060EEither condition is met (1 trip detection logic): · There is an ECM main CPU error. · There is an ECM sub CPU...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0630Either of the following conditions is met (1 trip detection logic): · The VIN is not stored in the ECM. · The...
- P0657There is a throttle actuator power supply error (1 trip detection logic).
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P101DThe heater current is higher than a specified value while the heater is not operating. (1 trip detection...
- P102DThe heated oxygen sensor heater current is higher than a specified value while the heater is not operating....
- P1603After monitoring for startability problems (P1604) finishes and 2 seconds or more have elapsed after starting...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more have elapsed after starting...
- P1604Either condition is met. (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1604Either condition is met. (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1604Either conditions is met (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1604Either conditions is met (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605When idling with the accelerator pedal released and the vehicle stopped, this item detects when the...
- P1605When idling with the accelerator pedal released and the vehicle stopped, this item detects when the...
- P1607ECM CPUs malfunction (1 trip detection logic)
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of the following conditions is met (1 trip detection logic): · Hybrid IC diagnosis signal failure ·...
- P2103Either of the following conditions is met (1 trip detection logic): · Hybrid IC diagnosis signal failure ·...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2118Open in electronic throttle control system power source (+BM) circuit (1 trip detection logic)
- P2118Open in electronic throttle control system power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2122VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2122VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2123VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2123VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed (1 trip detection logic)
- P2127VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more...
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more...
- P2135Either of the following conditions is met (1 trip detection logic): (a) Difference between the output...
- P2135Either of the following conditions is met (1 trip detection logic): (a) Difference between the output...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip...
- P2195Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip...
- P2195Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip...
- P2196Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip...
- P2196Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2238· Case 1 Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic) (a) Voltage at...
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic)
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic)
- P2A00The calculated value for the air-fuel ratio sensor response rate deterioration level is less than the...
- P0010Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic)
- P0010Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0011Valve timing is not adjusted in valve timing advance range (1 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0012Valve timing is not adjusted in valve timing retard range (2 trip detection logic)
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0016Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection...
- P0031Air fuel ratio sensor heater current less than 0.8 A, even when the air fuel ratio sensor heater duty cycle...
- P0031Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0031Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0032Air fuel ratio sensor heater current reaches the high limit (Hybrid IC high current limiter monitor input...
- P0032Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic)
- P0032Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic)
- P0037Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0037Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip...
- P0037Heated oxygen sensor heater current is the specified value or less while the heater is operating. (1 trip...
- P0038Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic)
- P0038Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic)
- P0038Heated oxygen sensor heater current reaches high limit (Hybrid IC high current limiter monitor input "Fail")...
- P0100Mass air flow meter voltage less than 0.2 V, or more than 4.9 V for 3 seconds (1 trip detection logic)
- P0102Mass air flow meter voltage less than 0.2 V for 3 seconds (1 trip detection logic)
- P0102The mass air flow meter voltage is less than 0.2 V for 3 seconds. (1 trip detection logic: Engine speed is...
- P0103Mass air flow meter voltage more than 4.9 V for 3 seconds (1 trip detection logic)
- P0103The mass air flow meter voltage is more than 4.9 V for 3 seconds. (1 trip detection logic: Engine speed is...
- P0110Open or short in intake air temperature circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0112Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0113Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0115Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0116Either condition is met (2 trip detection logic): · When engine is started cold and warmed up, the engine...
- P0116Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a)...
- P0116Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a)...
- P0116Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a)...
- P0117Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0117Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0118Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
- P0120Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0120Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip...
- P0121Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip...
- P0122Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0122Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0123Output voltage of VTA1 is 4.535 V or more for 2 seconds or more when the accelerator pedal is depressed (1...
- P0123Output voltage of VTA1 is 4.535 V or more for 2 seconds or more when the accelerator pedal is depressed (1...
- P0130Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm...
- P0130Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm...
- P0130Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm...
- P0132Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
- P0132Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
- P0132Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
- P0133While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich...
- P0133While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich...
- P0133While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich...
- P0134Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions...
- P0134Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions...
- P0134Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions...
- P0136Abnormal voltage output: During active air-fuel ratio control, the following conditions (a) and (b) are met...
- P0136Following conditions (a) and (b) met for 4 minutes or more after engine warmed up (2 trip detection logic):...
- P0136Following conditions (a) and (b) met for 4 minutes or more after engine warmed up (2 trip detection logic):...
- P0136Following conditions (a) and (b) met for 4 minutes or more after engine warmed up (2 trip detection logic):...
- P0137Low voltage (open): During active air-fuel ratio control, the following conditions (a) and (b) are met for a...
- P0138High voltage (short): During active air-fuel ratio control, the following conditions (a) and (b) are met for...
- P0171When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean...
- P0171When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean...
- P0171When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean...
- P0171With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip...
- P0172When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich...
- P0172When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich...
- P0172When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich...
- P0172With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip...
- P0220Output voltage of VTA2 quickly fluctuates beyond both lower and upper malfunction thresholds for 2 seconds...
- P0220Output voltage of VTA2 quickly fluctuates beyond both lower and upper malfunction thresholds for 2 seconds...
- P0222Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0222Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0223Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the...
- P0223Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0300When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0301When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0302When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0303When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0304When one of following conditions is detected (2 trip detection logic): · High temperature misfire occurs in...
- P0327Output voltage of knock sensor 0.5 V or less for 1 second or more (1 trip detection logic)
- P0327Output voltage of knock sensor 0.5 V or less for 1 second or more (1 trip detection logic)
- P0328Output voltage of knock sensor 4.5 V or more for 1 second or more (1 trip detection logic)
- P0328Output voltage of knock sensor 4.5 V or more for 1 second or more (1 trip detection logic)
- P0335Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1...
- P0335Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1...
- P0335Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more: (1...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0340When one of following conditions is met: · No camshaft position sensor signal to ECM while cranking (2 trip...
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0351No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0352No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0353No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0354No IGF signal to ECM while engine running (1 trip detection logic)
- P0420The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip...
- P0420The ratio of the signal lengths (the signal length of oxygen sensor 2 divided by the signal length of oxygen...
