Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2014.07–2016.09
NM19S0E _51 Engine / Hybrid System _051391 2NZ-FE ENGINE CONTROL _0247856 SFI SYSTEM UN GENERAL/CONTROL/DETAILS F

2NZ-FE ENGINE CONTROL  SFI SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the 2NZ-FE engine control system are as follows.

Components Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA and ETCS-i to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Crank Position Sensor (Rotor Teeth) Pickup Coil Type (36 - 2) 1 This sensor detects the engine speed and performs cylinder identification.
Cam Position Sensor (Rotor Teeth) Pickup Coil Type (3) 1 This sensor performs cylinder identification.
Knock Control Sensor Built-in Piezoelectric Element Type (Flat Type) 1 This sensor detects an occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor uses a built-in hot-wire to directly detect the intake air mass.
Throttle Position Sensor Non-contact Type 1 This sensor detects the throttle valve opening angle.
Oxygen Sensor Cup Type with Heater 2 This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Accelerator Pedal Sensor Assembly Non-contact Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Fuel Injector Assembly 12-hole Type 4 The fuel injector assembly is an electromagnetically-operated solenoid with a nozzle which injects fuel in accordance with signals from the ECM.
E.F.I. Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the water temperature by means of an internal thermistor.



SYSTEM CONTROL


a.

The engine control system of the 2NZ-FE engine has the following systems.

Components Function
Sequential multiport Fuel Injection (SFI) An L-type SFI system is used, the intake air mass is detected with a hot-wire type intake mass air flow meter sub-assembly. The fuel injection system is a sequential multiport fuel injection system.
Electronic Spark Advance (ESA) The ECM determines the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signal to the igniter. The ECM corrects ignition timing in response to engine knocking.
Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort, the throttle valve opening control request from the ECM, and the condition of the engine and the vehicle.
Variable Valve Timing-intelligent (VVT-i) Regulates operation of the intake camshaft to ensure optimal valve timing in accordance with engine operating conditions.
Fuel Pump Control Fuel pump operation is controlled by signals from the ECM. The fuel pump is stopped when the SRS airbags deploy.
Cooling Fan Control Cooling fan operation is controlled by signals from the ECM based on the E.F.I. engine coolant temperature sensor signal.
Heated Oxygen Sensor Heater Control Maintains the temperature of the oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration.
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Air Conditioning Cut-off Control By turning the air conditioning compressor on or off in accordance with engine operating conditions, drivability is maintained.
Brake Override System Restricts the driving torque when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual)


b.

Variable Valve Timing-intelligent (VVT-i) System

i.

The VVT-i system is designed to control the intake camshafts within a range of 40° (of crankshaft angle) to provide valve timing that is optimally suited to engine operating conditions. This improves torque in all speed ranges as well as increasing fuel economy and reducing exhaust emissions.

W104586E09
2.031,2.042 1.354,0.417 1.354,0.417 1.167,0.417 true 3.438,1.49 3.813,0.333 3.813,0.333 3.969,0.333 true 3.26,1.833 3.948,2.896 3.948,2.896 4.094,2.896 true 1.094,3.042 0.51,3.833 0.51,3.833 0.51,4.042 true 0.073,0.292 1.146,1.323 1.073,1.031 10 false Camshaft Timing Oil Control Valve Assembly 4.031,0.219 5.406,0.573 1.375,0.354 10 false Cam Position Sensor 5.51,1.552 5.906,1.792 0.396,0.24 10 false ECM 5.688,2.354 7.042,3.302 1.354,0.948 10 false Intake Mass Air Flow Meter Sub-assembly 5.354,4.26 6.948,4.719 1.594,0.458 10 false Throttle Position Sensor 4.188,2.813 5.063,4.031 0.875,1.219 10 false E.F.I. Engine Coolant Temperature Sensor 0.083,4.104 1.552,4.646 1.469,0.542 10 false Crank Position Sensor

