Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL(for 5 Door) › 2011.08–2018.06
BM19S0E _01 Vehicle Exterior _054879 BODY WELD POINT _0267244 ROCKER PANEL(for 5 Door) F

BODY WELD POINT  ROCKER PANEL(for 5 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K100691

Weld work for 980 MPa ultra high strength steel

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*1: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 14 Cyc. (0.23 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*2: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

Carefully cut the center body pillar reinforcement so not to damage *3.

3.

Reuse *4, as the area of the outer panel that is cut and joined is in front of the supplied part cut position.

4.

Reuse *5, as the area of the outer panel that is cut and joined is to the rear of the supplied part cut position.


U135373E04
5.49,1.531 5.302,1.396 5.302,1.396 5.125,1.396 false 5.729,1.594 6.229,0.49 6.229,0.49 5.99,0.49 false 4.219,2.417 4.333,2.573 0.115,0.156 10 false 2 4.323,4.146 4.438,4.302 0.115,0.156 10 false 2 3.823,4.146 3.938,4.302 0.115,0.156 10 false 1 3.302,4.146 3.417,4.302 0.115,0.156 10 false 1 2.365,3.25 2.479,3.406 0.115,0.156 10 false 1 4.406,2.927 4.521,3.083 0.115,0.156 10 false 1 4.24,3.156 4.354,3.313 0.115,0.156 10 false 3 2.365,3 2.479,3.156 0.115,0.156 10 false 3 2.688,4.146 2.885,4.302 0.198,0.156 10 false 14 1.635,3.063 1.833,3.219 0.198,0.156 10 false 10 4.969,1.333 5.135,1.479 0.167,0.146 10 false *3 2.25,6.344 3.01,6.521 0.76,0.177 10 false 100 (3.94) 2.365,6.74 3.125,6.917 0.76,0.177 10 false 55 (2.17) 2.198,2.615 2.958,2.792 0.76,0.177 10 false 90 (3.54) 0.354,9.51 0.885,9.677 0.531,0.167 10 false mm (in.) 0.396,0.25 0.781,0.604 0.385,0.354 12 false LH: 3.146,0.417 6.01,0.823 2.865,0.406 10 false CENTER BODY PILLAR REINFORCEMENT

U135374E03
1.933,1.165 2.044,1.317 0.111,0.152 10 3 1.938,2.44 2.048,2.592 0.111,0.152 10 5 1.644,4.154 1.754,4.306 0.111,0.152 10 3 1.447,5.48 1.558,5.632 0.111,0.152 10 3 6.342,0.371 6.452,0.523 0.111,0.152 10 4 6.188,3.355 6.298,3.507 0.111,0.152 10 2 5.585,4.163 5.696,4.315 0.111,0.152 10 4 5.45,5.476 5.560,5.627 0.111,0.152 10 3 5.763,0.382 5.869,0.534 0.105,0.152 10 1 4.535,2.469 4.640,2.621 0.105,0.152 10 2 3.895,9.423 4.001,9.575 0.105,0.152 10 2 0.677,5.358 0.840,5.505 0.163,0.147 10 *5 2.433,2.407 2.596,2.553 0.163,0.147 10 *4 0.932,2.492 1.695,2.669 0.764,0.177 10 140 (5.51) 5.102,3.412 5.866,3.589 0.764,0.177 10 195 (7.68) 5.649,5.462 6.412,5.639 0.764,0.177 10 65 (2.56) 1.665,5.462 2.429,5.639 0.764,0.177 10 20 (0.79) 0.356,9.506 0.889,9.671 0.533,0.165 10 mm (in.) 0.4,0.25 0.782,0.602 0.383,0.352 12 LH: 1.353,4.996 1.069,5.417 1.069,5.417 0.854,5.417 false 2.041,2.144 2.189,2.47 2.189,2.47 2.395,2.47 false