- P0420The ratio of the signal lengths (the signal length of oxygen sensor 2 divided by the signal length of oxygen...
- P0420The ratio of the signal lengths (the signal length of oxygen sensor 2 divided by the signal length of oxygen...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic) (a) The target control value...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic) (a) The target control value...
- P0443Both of the following conditions (a) and (b) are met (1 trip detection logic) (a) The target control value...
- P0500While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM. (1 trip detection logic:...
- P0500While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM. (1 trip detection logic:...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0504Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch ON (b)...
- P0560Open in ECM back-up power source circuit (1 trip detection logic)
- P0560Open in ECM back-up power source circuit (1 trip detection logic)
- P0604ECM RAM errors (Main CPU and sub CPU mirroring failure) (1 trip detection logic).
- P0606Either condition is met (1 trip detection logic): · There is an ECM main CPU error. · There is an ECM sub CPU...
- P060AA CPU reset is performed after one of the following conditions is met (1 trip detection logic): · There is an...
- P060BThere is an ECM main CPU communication error (1 trip detection logic).
- P060DEither condition is met (1 trip detection logic): · There is an ECM main CPU error. · There is an ECM sub CPU...
- P060EEither condition is met (1 trip detection logic): · There is an ECM main CPU error. · There is an ECM sub CPU...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0630Either of the following conditions is met (1 trip detection logic): · The VIN is not stored in the ECM. · The...
- P0657There is a throttle actuator power supply error (1 trip detection logic).
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P0724Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86...
- P101DThe heater current is higher than a specified value while the heater is not operating. (1 trip detection...
- P102DThe heated oxygen sensor heater current is higher than a specified value while the heater is not operating....
- P1603After monitoring for startability problems (P1604) finishes and 2 seconds or more have elapsed after starting...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more have elapsed after starting...
- P1604Either condition is met. (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1604Either condition is met. (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1604Either conditions is met (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1604Either conditions is met (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605When idling with the accelerator pedal released and the vehicle stopped, this item detects when the...
- P1605When idling with the accelerator pedal released and the vehicle stopped, this item detects when the...
- P1607ECM CPUs malfunction (1 trip detection logic)
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2102Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio...
- P2103Either of the following conditions is met (1 trip detection logic): · Hybrid IC diagnosis signal failure ·...
- P2103Either of the following conditions is met (1 trip detection logic): · Hybrid IC diagnosis signal failure ·...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2109The ISC learned value is approximately 3 times larger than normal even though the actual intake air amount...
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2111ECM signals throttle actuator to close, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2112ECM signals throttle actuator to open, but the actuator is stuck (1 trip detection logic)
- P2118Open in electronic throttle control system power source (+BM) circuit (1 trip detection logic)
- P2118Open in electronic throttle control system power source (+BM) circuit (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2119Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2120VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2121Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic) 1. Difference between VPA...
- P2122VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2122VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
- P2123VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2123VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic)
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2125VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed (1 trip detection logic)
- P2127VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed (1 trip detection logic)
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more...
- P2128Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more...
- P2135Either of the following conditions is met (1 trip detection logic): (a) Difference between the output...
- P2135Either of the following conditions is met (1 trip detection logic): (a) Difference between the output...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2138Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA...
- P2195Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2195Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip...
- P2195Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip...
- P2195Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip...
- P2196Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor...
- P2196Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip...
- P2196Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip...
- P2196Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip...
- P2237An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is...
- P2238· Case 1 Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic) (a) Voltage at...
- P2239The A1A+ voltage is higher than 4.5 V (2 trip detection logic)
- P2252The A1A- voltage is 0.5 V or less (2 trip detection logic).
- P2253The A1A- voltage is higher than 4.5 V (2 trip detection logic).
- P2610ECM internal malfunction (2 trip detection logic)
- P2A00The calculated value for the air-fuel ratio sensor response rate deterioration level is less than the...
- P0500The vehicle speed signal from the skid control ECU is cut for 0.14 seconds or more while cruise control is in...
- P0500The vehicle speed signal from the skid control ECU is cut for 0.14 seconds or more while cruise control is in...
- P0503A malfunction in the vehicle speed signal is detected while cruise control is in operation.
- P0503A malfunction in the vehicle speed signal is detected while cruise control is in operation.
- P0571The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
- P0571The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
- P0571The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
- P0575Either condition is met: · The cruise control input signal is abnormal. · The stop light switch input signal...
- P0575Either condition is met: · The cruise control input signal is abnormal. · The stop light switch input signal...
- C1A47Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA0Pre-crash safety city sensor detects an internal malfunction.
- C1AA3Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA4Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA5Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA8The beam axis of the monocular camera sensor or any of the laser sensors built into the pre-crash safety city...
- C1AAAAll of the following conditions are met: - The battery voltage is 10 V or more. - The vehicle is being driven...
- U0100Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- U0123All of the following conditions are met: - 3 seconds have elapsed since the ignition switch was turned ON. -...
- U0126All of the following conditions are met: - 3 seconds have elapsed since the ignition switch was turned ON. -...
- U0129All of the following conditions are met: - 3 seconds have elapsed since the ignition switch was turned ON. -...
- U0155All of the following conditions are met: - 3 seconds have elapsed since the ignition switch was turned ON. -...
- P0705One of the following conditions (A), (B) or (C) is met
- P0705one of the following conditions (A), (B) or (C) is met
- P0705one of the following conditions (A), (B) or (C) is met
- P0711Either of following Condition (A) or (B) is met
- P0711Either of following Condition (A) or (B) is met
- P0712ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more (1 trip detection logic).
- P0712ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more (1 trip detection logic).
- P0713Following condition continues for 0.5 seconds or more (1 trip detection logic) ATF temperature sensor...
- P0713Following condition continues for 0.5 seconds or more (1 trip detection logic) ATF temperature sensor...
- P0717All conditions below are detected for 5 seconds or more (1 trip detection logic). (a) Gear change is not...
- P0717All conditions below are detected for 5 seconds or more (1 trip detection logic). (a) Gear change is not...
