Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL(for 3 Door)
BM19S0E _01 Vehicle Exterior _054879 BODY WELD POINT _0267245 QUARTER PANEL(for 3 Door) F

BODY WELD POINT  QUARTER PANEL(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K101569

Quarter Panel Replacement Using Adhesive


Work Procedure
1.

Cut the wheel arch portion.

2.

Heat the quarter panel adhesive area and remove the quarter panel.

HINT:

Using an industrial heater gun or gas burner, heat the quarter panel to 110 to 140°C. Make sure the quarter panel does not warp.


3.

Clean off any adhesive that remains on the vehicle.

HINT:
·

Using an industrial heater gun or gas burner, heat the adhesive to 110 to 140°C.

·

Using a scraper, scrape away the adhesive.

·

If adhesive remains, the strength of any subsequently applied adhesive will be weak.



4.

Using a disc grinder or belt sander, scuff and sand any adhesive that remains on the vehicle.

HINT:

Scuff at a width of approximately 10 mm (0.39 in.) over the previous adhesive coating.


5.

Apply adhesive to the exposed metal areas on the vehicle. Using a spatula, spread the adhesive evenly.

6.

Apply adhesive to the vehicle again.

7.

Using #60-120 grit sandpaper, scuff the adhesive application area on the new quarter panel.

8.

Apply adhesive to the new quarter panel. Using a spatula, spread the adhesive evenly.

9.

Using a vise grip or the palms of your hands, press the quarter panel so that the thickness of the adhesive is even.

10.

Complete installation the new quarter panel.

11.

Dry the adhesive areas of the new quarter panel.

HINT:
·

With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

·

Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)




REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*1 in illustration above indicates where the adhesive is located.

2.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.



U135387E04
5.865,7.729 5.417,7.729 false 4.729,4.948 5.604,4.333 5.604,4.333 5.75,4.333 false 5.24,7.667 5.406,7.813 0.167,0.146 10 false *1 5.594,8.438 5.896,8.594 0.302,0.156 10 false a - a 3.938,2.792 4.708,2.969 0.771,0.177 10 false 220 (8.66) 1.677,3.479 2.448,3.656 0.771,0.177 10 false 20 (0.79) 3.521,3.469 3.635,3.625 0.115,0.156 10 false 5 3.302,3.76 3.417,3.917 0.115,0.156 10 false 4 5.792,3.969 5.906,4.125 0.115,0.156 10 false 1 5.5,3.594 5.615,3.75 0.115,0.156 10 false 2 3.823,3.656 3.938,3.813 0.115,0.156 10 false 2 1.708,4.51 1.906,4.667 0.198,0.156 10 false 19 3.021,6.281 3.219,6.438 0.198,0.156 10 false 21 5.802,4.25 6.042,4.458 0.24,0.208 10 false *1 4.208,4.594 4.302,4.75 0.094,0.156 10 false a 4.208,5.156 4.302,5.313 0.094,0.156 10 false a 0.354,9.51 0.99,9.792 0.635,0.281 10 false mm (in.)

K132107

INSTALLATION


Symbol meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

When welding *1, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

4.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



5.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the area indicated by *2 in the illustration.

HINT:

Apply enough adhesive for the panels to stick to each other.


6.

Areas indicated by *3 in the illustration, combine welding with adhesive. (difficult to get stable strength by one way) If use the spot welder, modify the spot tip as shown in the illustration *4 so that it can fit in the narrow flange.

7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132108E02
5.833,1.5 6.271,1.5 false 3.833,2.583 4.833,2 4.833,2 5,2 false 2.521,3.646 2.75,4.417 2.75,4.417 2.917,4.417 false 5.917,5 6.167,4.75 6.167,4.75 6.417,4.75 false 3.104,7.521 3.354,7.521 3.354,7.521 3.688,7.854 false 4.25,9.333 4.844,8.104 false 4.5,9.333 4.25,9.333 4.25,9.333 4.833,8.354 false 5.083,1.917 5.396,2.115 0.313,0.198 10 false *2 5.646,1.417 5.958,1.615 0.313,0.198 10 false *2 3.771,3.615 4.083,3.813 0.313,0.198 10 false *3 2.99,4.333 4.333,4.781 1.344,0.448 10 false QUARTER PANEL 2.219,5.865 3.448,6.063 1.229,0.198 10 false 5 (0.20) 5.052,5.167 6.281,5.365 1.229,0.198 10 false 3 (0.12) 6.5,4.667 7.156,5.083 0.656,0.417 10 false Spot Tip 5.688,5.469 6,5.667 0.313,0.198 10 false *4 1.271,7.438 3.052,7.948 1.781,0.51 10 false FUEL FILLER OPENING LID 4.563,9.25 6.188,9.688 1.625,0.438 10 false WATERPROOF RIVETS 0.354,9.365 1.417,9.875 1.063,0.51 10 false mm (in.)

K132109E01
6.323,7.74 6.635,7.938 0.313,0.198 10 false *1 6.042,8.885 6.354,9.083 0.313,0.198 10 false *1