U135375E04
1.802,1.406 2,1.271 2,1.271 2.167,1.271 false 1.542,1.49 1.042,0.385 1.042,0.385 1.281,0.385 false 5.25,2.927 5.365,3.083 0.115,0.156 10 false 2 3.365,2.323 3.479,2.479 0.115,0.156 10 false 2 5.76,2.927 5.875,3.083 0.115,0.156 10 false 8 5.094,2.698 5.208,2.854 0.115,0.156 10 false 1 3.083,2.833 3.198,2.99 0.115,0.156 10 false 1 4.125,4.052 4.24,4.208 0.115,0.156 10 false 1 3.625,4.052 3.74,4.208 0.115,0.156 10 false 1 3.083,4.052 3.198,4.208 0.115,0.156 10 false 2 4.885,2.469 5,2.625 0.115,0.156 10 false 3 3.177,3.094 3.292,3.25 0.115,0.156 10 false 3 4.771,4.042 4.969,4.198 0.198,0.156 10 false 14 2.188,1.198 2.354,1.344 0.167,0.146 10 false *3 4.406,6.344 5.167,6.521 0.76,0.177 10 false 100 (3.94) 4.375,6.708 5.135,6.885 0.76,0.177 10 false 55 (2.17) 0.354,9.51 0.885,9.677 0.531,0.167 10 false mm (in.) 1.354,0.281 4.219,0.688 2.865,0.406 10 false CENTER BODY PILLAR REINFORCEMENT 0.375,0.25 0.75,0.604 0.375,0.354 12 false RH:

U135376E02
1.377,1.191 1.488,1.342 0.111,0.152 10 3 1.377,2.475 1.488,2.627 0.111,0.152 10 5 5.261,3.374 5.371,3.526 0.111,0.152 10 2 5.064,0.39 5.175,0.542 0.111,0.152 10 4 5.865,4.166 5.976,4.317 0.111,0.152 10 4 6.127,5.548 6.238,5.700 0.111,0.152 10 3 1.83,5.553 1.941,5.704 0.111,0.152 10 3 1.503,4.184 1.614,4.336 0.111,0.152 10 3 5.644,0.386 5.750,0.539 0.105,0.152 10 1 6.914,2.497 7.020,2.649 0.105,0.152 10 2 3.585,9.456 3.690,9.608 0.105,0.152 10 2 0.57,2.433 0.733,2.580 0.163,0.147 10 *4 2.181,5.376 2.344,5.522 0.163,0.147 10 *5 0.374,0.253 0.744,0.609 0.370,0.357 12 RH: 1.639,2.513 2.403,2.690 0.764,0.177 10 140 (5.51) 5.502,3.428 6.265,3.605 0.764,0.177 10 195 (7.68) 5.137,5.492 5.901,5.669 0.764,0.177 10 65 (2.56) 0.831,5.502 1.595,5.678 0.764,0.177 10 20 (0.79) 0.356,9.506 0.889,9.671 0.533,0.165 10 mm (in.) 1.64,5.024 1.924,5.444 1.924,5.444 2.139,5.444 false 1.111,2.172 0.963,2.498 0.963,2.498 0.757,2.498 false

INSTALLATION


Symbol meaning
K108820

Remove Weld Points
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Carefully cut the rocker reinforce outer so not to damage *3.

5.

Follow the welding conditions when welding *1 and *2 to assure sufficient weld strength. (See the introduction)

6.

Before temporarily installing the new parts, weld the rocker reinforce outer, center body pillar reinforcement and No.1 inner pillar with the standard number of welding points.

7.

After welding the rocker reinforce outer, center body pillar reinforcement and No.1 inner pillar to the vehicle side, install the rocker panel outer, *4 and *5.

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


U135377E04
3.833,2.823 4.219,1.667 4.219,1.667 4.552,1.667 false 3,2.854 3.208,2.438 3.208,2.438 3.365,2.438 false 3.052,2.927 3.208,2.438 false 1.323,8.604 1.125,9.208 1.125,9.208 1.563,9.208 false 5.385,8.729 5.219,9.156 5.219,9.156 5.542,9.156 false 1.969,0.802 2.073,0.958 0.104,0.156 10 false 1 4.156,3.74 4.26,3.896 0.104,0.156 10 false 2 3.406,2.365 3.573,2.51 0.167,0.146 10 false *3 4.26,8.375 5.021,8.552 0.76,0.177 10 false 255 (10.04) 2.427,3.479 3.188,3.656 0.76,0.177 10 false 195 (7.68) 5.354,3.479 6.115,3.656 0.76,0.177 10 false 65 (2.56) 0.344,8 1.104,8.177 0.76,0.177 10 false 40 (1.57) 0.354,9.51 0.885,9.677 0.531,0.167 10 false mm (in.) 0.396,0.25 0.781,0.604 0.385,0.354 12 false LH: 4.594,1.573 6.698,1.948 2.104,0.375 10 false ROCKER REINFORCE OUTER 1.604,9.135 4.469,9.542 2.865,0.406 10 false CENTER BODY PILLAR REINFORCEMENT 5.594,9.094 7,9.5 1.406,0.406 10 false NO.1 INNER PILLAR