- P0741(a) Lock-up does not occur when driving in lock-up range or lock-up remains ON in lock-up OFF range. (2 trip...
- P0741(a) Lock-up does not occur when driving in lock-up range or lock-up remains ON in lock-up OFF range. (2 trip...
- P0751S1 stuck OFF malfunction*1: ECM determines there is malfunction when both of following conditions are met (2...
- P0751S1 stuck OFF malfunction*1: ECM determines there is malfunction when both of following conditions are met (2...
- P0756S2 stuck OFF malfunction*1: Shifting to 1st and 4th gears is impossible. ECM determines that there is...
- P0756S2 stuck OFF malfunction*1: Shifting to 1st and 4th gears is impossible. ECM determines that there is...
- P0787ECM detects short in solenoid valve ST circuit 4 times when solenoid valve ST is operated (1 trip detection...
- P0787ECM detects short in solenoid valve ST circuit 4 times when solenoid valve ST is operated (1 trip detection...
- P0788ECM detects open in solenoid valve ST circuit 4 times when solenoid valve ST is not operated (1 trip...
- P0788ECM detects open in solenoid valve ST circuit 4 times when solenoid valve ST is not operated (1 trip...
- P0973ECM detects short in solenoid valve S1 circuit 4 times when solenoid valve S1 is operated (1 trip detection...
- P0973ECM detects short in solenoid valve S1 circuit 4 times when solenoid valve S1 is operated (1 trip detection...
- P0974ECM detects open in solenoid valve S1 circuit 4 times when solenoid valve S1 is not operated (1 trip...
- P0974ECM detects open in solenoid valve S1 circuit 4 times when solenoid valve S1 is not operated (1 trip...
- P0976ECM detects short in solenoid valve S2 circuit 4 times when solenoid valve S2 is operated (1 trip detection...
- P0976ECM detects short in solenoid valve S2 circuit 4 times when solenoid valve S2 is operated (1 trip detection...
- P0977ECM detects open in solenoid valve S2 circuit 4 times when solenoid valve S2 is not operated (1 trip...
- P0977ECM detects open in solenoid valve S2 circuit 4 times when solenoid valve S2 is not operated (1 trip...
- P2714ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output...
- P2714ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2769ECM detects short in solenoid valve SL circuit when solenoid valve SL operated. (Solenoid resistance: 8 Ω or...
- P2769ECM detects short in solenoid valve SL circuit when solenoid valve SL operated. (Solenoid resistance: 8 Ω or...
- P2770ECM detects open in solenoid valve SL circuit when solenoid valve SL not operated. (Solenoid resistance: 100...
- P2770ECM detects open in solenoid valve SL circuit when solenoid valve SL not operated. (Solenoid resistance: 100...
- P0705One of the following conditions (A), (B) or (C) is met
- P0705One of the following conditions (A), (B) or (C) is met
- P0705One of the following conditions (A), (B) or (C) is met
- P0711Either of following Condition (A) or (B) is met
- P0711Either of following Condition (A) or (B) is met
- P0712ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more (1 trip detection logic).
- P0712ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more (1 trip detection logic).
- P0713Following condition continues for 0.5 seconds or more (1 trip detection logic) ATF temperature sensor...
- P0713Following condition continues for 0.5 seconds or more (1 trip detection logic) ATF temperature sensor...
- P0717All conditions below are detected for 5 seconds or more (1 trip detection logic). (a) Gear change is not...
- P0717All conditions below are detected for 5 seconds or more (1 trip detection logic). (a) Gear change is not...
- P0741(a) Lock-up does not occur when driving in lock-up range or lock-up remains ON in lock-up OFF range. (2 trip...
- P0741(a) Lock-up does not occur when driving in lock-up range or lock-up remains ON in lock-up OFF range. (2 trip...
- P0751S1 stuck OFF malfunction*1: ECM determines there is malfunction when both of following conditions are met (2...
- P0751S1 stuck OFF malfunction*1: ECM determines there is malfunction when both of following conditions are met (2...
- P0756S2 stuck OFF malfunction*1: Shifting to 1st and 4th gears is impossible. ECM determines that there is...
- P0756S2 stuck OFF malfunction*1: Shifting to 1st and 4th gears is impossible. ECM determines that there is...
- P0787ECM detects short in solenoid valve ST circuit 4 times when solenoid valve ST is operated (1 trip detection...
- P0787ECM detects short in solenoid valve ST circuit 4 times when solenoid valve ST is operated (1 trip detection...
- P0788ECM detects open in solenoid valve ST circuit 4 times when solenoid valve ST is not operated (1 trip...
- P0788ECM detects open in solenoid valve ST circuit 4 times when solenoid valve ST is not operated (1 trip...
- P0973ECM detects short in solenoid valve S1 circuit 4 times when solenoid valve S1 is operated (1 trip detection...
- P0973ECM detects short in solenoid valve S1 circuit 4 times when solenoid valve S1 is operated (1 trip detection...
- P0974ECM detects open in solenoid valve S1 circuit 4 times when solenoid valve S1 is not operated (1 trip...
- P0974ECM detects open in solenoid valve S1 circuit 4 times when solenoid valve S1 is not operated (1 trip...
- P0976ECM detects short in solenoid valve S2 circuit 4 times when solenoid valve S2 is operated (1 trip detection...
- P0976ECM detects short in solenoid valve S2 circuit 4 times when solenoid valve S2 is operated (1 trip detection...
- P0977ECM detects open in solenoid valve S2 circuit 4 times when solenoid valve S2 is not operated (1 trip...
- P0977ECM detects open in solenoid valve S2 circuit 4 times when solenoid valve S2 is not operated (1 trip...
- P2714ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output...
- P2714ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2716Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip...
- P2769ECM detects short in solenoid valve SL circuit when solenoid valve SL operated. (Solenoid resistance: 8 Ω or...
- P2769ECM detects short in solenoid valve SL circuit when solenoid valve SL operated. (Solenoid resistance: 8 Ω or...
- P2770ECM detects open in solenoid valve SL circuit when solenoid valve SL not operated. (Solenoid resistance: 100...