W105016E05
3.167,0.24 3.375,0.24 3.375,0.24 3.802,0.635 true 3.729,2.781 3.229,3.458 3.229,3.458 3.385,3.458 true 4.302,0.438 4.563,0.208 4.563,0.208 4.646,0.208 true 4.375,0.698 4.615,0.542 4.615,0.542 4.708,0.542 true 1.698,0.135 3.448,0.406 1.75,0.271 10 false VVT-i Operation Range 4.104,0.167 4.521,0.375 0.417,0.208 10 false TDC 4.708,0.146 5.01,0.354 0.302,0.208 10 false 2° 4.729,0.479 5.031,0.688 0.302,0.208 10 false 7° 3.333,0.51 3.76,0.76 0.427,0.25 10 false 33° 3,2.542 3.427,2.792 0.427,0.25 10 false 52° 3.865,3.021 4.292,3.271 0.427,0.25 10 false 12° 5.115,2.656 5.542,2.906 0.427,0.25 10 false 34° 4.125,3.104 4.698,3.375 0.573,0.271 10 false BDC 0.51,2.979 2.344,3.198 1.833,0.219 10 false : Intake Valve Opening Angle 0.51,3.302 2.594,3.573 2.083,0.271 10 false : Exhaust Valve Opening Angle 3.438,3.365 5.063,3.583 1.625,0.219 10 false VVT-i Operation Range


ii.

The VVT-i system delivers excellent driving performance appropriate to the driving situations described below.

Operation State Objective Effect
·

During Idling

·

At Light Load


W132548E01
2.063,0.313 3.25,0.594 1.188,0.281 10 false Latest Timing 1.594,0.26 1.99,0.51 0.396,0.25 10 false TDC 0.927,1 1.198,1.313 0.271,0.313 10 false EX 2.427,1.01 2.802,1.24 0.375,0.229 10 false IN 1.604,1.771 2.281,2.042 0.677,0.271 10 false BDC

Eliminating overlap to reduce blow back to the intake side.
·

Stabilized idling rpm

·

Better fuel economy


At Medium Load
W132549E01
0.896,1.052 1.146,1.281 0.25,0.229 10 false EX 2.365,1.042 2.677,1.24 0.313,0.198 10 false IN 1.875,0.198 3.115,0.5 1.24,0.302 10 false to Advance Side

Increasing overlap to increase internal EGR to reduce pumping loss.
·

Better fuel economy

·

Improved emission control


In Low to Medium Speed Range with Heavy Load
W132549E01
0.896,1.052 1.146,1.281 0.25,0.229 10 false EX 2.365,1.042 2.677,1.24 0.313,0.198 10 false IN 1.875,0.198 3.115,0.5 1.24,0.302 10 false to Advance Side

Advancing the intake valve close timing for volumetric efficiency improvement. Improved torque in low to medium speed range
In High Speed Range with Heavy Load
W132550E01
0.906,0.99 1.156,1.24 0.25,0.25 10 false EX 2.375,0.99 2.688,1.188 0.313,0.198 10 false IN 0.438,1.5 1.344,2.031 0.906,0.531 10 false to Retard Side

Retarding the intake valve close timing for volumetric efficiency improvement. Improved output
At Low Temperatures
W132551E01
2.417,1.063 2.729,1.26 0.313,0.198 10 false IN 0.938,1.073 1.177,1.313 0.24,0.24 10 false EX 2.052,0.302 3.177,0.583 1.125,0.281 10 false Latest Timing

Eliminating overlap to prevent blow back to the intake side from leading to the lean burning condition, and stabilize the idling speed at fast idle.
·

Stabilized fast idle rpm

·

Better fuel economy


·

Upon Starting the Engine

·

Upon Stopping the Engine


W132551E01
2.417,1.063 2.729,1.26 0.313,0.198 10 false IN 0.938,1.073 1.177,1.313 0.24,0.24 10 false EX 2.052,0.302 3.177,0.583 1.125,0.281 10 false Latest Timing

Eliminating overlap to reduce blow back to the intake side. Improved startability



c.

Fuel Pump Control

i.

In this system, the airbag deployment signal from the airbag sensor assembly is detected by the ECM, and it turns off the circuit opening relay. After the fuel cut control has been activated, turning the ignition switch from off to ON cancels the fuel cut control and the engine can be restarted.



d.