K132100E02
1.24,1.698 1.854,2.052 0.615,0.354 10 false 10 (0.39) 2.667,1.688 3.281,2.042 0.615,0.354 10 false 10 (0.39) 1.396,3.115 2.01,3.469 0.615,0.354 10 false 15 (0.59) 2.094,3.125 2.708,3.479 0.615,0.354 10 false 15 (0.59) 2.917,7.021 3.229,7.219 0.313,0.198 10 false *1 5.219,7.083 5.531,7.281 0.313,0.198 10 false *1 6.073,7 6.385,7.198 0.313,0.198 10 false *1 2.74,8.344 3.052,8.542 0.313,0.198 10 false *1 4.104,8.344 4.417,8.542 0.313,0.198 10 false *1 6.146,8.344 6.458,8.542 0.313,0.198 10 false *1 0.354,9.417 1.5,9.792 1.146,0.375 10 false mm (in.) 0.344,0.271 0.938,0.729 0.594,0.458 12 false LH:

K132101E01
0.375,0.271 0.917,0.667 0.542,0.396 12 false LH: 3.167,2.76 3.479,2.958 0.313,0.198 10 false *1 3.677,2.792 3.99,2.99 0.313,0.198 10 false *1 5.271,2.781 5.583,2.979 0.313,0.198 10 false *1 5.646,2.354 5.958,2.552 0.313,0.198 10 false *1 5.542,4.427 5.854,4.625 0.313,0.198 10 false *1 5.26,4.021 5.573,4.219 0.313,0.198 10 false *1 4.781,4.021 5.094,4.219 0.313,0.198 10 false *1 3.99,4 4.302,4.198 0.313,0.198 10 false *1 3.365,9.385 4.198,9.844 0.833,0.458 10 false 10 (0.39) 4.625,9.396 5.458,9.854 0.833,0.458 10 false 10 (0.39) 0.344,9.365 1.167,9.833 0.823,0.469 10 false mm (in.)

K132102E01
3.833,5.75 4.167,5.75 4.167,5.75 4.583,3.667 false 2,8.167 2.417,8.5 2.417,8.5 2.75,8.5 false 5.667,8.25 6.167,8.667 6.167,8.667 6.333,8.667 false 0.354,0.333 0.917,0.833 0.563,0.5 12 false LH: 3.313,1.875 3.625,2.073 0.313,0.198 10 false *2 5.115,1.938 5.427,2.135 0.313,0.198 10 false *2 5.396,2.563 5.708,2.76 0.313,0.198 10 false *2 3.135,2.188 3.448,2.385 0.313,0.198 10 false *2 2.979,2.792 3.292,2.99 0.313,0.198 10 false *2 3.781,3.844 4.094,4.042 0.313,0.198 10 false *2 1.885,7.146 2.198,7.344 0.313,0.198 10 false *2 5.031,7.208 5.344,7.406 0.313,0.198 10 false *2 1.615,8.865 1.927,9.063 0.313,0.198 10 false *2 5.063,8.865 5.375,9.063 0.313,0.198 10 false *2 2.208,5.667 3.938,6.115 1.729,0.448 10 false ROCKER PANEL OUTER 2.813,8.417 3.125,8.615 0.313,0.198 10 false *4 6.417,8.583 6.729,8.781 0.313,0.198 10 false *5

