Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR(for 3 Door)
BM19S0E _01 Vehicle Exterior _054879 BODY WELD POINT _0267232 CENTER BODY PILLAR(for 3 Door) F

BODY WELD POINT  CENTER BODY PILLAR(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K101564

With the quarter panel removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location


REMOVAL POINT
1.

*1 is reused.


U135356E04
1.396,0.813 1.271,0.375 1.271,0.375 1.083,0.375 false 0.354,9.51 0.885,9.677 0.531,0.167 10 false mm (in.) 2.438,0.438 3.208,0.615 0.771,0.177 10 false 20 (0.79) 0.479,1.25 1.25,1.427 0.771,0.177 10 false 305 (12.01) 2.094,1.438 2.865,1.615 0.771,0.177 10 false 275 (10.83) 0.896,0.313 1.094,0.542 0.198,0.229 10 false *1 0.969,1.604 1.083,1.76 0.115,0.156 10 false 2 2.375,1.813 2.49,1.969 0.115,0.156 10 false 3 5.635,0.375 5.75,0.531 0.115,0.156 10 false 6 4.813,1.344 4.927,1.5 0.115,0.156 10 false 1 1.104,5.365 1.875,5.542 0.771,0.177 10 false 215 (8.46) 5.24,4.771 5.354,4.927 0.115,0.156 10 false 2 3.865,4.771 3.979,4.927 0.115,0.156 10 false 2 2.042,7.031 2.813,7.208 0.771,0.177 10 false 25 (0.98) 0.667,8.365 0.771,8.521 0.104,0.156 10 false 5 2.344,8.438 3.115,8.615 0.771,0.177 10 false 150 (5.91)

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the center body pillar reinforcement and No.1 inner pillar with the standard number of welding points.

5.

After welding the center body pillar reinforcement and No.1 inner pillar to the vehicle side, install the *1.

6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132630E01
1.667,1.677 1.406,0.938 1.406,0.938 1.594,0.938 false 1.688,0.854 4.469,1.292 2.781,0.438 10 false CENTER BODY PILLAR REINFORCEMENT 3.344,2.208 4.667,2.833 1.323,0.625 10 false NO.1 INNER PILLAR 5.781,1.729 6.448,2.031 0.667,0.302 10 false 85 (3.35) 6.063,3.281 6.885,3.615 0.823,0.333 10 false 150 (5.91) 2.115,3.781 2.938,4.115 0.823,0.333 10 false 215 (8.46) 0.229,9.448 1.052,9.781 0.823,0.333 10 false mm (in.)

K132088E01
3.333,7.698 3.167,7.25 3.167,7.25 3,7.25 false 2.833,7.167 3.146,7.365 0.313,0.198 10 false *1