- P2770ECM detects open in solenoid valve SL circuit when solenoid valve SL not operated. (Solenoid resistance: 100...
- C1203Engine, drive source and destination variations that are sent from the ECM or main body ECU (multiplex...
- C1203Engine, drive source and destination variations that are sent from the ECM or main body ECU (multiplex...
- C1241When any of the following is detected: 1. At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal...
- C1271Detected only during Test Mode.
- C1271Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1273Detected only during Test Mode.
- C1273Detected only during Test Mode.
- C1274Detected only during Test Mode.
- C1274Detected only during Test Mode.
- C1275Detected only during Test Mode.
- C1276Detected only during Test Mode.
- C1277Detected only during Test Mode.
- C1278Detected only during Test Mode.
- C1401Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1401Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1402Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1402Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1403Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1403Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1404Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1404Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1405Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1406Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1407Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1408Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1413Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1414Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1415Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1416Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1417The IG1 terminal voltage is 17.4 V or more for 0.8 seconds or more.
- C1425When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body...
- C1427Actuator pump motor does not operate properly.
- C1428With the ABS motor relay OFF and the ABS motor fail safe relay ON, an open in the motor circuit continues for...
- C1468Open or short in the solenoid circuit continues for 0.05 seconds or more.
- C1469Open or short in the solenoid circuit continues for 0.05 seconds or more.
- C146AOpen or short in the solenoid circuit continues for 0.05 seconds or more.
- C146BOpen or short in the solenoid circuit continues for 0.05 seconds or more.
- C146CWhen either of the following is detected: 1. All of the following conditions continue for 0.12 seconds or...
- C146DWhen the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
- C146EWhen either of the following is detected: 1. Both of the following conditions continue for 0.22 seconds or...
- C146FImmediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4 seconds...
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0142No communication with main body ECU
- U0142No communication with main body ECU(multiplex network body ECU)
- C1201Engine control system malfunction signal continues for 1 second or more.
- C1201Engine control system malfunction signal continues for 1 second or more.
- C1203Engine, drive source and destination variations that are sent from the ECM do not match the ones of the skid...
- C1203Engine, drive source and destination variations that are sent from the ECM or main body ECU (multiplex...
- C1203Engine, drive source and destination variations that are sent from the ECM or main body ECU (multiplex...
- C1210Zero point calibration of yaw rate sensor undone.
- C1210Zero point calibration of yaw rate sensor undone.
- C1225When any of the following is detected: 1. While outputting switching solenoid (SM1 or SM2) ON, overcurrent...
- C1225When any of the following is detected: 1. While outputting switching solenoid (SM1 or SM2) ON, overcurrent...
- C1232At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30...
- C1232At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30...
- C1232At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30...
- C1232At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30...
- C1241When any of the following is detected: 1. At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal...
- C1241When any of the following is detected: 1. At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal...
- C1243While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1...
- C1243While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1...
- C1243While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1...
- C1243While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1...
- C1245At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated...
- C1245At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated...
- C1245At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated...
- C1245At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated...
- C1271Detected only during Test Mode.
- C1271Detected only during Test Mode.
- C1271Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1272Detected only during Test Mode.
- C1273Detected only during Test Mode.
- C1273Detected only during Test Mode.
- C1273Detected only during Test Mode.
- C1274Detected only during Test Mode.
- C1274Detected only during Test Mode.
- C1274Detected only during Test Mode.
- C1275Detected only during Test Mode.
- C1275Detected only during Test Mode.
- C1276Detected only during Test Mode.
- C1276Detected only during Test Mode.
- C1277Detected only during Test Mode.
- C1277Detected only during Test Mode.
- C1278Detected only during Test Mode.
- C1278Detected only during Test Mode.
- C1279Detected only during Test Mode.
- C1279Detected only during Test Mode.
- C1279Detected only during Test Mode.
- C1279Detected only during Test Mode.
- C1281Detected only during Test Mode.
- C1281Detected only during Test Mode.
- C1290The steering angle sensor zero point calibration position vastly differs from the recorded value.
- C1290The steering angle sensor zero point calibration position vastly differs from the recorded value.
- C1290The steering angle sensor zero point calibration position vastly differs from the recorded value.
- C1336Zero point calibration of acceleration sensor undone.
- C1336Zero point calibration of acceleration sensor undone.
- C1361Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the...
- C1361Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the...
- C1381At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is...
- C1381At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is...
- C1401Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1401Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1401Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1402Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1402Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1402Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1403Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1403Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1403Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1404Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1404Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1404Any of the following is detected: 1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one...
- C1405Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1405Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1406Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1406Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1407Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1407Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1408Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1408Either of the following is detected: 1. An open in the speed sensor signal circuit continues for 0.5 seconds...
- C1413Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1413Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1414Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1414Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1415Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1415Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1416Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1416Any of the following is detected: 1. An open in the sensor signal circuit of a malfunctioning area occurs 255...
- C1417The IG1 terminal voltage is 17.4 V or more for 0.8 seconds or more.
- C1417The IG1 terminal voltage is 17.4 V or more for 0.8 seconds or more.
- C1419A data malfunction signal is received from the acceleration sensor.
- C1419A data malfunction signal is received from the acceleration sensor.
- C1420After the difference between GL1 and GL2 becomes 0.6 G or more with the vehicle stationary, the difference...
- C1420After the difference between GL1 and GL2 becomes 0.6 G or more with the vehicle stationary, the difference...
- C1421Either of the following is detected: 1. With the IG1 terminal voltage between 9.5 and 17.4 V, the VCM...
- C1421Either of the following is detected: 1. With the IG1 terminal voltage between 9.5 and 17.4 V, the VCM...
- C1422When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
- C1422When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
- C1422When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
- C1422When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
- C1423The PMC terminal voltage is less than 0.27 V for 5 seconds or more.
- C1423The PMC terminal voltage is less than 0.27 V for 5 seconds or more.
- C1424Any of the following is detected: 1. Noise occurs in the PMC terminal 7 times or more within 5 seconds. 2....
- C1424Any of the following is detected: 1. Noise occurs in the PMC terminal 7 times or more within 5 seconds. 2....
- C1425When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body...
- C1425When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body...