U135381E04
3.417,2.854 3.063,1.771 3.063,1.771 2.781,1.771 false 1.323,8.635 1.125,9.198 1.125,9.198 1.552,9.198 false 5.365,8.76 5.198,9.198 5.198,9.198 5.51,9.198 false 4.25,2.938 4.042,2.521 4.042,2.521 3.885,2.521 false 4.198,3.021 4.042,2.521 false 5.438,0.823 5.542,0.979 0.104,0.156 10 false 1 3.25,3.771 3.354,3.927 0.104,0.156 10 false 2 3.698,2.458 3.865,2.604 0.167,0.146 10 false *3 4.198,3.5 4.958,3.677 0.76,0.177 10 false 195 (7.68) 1.354,3.5 2.115,3.677 0.76,0.177 10 false 65 (2.56) 2.104,8.042 2.865,8.219 0.76,0.177 10 false 40 (1.57) 6.208,8.406 6.969,8.583 0.76,0.177 10 false 255 (10.04) 0.375,0.25 0.75,0.604 0.375,0.354 12 false RH: 0.729,1.677 2.75,2.094 2.021,0.417 10 false ROCKER REINFORCE OUTER 1.615,9.135 4.479,9.542 2.865,0.406 10 false CENTER BODY PILLAR REINFORCEMENT 5.583,9.135 6.99,9.542 1.406,0.406 10 false NO.1 INNER PILLAR 0.354,9.51 0.885,9.677 0.531,0.167 10 false mm (in.)

K132103E01
0.365,0.417 0.917,0.656 0.552,0.24 12 false RH: 2.052,1.688 3.427,1.885 1.375,0.198 10 false 10 (0.39) 3.5,1.698 4.875,1.896 1.375,0.198 10 false 10 (0.39) 2.458,3.115 3.833,3.313 1.375,0.198 10 false 15 (0.59) 3.135,3.125 4.51,3.323 1.375,0.198 10 false 15 (0.59) 2.875,6.979 3.188,7.177 0.313,0.198 10 false *1 3.792,7.063 4.104,7.26 0.313,0.198 10 false *1 6.063,7.031 6.375,7.229 0.313,0.198 10 false *1 6.271,8.344 6.583,8.542 0.313,0.198 10 false *1 4.75,8.344 5.063,8.542 0.313,0.198 10 false *1 2.833,8.344 3.146,8.542 0.313,0.198 10 false *1 0.333,9.417 1.167,9.875 0.833,0.458 10 false mm (in.)

K132104E01
0.25,0.26 0.885,0.75 0.635,0.49 12 false RH: 1.26,2.115 1.573,2.313 0.313,0.198 10 false *1 1.677,2.604 1.99,2.802 0.313,0.198 10 false *1 3.594,2.219 3.906,2.417 0.313,0.198 10 false *1 3.125,2.583 3.438,2.781 0.313,0.198 10 false *1 3.823,2.604 4.135,2.802 0.313,0.198 10 false *1 1.375,4.188 1.688,4.385 0.313,0.198 10 false *1 1.677,3.865 1.99,4.063 0.313,0.198 10 false *1 2.281,3.823 2.594,4.021 0.313,0.198 10 false *1 2.938,3.875 3.25,4.073 0.313,0.198 10 false *1 0.323,9.417 1.25,9.875 0.927,0.458 10 false mm (in.) 2.615,9.469 3.531,9.844 0.917,0.375 10 false 10 (0.39) 3.865,9.479 4.781,9.854 0.917,0.375 10 false 10 (0.39)

K132105E01
2.604,3.656 3,5.75 3,5.75 3.25,5.75 false 0.833,8.667 1,8.667 1,8.667 1.646,8.198 false 4.5,8.5 4.75,8.5 4.75,8.5 5.188,8.167 false 0.417,0.323 0.969,0.75 0.552,0.427 12 false RH: 1.604,1.885 1.917,2.083 0.313,0.198 10 false *2 3.521,2.167 3.833,2.365 0.313,0.198 10 false *2 3.802,2.792 4.115,2.99 0.313,0.198 10 false *2 1.458,2.542 1.771,2.74 0.313,0.198 10 false *2 2.969,3.885 3.281,4.083 0.313,0.198 10 false *2 3.354,5.667 5.167,6.198 1.813,0.531 10 false ROCKER PANEL OUTER 1.854,7.219 2.167,7.417 0.313,0.198 10 false *2 4.917,7.167 5.229,7.365 0.313,0.198 10 false *2 1.885,8.813 2.198,9.01 0.313,0.198 10 false *2 5.177,8.885 5.49,9.083 0.313,0.198 10 false *2 0.656,8.583 0.969,8.781 0.313,0.198 10 false *5 4.323,8.417 4.635,8.615 0.313,0.198 10 false *4