Home › Vehicle Exterior › BODY PANEL › FRONT SIDE MEMBER
BM19S0E _01 Vehicle Exterior _054879 BODY WELD POINT _0267228 FRONT SIDE MEMBER F

BODY WELD POINT  FRONT SIDE MEMBER  ASSEMBLY REPLACEMENT (PATTERN 1)  


K100644

With the radiator side support removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points


U135307E02
1.649,3.079 1.759,3.231 0.111,0.152 10 2 3.325,3.116 3.436,3.268 0.111,0.152 10 3 3.479,2.593 3.590,2.745 0.111,0.152 10 1 3.47,1.897 3.581,2.049 0.111,0.152 10 1 2.384,3.223 2.495,3.375 0.111,0.152 10 2 3.368,1.581 3.473,1.733 0.105,0.152 10 2 3.522,2.221 3.628,2.373 0.105,0.152 10 1 1.061,1.142 1.166,1.294 0.105,0.152 10 9 4.449,4.552 4.559,4.704 0.111,0.152 10 2 6.91,4.305 7.020,4.457 0.111,0.152 10 9 0.871,7.931 0.982,8.083 0.111,0.152 10 5 0.976,9.248 1.087,9.400 0.111,0.152 10 5 2.798,9.115 2.908,9.267 0.111,0.152 10 6 0.4,0.279 0.782,0.631 0.383,0.352 12 LH:

U135308E02
5.53,3.081 5.640,3.233 0.111,0.152 10 2 3.844,3.086 3.954,3.238 0.111,0.152 10 3 3.704,2.544 3.814,2.696 0.111,0.152 10 1 3.746,1.909 3.856,2.061 0.111,0.152 10 1 4.785,3.188 4.895,3.340 0.111,0.152 10 2 5.456,0.435 5.561,0.587 0.105,0.152 10 4 6.791,1.583 6.897,1.735 0.105,0.152 10 4 6.03,2.947 6.135,3.099 0.105,0.152 10 3 3.7,2.204 3.805,2.357 0.105,0.152 10 1 3.849,1.579 3.954,1.731 0.105,0.152 10 2 5.857,0.761 5.963,0.914 0.105,0.152 10 5 3.517,4.669 3.627,4.821 0.111,0.152 10 2 0.803,4.506 0.914,4.657 0.111,0.152 10 2 1.392,3.623 1.503,3.775 0.111,0.152 10 5 6.861,8.055 6.971,8.207 0.111,0.152 10 5 6.352,9.255 6.462,9.407 0.111,0.152 10 5 4.619,9.003 4.730,9.155 0.111,0.152 10 6 0.374,0.282 0.744,0.639 0.370,0.357 12 RH:

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld


INSTALLATION POINT
1.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

2.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

3.

Make sure to attach correctly in accordance with the body dimension diagram as this part affects the front wheel alignment.

4.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

5.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132080E01
3.583,2.667 3.167,2.667 3.167,2.667 2.781,2.208 false 0.833,9.417 0.333,9.417 0.333,9.417 0.74,8.198 false 0.365,0.25 0.948,0.656 0.583,0.406 12 false LH: 3.677,2.583 6.667,3.021 2.99,0.438 10 false FRONT SIDE MEMBER REINFORCEMENT 2.333,8.792 2.646,8.99 0.313,0.198 10 false *1 0.906,9.333 3.479,9.76 2.573,0.427 10 false FRONT SIDE MEMBER PLATE OUTER

K132081E02
3.75,2.333 4.083,2.333 4.083,2.333 4.427,1.885 false 6.083,9.417 6.667,9.417 6.667,9.417 6.208,8.313 false 0.365,0.25 1.021,0.708 0.656,0.458 12 false RH: 1.01,2.25 3.719,2.729 2.708,0.479 10 false FRONT SIDE MEMBER REINFORCEMENT 4.208,8.896 4.521,9.094 0.313,0.198 10 false *1 3.583,9.344 6.104,9.833 2.521,0.49 10 false FRONT SIDE MEMBER PLATE OUTER