- C1425When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body...
- C1425When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body...
- C1426After a stuck judgement* has been made within 10 minutes of stopping the vehicle, then after driving at a...
- C1427Actuator pump motor does not operate properly.
- C1427Actuator pump motor does not operate properly.
- C1428With the ABS motor relay OFF and the ABS motor fail safe relay ON, an open in the motor circuit continues for...
- C1428With the ABS motor relay OFF and the ABS motor fail safe relay ON, an open in the motor circuit continues for...
- C1432Steering angle sensor power supply malfunction signal is received from steering angle sensor.
- C1432Steering angle sensor power supply malfunction signal is received from steering angle sensor.
- C1433With the IG1 terminal voltage 9.5 to 17.4 V, the skid control ECU receives an error signal from the steering...
- C1433With the IG1 terminal voltage 9.5 to 17.4 V, the skid control ECU receives an error signal from the steering...
- C1434Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle...
- C1434Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle...
- C1434Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle...
- C1434Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle...
- C1435A data malfunction signal is received from the yaw rate sensor.
- C1435A data malfunction signal is received from the yaw rate sensor.
- C1436Either of the following is detected: 1. With the vehicle stationary, the yaw rate and deceleration sensor...
- C1436Either of the following is detected: 1. With the vehicle stationary, the yaw rate and deceleration sensor...
- C1437When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot...
- C1437When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot...
- C1437When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot...
- C1437When the IG1 terminal voltage is 10 V or more and the vehicle speed is 15 km/h (9 mph) or more, data cannot...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1440Driving at a steep bank angle
- C1440Driving at a steep bank angle
- C1442Both of the following is condition is met. 1. With the IG1 terminal voltage between 9.5 and 17.4 V. 2. An...
- C1442Both of the following is condition is met. 1. With the IG1 terminal voltage between 9.5 and 17.4 V. 2. An...
- C1443Both of the following is condition is met. 1. With the IG1 terminal voltage between 9.5 and 17.4 V. 2. An...
- C1443Both of the following is condition is met. 1. With the IG1 terminal voltage between 9.5 and 17.4 V. 2. An...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1468Open or short in the solenoid circuit continues for 0.05 seconds or more.
- C1468Open or short in the solenoid circuit continues for 0.05 seconds or more.
- C1469Open or short in the solenoid circuit continues for 0.05 seconds or more.
- C1469Open or short in the solenoid circuit continues for 0.05 seconds or more.
- C146AOpen or short in the solenoid circuit continues for 0.05 seconds or more.
- C146AOpen or short in the solenoid circuit continues for 0.05 seconds or more.
- C146BOpen or short in the solenoid circuit continues for 0.05 seconds or more.
- C146BOpen or short in the solenoid circuit continues for 0.05 seconds or more.
- C146CWhen either of the following is detected: 1. All of the following conditions continue for 0.12 seconds or...
- C146CWhen either of the following is detected: 1. All of the following conditions continue for 0.12 seconds or...
- C146DWhen the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
- C146DWhen the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
- C146EWhen either of the following is detected: 1. Both of the following conditions continue for 0.22 seconds or...
- C146EWhen either of the following is detected: 1. Both of the following conditions continue for 0.22 seconds or...
- C146FImmediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4 seconds...
- C146FImmediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4 seconds...
- C1473Detected only during Test Mode.
- C1473Detected only during Test Mode.
- C1473Detected only during Test Mode.
- C1473Detected only during Test Mode.
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0073When any of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0100When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed 15 km/h (9 mph) or more, data...
- U0100When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed 15 km/h (9 mph) or more, data...
- U0100When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed 15 km/h (9 mph) or more, data...
- U0100When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed 15 km/h (9 mph) or more, data...
- U0100When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more,...
- U0123When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0123When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0124When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, and the...
- U0124When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, and the...
- U0124When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, and the...
- U0124When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0124When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0126When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0126When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0126When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0126When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0126When either of the following is detected: 1. When the IG1 terminal voltage is between 10 and 17.4 V, data...
- U0142No communication with main body ECU
- U0142No communication with main body ECU
- U0142No communication with main body ECU
- C1511Torque Sensor1
- C1512Torque Sensor2
- C1513C1513
- C1514Torque Sensor Power Supply Voltage
- C1515Torque sensor zero point calibration not performed.
- C1515Torque sensor zero point calibration not performed.
- C1516Torque sensor zero point calibration not completed successfully.
- C1516Torque sensor zero point calibration not completed successfully.
- C1517Torque Hold
- C1524Short (or open) in motor circuit or abnormal voltage or current in motor circuit.
- C1531ECU internal malfunction (CPU malfunction)
- C1531ECU internal malfunction (CPU malfunction)
- C1532ECU internal malfunction (Peripheral circuit malfunction)
- C1532ECU internal malfunction (Peripheral circuit malfunction)
- C1533ECU internal malfunction (Substrate temperature sensor malfunction)
- C1533ECU internal malfunction (Substrate temperature sensor malfunction)
- C1534ECU internal malfunction (EEPROM error)
- C1534ECU internal malfunction (EEPROM error)
- C1535ECU internal malfunction (Steering wheel location data error)
- C1535ECU internal malfunction (Steering wheel location data error)
- C1541Vehicle Speed Signal Abnormal Increase
- C1542Vehicle Speed Signal Abnormal Decrease
- C1551Open or short in IG power source circuit with ignition switch ON.
- C1552PIG power source circuit malfunction
- C1553· PIG power source overvoltage · IG power source overvoltage
- C1554Power source relay circuit malfunction
- C1555Motor relay circuit malfunction.
- C1571Speed sensor malfunction (Test mode).
- C1581Assist map not written in power steering ECU assembly
- C1581Assist map not written in power steering ECU assembly
- C1581Assist map not written in power steering ECU assembly
- C1582Assist map number mismatch
- C1582Assist map number mismatch
- U0100ECM communication error
- U0100ECM communication error
- U0100ECM communication error
- U0129Skid control ECU communication error
- U0129Skid control ECU communication error
- U0129Skid control ECU communication error
- B1579Telephone microphone signal is lost.