Cooling Fan Control

i.

A cooling fan control system controlled to achieve an optimal fan speed in accordance with the E.F.I. engine coolant temperature and air conditioning operating conditions.




CONSTRUCTION


a.

ECM

i.

The ECM is installed in the engine compartment. As a result, the wiring harness has been shortened, thus realizing weight reduction.

W123382E03
3.729,1.385 4.719,0.385 4.719,0.385 4.958,0.385 true 5.01,0.26 5.292,0.531 0.281,0.271 10 false *1

Text in Illustration
*1 ECM - -



b.

Crank Position and Cam Position Sensors

i.

Pick-up coil type sensors are used for the crank position, intake cam position sensor.


ii.

The timing sprocket of the crankshaft has 34 teeth, with 2 teeth missing. When the crankshaft rotates, the crank position sensor generates pulse signals, which fluctuates between high and low, whenever each tooth of the timing sprocket passes the sensor. In one crankshaft rotation, a pulse signal fluctuates 33 times, 1 for every 10° of crankshaft rotation, and fluctuates once for the 30° of crankshaft rotation (2 missing teeth location). The crank position sensor transmits those pulse signals as crank position signals (NE signals) to the ECM. The ECM uses the signals for detecting the crank position as well as engine speed. Also, the ECM determines the top dead center position of the crankshaft through the signal fluctuation at the 30° of crankshaft rotation (2 missing teeth location).


iii.

To detect the cam position, a timing rotor on the intake camshaft is used to generate 3 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft.

W103894E08
0.917,3.313 1.354,3.948 1.354,3.948 1.531,3.948 true 2.156,2.667 2.719,3.948 2.719,3.948 2.948,3.948 true 5.76,2.854 6.323,4.146 6.323,4.146 6.552,4.146 true 5.198,1.792 4.635,0.51 4.635,0.51 4.406,0.51 true 1.542,3.875 1.698,4.052 0.156,0.177 10 false *1 2.948,3.875 3.104,4.052 0.156,0.177 10 false *2 6.552,4.063 6.708,4.24 0.156,0.177 10 false *3 4.208,0.406 4.365,0.583 0.156,0.177 10 false *4

Text in Illustration
*1 Crank Position Sensor *2 Timing Sprocket
*3 Exhaust Cam Position Sensor *4 Timing Rotor

W105014E12
0.177,0.281 2.26,0.781 2.083,0.5 12 false Sensor Output Waveforms: 0.031,1.948 0.969,2.385 0.938,0.438 10 false Crank Position Sensor 3.271,1.969 4.208,2.406 0.938,0.438 10 false Crank Position Sensor 1.729,2.792 2.281,3.104 0.552,0.313 10 false 30°CA 2.208,2.802 2.76,3.115 0.552,0.313 10 false 10°CA 4.542,2.75 5.094,3.063 0.552,0.313 10 false 180°CA 5.271,2.75 5.823,3.063 0.552,0.313 10 false 360°CA 5.958,2.75 6.51,3.063 0.552,0.313 10 false 180°CA 5.208,0.917 5.76,1.229 0.552,0.313 10 false 720°CA



c.

Camshaft Timing Oil Control Valve Assembly

i.

This camshaft timing oil control valve assembly controls the spool valve using duty cycle control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller advance or retard side. When the engine is stopped, the camshaft timing oil control valve assembly will move to the retard position.

W104588E07
2.844,0.917 2.552,0.625 2.552,0.625 2.417,0.625 true 3.188,0.917 3.469,0.625 3.469,0.625 3.615,0.625 true 2.229,1.531 1.583,2.083 1.583,2.083 1.479,2.083 true 2.26,1.354 1.594,0.938 1.594,0.938 1.51,0.938 true 3.615,1.542 4.052,2.094 4.052,2.094 4.135,2.094 true 2.24,0.521 2.479,0.708 0.24,0.188 10 false *a 1.354,0.865 1.594,1.052 0.24,0.188 10 false *2 1.323,2 1.563,2.188 0.24,0.188 10 false *1 4.146,2.01 4.385,2.198 0.24,0.188 10 false *3 3.646,0.542 3.885,0.729 0.24,0.188 10 false *b 2.615,2.052 2.854,2.24 0.24,0.188 10 false *c 3.271,2.052 3.51,2.24 0.24,0.188 10 false *c 2.938,2.052 3.177,2.24 0.24,0.188 10 false *d

Text in Illustration
*1 Spring *2 Sleeve
*3 Spool Valve - -
*a To Intake VVT-i Controller (Advance Side) *b To Intake VVT-i Controller (Retard Side)
*c Drain *d Oil Pressure



d.

