INSPECT HOOD SUB-ASSEMBLY
Check that the clearance measurements are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 2.0 to 6.0 mm
(0.0787 to 0.236 in.) |
D | 2.3 to 5.3 mm
(0.0905 to 0.208 in.) |
| B | 11.0 mm
(0.433 in.) |
E | 1.2 to 5.2 mm
(0.0472 to 0.204 in.) |
| C | 5.0 mm
(0.196 in.) |
- | - |
Centering bolts are used to mount the hood hinge and the hood lock. The hood and the hood lock cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.
ADJUST HOOD SUB-ASSEMBLY
Loosen the 4 hood side hinge bolts.
Move the hood to adjust the clearance to within the standard range.
Tighten the 4 hood side hinge bolts after the adjustment.
Adjust the height of the hood front end by turning the 2 center hood cushions.
The center hood cushion can be raised and lowered by turning it.
Adjust the hood lock.
Loosen the 3 bolts.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
INSPECT FRONT DOOR
Check that the clearance measurements are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 3.0 to 6.0 mm
(0.118 to 0.232 in.) |
F | 3.0 mm
(0.118 in.) |
| B | 2.1 to 5.1 mm
(0.0826 to 0.200 in.) |
G | 3.6 to 6.6 mm
(0.141 to 0.259 in.) |
| C | 3.5 to 6.5 mm
(0.137 to 0.255 in.) |
H | -1.5 to 1.5 mm
(-0.0590 to 0.0590 in.) |
| D | 2.9 mm
(0.114 in.) |
I | 5.5 to 8.5 mm
(0.216 to 0.334 in.) |
| E | 3.5 to 6.5 mm
(0.137 to 0.255 in.) |
J | 5.5 to 8.5 mm
(0.216 to 0.334 in.) |
Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.
ADJUST FRONT DOOR
Make sure that the ignition switch is always OFF during adjusting door lock strikers.
Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.
Tighten the body side hinge bolts after the adjustment.
Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.
Tighten the door side hinge bolts after the adjustment.
Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.
Using a "TORX" socket wrench T40, tighten the striker mounting screws after the adjustment.
INSPECT REAR DOOR
Check that the clearance measurements are within the standard ranges.
| Area | Specified Condition | Area | Specified Condition |
|---|---|---|---|
| A | 3.6 to 6.6 mm
(0.141 to 0.259 in.) |
D | 1.2 to 4.2 mm
(0.0472 to 0.165 in.) |
| B | -1.5 to 1.5 mm
(-0.0590 to 0.0590 in.) |
E | 2.8 to 5.8 mm
(0.110 to 0.228 in.) |
| C | 3.5 to 6.5 mm
(0.137 to 0.255 in.) |
F | 5.5 to 8.5 mm
(0.216 to 0.334 in.) |
Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.
ADJUST REAR DOOR
Make sure that the ignition switch is always LOCK during adjusting door lock strikers.
Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.
Tighten the body side hinge bolts after the adjustment.
Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.
Tighten the door side hinge bolts after the adjustment.
Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.
INSPECT BACK DOOR
Check that the clearance measurements of areas "A" to "L" are within the standard ranges.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 6.0 to 9.0 mm (0.236 to 0.354 in.) | B | -0.5 to 2.5 mm (-0.020 to 0.098 in.) |
| C | 6.0 to 9.0 mm (0.236 to 0.354 in.) | D | -0.5 to 2.5 mm (-0.020 to 0.098 in.) |
| E | 6.0 to 9.0 mm (0.236 to 0.354 in.) | F | -0.2 to 2.8 mm (-0.008 to 0.110 in.) |
| G | 3.0 to 8.0 mm (0.118 to 0.315 in.) | H | 5.0 to 9.0 mm (0.197 to 0.354 in.) |
| I | 4.0 to 9.0 mm (0.157 to 0.354 in.) | J | 4.4 to 8.4 mm (0.173 to 0.331 in.) |
| K | 3.8 to 7.8 mm (0.150 to 0.307 in.) | L | 3.8 to 7.8 mm (0.150 to 0.307 in.) |
Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.
ADJUST BACK DOOR
Adjust the door position.
Horizontally and vertically adjust the door by loosening the door side hinge bolts.
Adjust the striker position.
Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a plastic hammer.
Using a "TORX" socket wrench T40, tighten the striker mounting bolts after the adjustment.