- B1585Either condition is met. · Non mass-storage class or incompatible protocol USB device. · USB device with an...
- B158DThe internal video signal stoppage of the radio and display receiver assembly
- B158FA video or audio signal is interrupted when the battery voltage drops.
- B15A0When either condition below is met: · Bus malfunction · EEPROM error
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When either condition below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner malfunction
- B15B4When either condition below is met: · Mechanism drive signal malfunction · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction.
- B15C3A short is detected in the speaker output circuit.
- B15F6Main body ECU vehicle setting processing error.
- B15F6Main body ECU vehicle setting processing error.
- U0073CAN bus connection error
- U0073CAN bus connection error
- U0100CAN reception error
- U0100CAN reception error
- U0129CAN reception error
- U0129CAN reception error
- U0140CAN reception error
- U0140CAN reception error
- U0155CAN reception error
- U0155CAN reception error
- U0164CAN reception error
- U0164CAN reception error
- B1579Telephone microphone signal is lost.
- B157E"Bluetooth" antenna is not connected
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B158CThe SD card (disc player disc) cannot be mounted when inserted into the SD card (disc player disc) slot
- B158DThe internal video signal of the navigation receiver assembly is interrupted
- B158FA video or audio signal is interrupted when the battery voltage drops.
- B15A0When either of the conditions below is met: · Bus malfunction · EEPROM error
- B15ADWhen any of the following conditions is met: · Short to ground or +B or open occurs in gyro signal circuit ·...
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B4When one of the conditions below is met: · Mechanical communication error · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15C0Navigation antenna error
- B15C1Error of the power source to the navigation antenna
- B15C2A difference between the GPS speed and SPD pulse is detected
- B15C3A short is detected in the speaker output circuit.
- B15F6Main body ECU vehicle setting processing error.
- B15F6Main body ECU vehicle setting processing error.
- U0073CAN bus connection error
- U0073CAN bus connection error
- U0100CAN reception error
- U0100CAN reception error
- U0129CAN reception error
- U0129CAN reception error
- U0140CAN reception error
- U0140CAN reception error
- U0155CAN reception error
- U0155CAN reception error
- U0164CAN reception error
- U0164CAN reception error
- B2321No communication between the power window regulator motor assembly RH (for driver side)*1 or power window...
- B2321No communication between the power window regulator motor assembly RH (for driver side)*1 or power window...
- B2321No communication between the power window regulator motor assembly RH (for driver side)*1 or power window...
- B2325Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the...
- B2325Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the...
- B2325Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the...
- B2780The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip...
- B2780The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip...
- B2784The antenna coil built into the transponder key amplifier is open or shorted (determined by communication...
- B2784The antenna coil built into the transponder key coil is open or shorted (determined by communication with...
- B2793A transponder chip malfunction (1 trip detection logic*).
- B2793A transponder chip malfunction (1 trip detection logic*).
- B2794A key with an incomplete key code is inserted into the ignition key cylinder (1 trip detection logic*).
- B2794A key with an incomplete key code is inserted into the ignition key cylinder (1 trip detection logic*).
- B2795A key with a different vehicle serial number is inserted into the ignition key cylinder (1 trip detection...
- B2795A key with a different vehicle serial number is inserted into the ignition key cylinder (1 trip detection...
- B2796The key code cannot be transmitted (1 trip detection logic*).
- B2796The key code cannot be transmitted (1 trip detection logic*).
- B2797A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
- B2797A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
- B2798Key code identification cannot be completed within the specified time (1 trip detection logic*).
- B2798Key code identification cannot be completed within the specified time (1 trip detection logic*).
- B2799Either condition is met (1 trip detection logic*): · A malfunction occurs in the communication or...
- B2799Either condition is met (1 trip detection logic*): · A malfunction occurs in the communication or...
- B2799Either condition is met (1 trip detection logic*): · A malfunction occurs in the communication or...
- B2799Either condition is met (1 trip detection logic*): · A malfunction occurs in the communication or...
- B279AThe communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output (1...
- B279AThe communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output (1...
- B279AThe communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output (1...
- B279AThe communication line (IMI - EFIO) between the ECM and transponder key ECU assembly is stuck on HI output (1...
- B279CAn ECM that is incompatible with the engine immobiliser system is installed (1 trip detection logic*).
- B1500When combination meter detects fuel sender gauge malfunction
- B1500When combination meter detects fuel sender gauge malfunction
- B1507When IG voltage is 9.5 V or more and the following condition detected: 1. Open in turn signal light circuit
- B1507When IG voltage is 9.5 V or more and the following condition is detected: 1. Open in turn signal light circuit
- B1508When IG voltage is 9.5 V or more and the following condition detected: 1. Short in turn signal light circuit...
- B1508When IG voltage is 9.5 V or more and the following condition is detected: 1. Short in turn signal light...
- U0100ECM communication error
- U0100ECM communication error
- U0100ECM communication error
- U0129Skid control ECU communication error
- U0129Skid control ECU communication error
- U0129Skid control ECU communication error
- U0131Power steering ECU communication error
- U0131Power steering ECU communication error
- U0131Power steering ECU communication error
- U0142Lost Communication with Main Body ECU
- U0151Center airbag sensor communication error
- U0151Center airbag sensor communication error
- U0151Center airbag sensor communication error
- B1000/31 Airbag sensor assembly malfunction
- B161B/1A Either condition is met: · A front airbag sensor malfunction. · A airbag sensor assembly malfunction.
- B161C/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161D/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Driver side...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Driver...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1000/31 Airbag sensor assembly malfunction
- B161B/1A Either condition is met: · A front airbag sensor malfunction. · A airbag sensor assembly malfunction.
- B161C/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161C/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161D/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161D/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1622/81 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1622/81 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1623/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1623/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1627/82 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1627/82 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1628/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1628/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1630/23 When one of following conditions is met: · No. 2 side airbag sensor assembly RH malfunction · Airbag sensor...
- B1630/23 When one of following conditions is met: · No. 2 side airbag sensor assembly RH malfunction · Airbag sensor...