Knock control sensor (Flat Type)

i.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking frequency of the engine block. This sensor can only detect vibration in this frequency band.


ii.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 6 kHz to 15 kHz). It has the following features.


iii.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100530E28
3.406,2.948 3.917,2.51 3.917,2.51 4.042,2.51 true 3.417,1.813 3.927,1.385 3.927,1.385 4.063,1.385 true 0.146,0.073 3.26,0.448 3.115,0.375 12 false Characteristics of Knock Control Sensor : 0.906,0.625 4.698,0.917 3.792,0.292 10 false : Resonance Characteristic of Conventional Type (Resonant) 0.906,0.948 4.49,1.24 3.583,0.292 10 false : Resonance Characteristic of Flat Type (Non-resonant) 1.563,1.354 1.781,1.604 0.219,0.25 10 false (V) 1.135,2.24 1.635,2.438 0.5,0.198 10 false Voltage 3.083,3.333 3.76,3.5 0.677,0.167 10 false Frequency 5.26,3.156 5.573,3.406 0.313,0.25 10 false (Hz) 4.083,2.417 5.917,2.604 1.833,0.188 10 false Detection Band of Flat Type 4.115,1.281 6.281,1.5 2.167,0.219 10 false Detection Band of Resonant Type


iv.

A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.


v.

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.


vi.

An open/short circuit detection resistor is integrated in the sensor. When the ignition is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W104701E10
1.094,1.969 0.865,1.354 0.865,1.354 0.74,1.354 true 1.135,1.875 0.99,1.042 0.99,1.042 0.823,1.042 true 1.167,1.781 1.229,0.865 1.229,0.865 1.375,0.865 true 2.323,1.948 2.438,1.125 2.438,1.125 2.563,1.125 true 5.708,1.542 6.073,0.938 6.073,0.938 6.198,0.938 true 5.76,1.573 6.083,1.896 6.083,1.896 6.229,1.896 true 0.448,0.313 0.708,0.542 0.26,0.229 10 false *A 4.729,0.333 4.99,0.563 0.26,0.229 10 false *B 0.563,1.26 0.823,1.49 0.26,0.229 10 false *3 6.219,0.823 6.479,1.052 0.26,0.229 10 false *3 6.26,1.802 6.521,2.031 0.26,0.229 10 false *5 0.667,0.927 0.927,1.156 0.26,0.229 10 false *2 1.385,0.74 1.646,0.969 0.26,0.229 10 false *1 2.604,1.01 2.865,1.24 0.26,0.229 10 false *4

Text in Illustration
*A Flat Type Knock Control Sensor (Non-Resonant Type) *B Conventional Type Knock Control Sensor (Resonant Type)
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open Circuit Detection Resistor
*5 Vibration Plate - -

W101046E12
0.885,0.49 2.906,0.813 2.021,0.323 10 false Flat Type Knock Control Sensor 3.979,1.094 4.396,1.417 0.417,0.323 10 false KNK1 3.958,1.74 4.417,2.063 0.458,0.323 10 false EKNK 5.094,1.292 5.448,1.604 0.354,0.313 10 false ECM 2.177,1.313 2.656,1.594 0.479,0.281 10 false 200kΩ 1.719,2.052 4.094,2.354 2.375,0.302 10 false Open/Short Circuit Detection Resistor 0.76,2.354 2.208,2.667 1.448,0.313 10 false Piezoelectric Element


vii.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W101072E17
3.594,1.302 2.917,1.167 2.917,1.167 2.823,1.167 true 3.604,0.969 2.938,0.292 2.938,0.292 2.865,0.292 true 2.656,1.083 2.854,1.313 0.198,0.229 10 false *2 2.688,0.208 2.885,0.438 0.198,0.229 10 false *1

Text in Illustration
*1 Steel Weight *2 Piezoelectric Element
V100135

Inertia - -



e.

