Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR(for 5 Door)
BM19S0E _01 Vehicle Exterior _054879 BODY WELD POINT _0267233 CENTER BODY PILLAR(for 5 Door) F

BODY WELD POINT  CENTER BODY PILLAR(for 5 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K100689

REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*1 is reused.


U158806E03
1.313,1 1.167,0.531 1.167,0.531 0.948,0.531 false 0.875,1.771 0.99,1.927 0.115,0.156 10 false 2 4.125,4.521 4.24,4.677 0.115,0.156 10 false 2 4.333,4.781 4.448,4.938 0.115,0.156 10 false 2 2.802,4.792 2.917,4.948 0.115,0.156 10 false 2 2.49,1.771 2.604,1.927 0.115,0.156 10 false 1 2.635,5.094 2.75,5.25 0.115,0.156 10 false 1 4.927,1.5 5.042,1.656 0.115,0.156 10 false 1 5.771,0.5 5.885,0.656 0.115,0.156 10 false 6 0.74,0.469 0.927,0.688 0.188,0.219 10 false *1 2.125,1.479 2.885,1.656 0.76,0.177 10 false 75 (2.95) 0.438,1.5 1.198,1.677 0.76,0.177 10 false 185 (7.28) 2.323,0.542 3.083,0.719 0.76,0.177 10 false 20 (0.79) 0.385,5.354 1.146,5.531 0.76,0.177 10 false 105 (4.13) 0.583,6.958 1.344,7.135 0.76,0.177 10 false 15 (0.59) 4.385,6.896 5.146,7.073 0.76,0.177 10 false 80 (3.15) 4.24,7.219 5,7.396 0.76,0.177 10 false 60 (2.36) 0.354,9.51 0.885,9.677 0.531,0.167 10 false mm (in.)

INSTALLATION


Symbol meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Carefully cut the center body pillar reinforcement so not to damage *1.

5.

Before temporarily installing the new parts, weld the center body pillar reinforcement and No.1 inner pillar with the standard number of welding points.

6.

After welding the center body pillar reinforcement and No.1 inner pillar to the vehicle side, install the rocker panel outer and *2.

7.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132089E02
1.646,1.583 1.417,0.75 1.417,0.75 1.75,0.75 false 2.875,2.656 3.208,2.656 false 5.083,2.167 5.417,2.167 5.417,2.167 5.688,2.583 false 1.802,0.667 4.667,1.167 2.865,0.5 10 false CENTER BODY PILLAR REINFORCEMENT 4.698,1.552 5.417,1.917 0.719,0.365 10 false 15 (0.59) 0.198,3.458 1,3.833 0.802,0.375 10 false 40 (1.57) 3.26,2.573 3.573,2.771 0.313,0.198 10 false *1 3.729,2.094 5.083,2.625 1.354,0.531 10 false NO.1 INNER PILLAR 4.708,3.688 5.833,4.167 1.125,0.479 10 false 380 (14.96) 0.323,9.354 1.5,9.833 1.177,0.479 10 false mm (in.)

K132090E02
3.073,4.719 3.823,4.719 false 3.333,8.083 3.167,7.667 3.167,7.667 2.917,7.667 false 1.417,4.625 3.125,5.073 1.708,0.448 10 false ROCKER PANEL OUTER 2.75,7.583 3.063,7.781 0.313,0.198 10 false *2