- B1632/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1632/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1635/24 When one of following conditions is met: · No. 2 side airbag sensor assembly LH malfunction · Airbag sensor...
- B1635/24 When one of following conditions is met: · No. 2 side airbag sensor assembly LH malfunction · Airbag sensor...
- B1637/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1637/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1647/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1647/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1690/15 When one of following conditions is met: · Door side airbag sensor RH malfunction · Airbag sensor assembly...
- B1690/15 When one of following conditions is met: · Door side airbag sensor RH malfunction · Airbag sensor assembly...
- B1692/81 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1692/81 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1693/81 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1693/81 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1695/16 When one of following conditions is met: · Door side airbag sensor LH malfunction · Airbag sensor assembly...
- B1695/16 When one of following conditions is met: · Door side airbag sensor LH malfunction · Airbag sensor assembly...
- B1697/82 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1697/82 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1698/82 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1698/82 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Driver side...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Driver side...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Driver...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Driver...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1860/64 · The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib...
- B1860/64 · The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib...
- B1861/64 · The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1861/64 · The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1862/64 · The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1862/64 · The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1863/64 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib...
- B1863/64 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- B1000/31 Airbag sensor assembly malfunction
- B161B/1A Either condition is met: · A front airbag sensor malfunction. · A airbag sensor assembly malfunction.
- B161C/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B161D/9A · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1620/21 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1622/81 · Side airbag sensor assembly RH malfunction · Airbag sensor assembly malfunction
- B1623/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1625/22 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1627/82 · Side airbag sensor assembly LH malfunction · Airbag sensor assembly malfunction
- B1628/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1630/23 When one of following conditions is met: · No. 2 side airbag sensor assembly RH malfunction · Airbag sensor...
- B1632/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1633/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1635/24 When one of following conditions is met: · No. 2 side airbag sensor assembly LH malfunction · Airbag sensor...
- B1637/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1638/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1642/81 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1647/82 · The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to...
- B1690/15 When one of following conditions is met: · Door side airbag sensor RH malfunction · Airbag sensor assembly...
- B1692/81 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1693/81 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1695/16 When one of following conditions is met: · Door side airbag sensor LH malfunction · Airbag sensor assembly...
- B1697/82 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1698/82 When one of following conditions is met: · The airbag sensor assembly receives a line short circuit signal,...
- B1800/51 · The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during...
- B1801/51 · The airbag sensor assembly receives an open circuit signal in the driver side squib circuit. · Driver side...
- B1802/51 · The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit. ·...
- B1803/51 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit. · Driver...
- B1805/52 · The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit...
- B1806/52 · The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·...
- B1807/52 · The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib...
- B1808/52 · The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit....
- B1820/55 · The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary...
- B1821/55 · The airbag sensor assembly receives an open circuit signal in the side squib RH circuit. · Side squib RH...
- B1822/55 · The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit. · Side...
- B1823/55 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit. · Side squib...
- B1825/56 · The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary...
- B1826/56 · The airbag sensor assembly receives an open circuit signal in the side squib LH circuit. · Side squib LH...
- B1827/56 · The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit. · Side...
- B1828/56 · The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit. · Side squib...
- B1830/57 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit...
- B1831/57 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit. ·...
- B1832/57 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH...
- B1833/57 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit. ·...
- B1835/58 · The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit...
- B1836/58 · The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit. ·...
- B1837/58 · The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH...
- B1838/58 · The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit. ·...
- B1860/64 · The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib...
- B1861/64 · The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit. ·...
- B1862/64 · The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib...
- B1863/64 · The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib...
- B1900/73 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit...
- B1901/73 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit. ·...
- B1902/73 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH...
- B1903/73 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH...
- B1905/74 · The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit...
- B1906/74 · The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·...
- B1907/74 · The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH...
- B1908/74 · The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH...
- C1A47Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1A48All of the following conditions are met: - 5 seconds have elapsed since the ignition switch to ON. - The...
- C1A4BAll of the following conditions are met: - 3 seconds have elapsed since the ignition switch to ON. - The...
- C1A50Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1A62Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1A63When the ignition switch to ON, the pre-crash safety city sensor receives a accelerator pedal position sensor...
- C1AA0Pre-crash safety city sensor detects an internal malfunction.
- C1AA3Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA4Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA5Both of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- C1AA7The battery voltage is 9 V or more and either of the following conditions is met: - Voltage at the BUZ...
- C1AA8The beam axis of the monocular camera sensor or any of the laser sensors built into the pre-crash safety city...
- C1AA9All of the following conditions are met: - The battery voltage is 9 V or more. - The vehicle is being driven...
- C1AAAAll of the following conditions are met: - The battery voltage is 10 V or more. - The vehicle is being driven...
- C1AAFEither of the following conditions is met: · When the pre-crash safety city heater receives an operation...
- U0100All of the following conditions are met: - 3 seconds have elapsed since the ignition switch to ON. - The...
- U0100The pre-crash safety city sensor is unable to receive data from the ECM continuously for 9 seconds or more.
- U0123All of the following conditions are met: - 3 seconds have elapsed since the ignition switch to ON. - The...
- U0123The pre-crash safety city sensor is unable to receive data from the ECM continuously for 9 seconds or more.
- U0126All of the following conditions are met: - 3 seconds have elapsed since the ignition switch to ON. - The...
- U0126The pre-crash safety city sensor is unable to receive data from the spiral with sensor cable sub-assembly...
- U0129All of the following conditions are met: - 3 seconds have elapsed since the ignition switch to ON. - The...
- U0129The pre-crash safety city sensor is unable to receive data from the brake actuator assembly (skid control...
- U0155The pre-crash safety city sensor is unable to receive data from the combination meter assembly continuously...
- U023ABoth of the following conditions are met: 1. All of the following conditions are met: - 3 seconds have...
- U023AThe brake actuator assembly (skid control ECU) is unable to receive data from the pre-crash safety city...
- B1411/11 An open or short in the cooler thermistor (room temperature sensor) circuit.
- B1411/11 An open or short in the cooler thermistor (room temperature sensor) circuit.
- B1411/11 An open or short in the cooler thermistor (room temperature sensor) circuit.
- B1412An open or short in the thermistor assembly (ambient temperature sensor) circuit.
- B1412An open or short in the thermistor assembly (ambient temperature sensor) circuit.
- B1412An open or short in the thermistor assembly (ambient temperature sensor) circuit.
- B1412/12 An open or short in the thermistor assembly (ambient temperature sensor) circuit.
- B1413An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.
- B1413An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.
- B1413An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.
- B1413/13 An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.
- B1423Either condition is met: · An open or short in the air conditioner pressure sensor circuit. · Refrigerant...
- B1423Either condition is met: · An open or short in the air conditioner pressure sensor circuit. · Refrigerant...
- B1423Either condition is met: · An open or short in the air conditioner pressure sensor circuit. · Refrigerant...
- B1423/23 Either condition is met: · An open or short in the air conditioner pressure sensor circuit. · Refrigerant...
- B1441/41 The air mix damper position does not change when the air conditioning amplifier assembly operates the No. 1...
- B1442/42 The air inlet servo motor position does not change when the air conditioning amplifier assembly operates the...
- B1443/43 The air outlet servo motor position does not change when the air conditioning amplifier assembly operates the...
- B1451An open or short in the cooler compressor solenoid circuit.
- B1451An open or short in the cooler compressor solenoid circuit.
- B1451An open or short in the cooler compressor solenoid circuit.
- B1451/51 An open or short in the cooler compressor solenoid circuit.
- B1497/97 An open circuit or malfunction in the communication line.
- B14A2A short in the driver side solar sensor circuit.
- B14A2A short in the driver side solar sensor circuit.
- B14A2A short in the driver side solar sensor circuit.
- B14B2Lost communication with the air conditioning control assembly.
- B14B2Lost communication with the air conditioning control assembly.
- B14B8When the following conditions is detected using the refrigerant shortage check in normal operation: The...
- B14B8When the following conditions is detected using the refrigerant shortage check in normal operation: The...
- U0100Lost communication with ECM.
- U0100Lost communication with ECM.
- U0100Lost communication with ECM.
- U0100Lost communication with ECM.
- U0131Lost Communication with power steering ECU assembly.
- U0131Lost Communication with power steering ECU assembly.
- U0131Lost Communication with power steering ECU assembly.
- U0131Lost Communication with power steering ECU assembly.
- U0142Lost Communication with main body ECU.
- U0142Lost Communication with main body ECU.
- U0142Lost Communication with main body ECU.
- U0142Lost Communication with main body ECU.
- U0155Lost Communication with combination meter assembly.
- U0155Lost Communication with combination meter assembly.
- U0155Lost communication with combination meter assembly.
- U0155Lost communication with combination meter assembly.
- B2311Either condition is met: (a) Power window regulator motor assembly LH or RH (driver side) malfunctions (b)...
- B2312· The power window regulator master switch assembly is stuck. · The power window regulator master switch...
- B2313· Power window regulator motor assembly LH or RH (driver side) not initialized · Power window regulator motor...
- B1244· Malfunction in automatic light control sensor. · Open or short in automatic light control sensor circuit.
- B1244· Malfunction in automatic light control sensor. · Open or short in automatic light control sensor circuit.
- B2430LED Headlight LH Circuit Malfunction
- B2430LED Headlight LH Circuit Malfunction
- B2431LED Headlight RH Circuit Malfunction
- B2431LED Headlight RH Circuit Malfunction
- B2416· Malfunction in rear height control sensor sub-assembly · Open or short in rear height control sensor...
- B241A· Malfunction in rear height control sensor sub-assembly · Open or short in rear height control sensor...
- B2420Malfunction of headlight leveling ECU assembly
- B2450Initialization of the headlight leveling ECU assembly has not been performed
- B2451Vehicle specifications have not been stored
- B2452Vehicle condition not specified when initializing
- B2453The headlight leveling ECU assembly for another destination is installed on the vehicle
Common jobs · 1NZ-FE (17)
- Read / clear codes
- Engine oil & filter: replacement
- Valve clearance: adjustment
- Ignition coil: removal
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · installation
- Fuel pump: inspection · removal · disassembly · installation
- Injectors: removal
- Throttle body: inspection · removal
- Cylinder head gasket: removal
- Cylinder head: inspection · replacement · disassembly
- Engine assembly: inspection · removal · disassembly · installation
- Alternator: removal · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · 2NZ-FE (17)
- Read / clear codes
- Engine oil & filter: replacement
- Valve clearance: adjustment
- Ignition coil: removal
- Drive belt: on-vehicle inspection · removal · installation
- Coolant: replacement
- Water pump: on-vehicle inspection · removal · installation
- Thermostat: inspection · removal · installation
- Radiator: on-vehicle inspection · removal · installation
- Fuel pump: inspection · removal · disassembly · installation
- Injectors: removal
- Throttle body: inspection · removal
- Cylinder head gasket: installation
- Cylinder head: inspection · replacement · disassembly
- Engine assembly: inspection · removal · disassembly · installation
- Alternator: removal · installation
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · chassis & body (5)
- Clutch: inspection · removal · installation
- Front brakes: inspection · removal · disassembly · reassembly
- Rear brakes: inspection · removal · disassembly · reassembly
- Brake fluid: on-vehicle inspection
- Front drive shaft: inspection · removal · disassembly · reassembly
Repair Manual
General325 documents
Engine / Hybrid System986 documents
Drivetrain336 documents
Suspension52 documents
Brake367 documents
Steering94 documents
Audio / Visual / Telematics257 documents
Power Source / Network195 documents
Vehicle Interior1064 documents
Vehicle Exterior570 documents
New Car Features
General18 documents
Engine / Hybrid System108 documents
Drivetrain20 documents
Suspension11 documents
Brake17 documents
Steering10 documents
Audio / Visual / Telematics26 documents
Power Source / Network32 documents
Vehicle Interior80 documents
Vehicle Exterior47 documents