Intake Mass Air Flow Meter Sub-assembly

i.

The compact and lightweight intake mass air flow meter sub-assembly, which is a plug-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance has been reduced.


ii.

This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.

W103925E10
2.01,1.083 1.188,2.083 1.188,2.083 1.031,2.083 true 2.417,1.458 1.781,2.323 1.781,2.323 1.635,2.323 true 4.438,1.375 4.854,1.875 4.854,1.875 5,1.875 true 0.854,1.969 1.042,2.271 0.188,0.302 10 false *1 1.469,2.219 1.656,2.521 0.188,0.302 10 false *2 5.031,1.771 5.219,2.073 0.188,0.302 10 false *3

Text in Illustration
*1 Temperature Sensing Element *2 Hot-wire Element
*3 Intake Air Temperature Sensor - -
V100135

Air Flow - -



f.

Throttle Position Sensor

i.

The throttle position sensor is mounted on the throttle with motor body to detect the opening angle of the throttle valve. The throttle position sensor converts the magnetic flux density that changes when the magnetic yoke (located on the same axis as the throttle shaft) rotates around the Hall IC into electric signals to operate the throttle control motor.

W103926E12
3.729,0.708 3.354,0.208 3.354,0.208 3.208,0.208 true 2.531,2.885 2.156,3.385 2.156,3.385 2.01,3.385 true 4.406,2.115 4.531,3 4.531,3 4.677,3 true 4.24,2.135 4.458,3.417 4.458,3.417 4.604,3.417 true 3.042,0.125 3.219,0.427 0.177,0.302 10 false *1 1.833,3.302 2.01,3.604 0.177,0.302 10 false *2 4.708,2.938 4.885,3.24 0.177,0.302 10 false *3 4.625,3.354 4.802,3.656 0.177,0.302 10 false *4

Text in Illustration
*1 Throttle Control Motor *2 Throttle Position Sensor
*3 Throttle Valve *4 Return Spring

W103927E16
1.594,1.604 1.594,1.104 1.594,1.104 1.458,1.104 true 0.563,1.885 1.542,1.885 true 0.594,2.427 1.542,2.427 true 1.573,3.052 1.573,2.76 true 0.708,0.604 2.865,1.01 2.156,0.406 10 false Throttle Position Sensor 0.927,1.031 1.417,1.344 0.49,0.313 10 false Magnet 2.448,1.417 2.823,1.594 0.375,0.177 10 false VTA1 4.323,0.833 4.531,1.052 0.208,0.219 10 false V 4.563,1.323 4.948,1.531 0.385,0.208 10 false VTA2 4.583,3.146 6.448,3.479 1.865,0.333 10 false Throttle Valve Opening Angle 5.51,1.667 5.896,1.875 0.385,0.208 10 false VTA1 3.635,1.448 4.167,2.188 0.531,0.74 10 false Output Voltage 3.969,2.469 4.906,3.146 0.938,0.677 10 false Throttle Valve Fully Close 6.115,2.458 7.052,3.135 0.938,0.677 10 false Throttle Valve Fully Open 4.219,1.073 4.417,1.271 0.198,0.198 10 false 5 4.219,1.281 4.417,1.479 0.198,0.198 10 false 4 4.208,1.5 4.406,1.698 0.198,0.198 10 false 3 4.208,1.719 4.406,1.917 0.198,0.198 10 false 2 4.208,1.917 4.406,2.115 0.198,0.198 10 false 1 4.198,2.146 4.396,2.344 0.198,0.198 10 false 0 4.531,2.229 4.729,2.427 0.198,0.198 10 false 10 4.802,2.229 5,2.427 0.198,0.198 10 false 20 5.031,2.229 5.229,2.427 0.198,0.198 10 false 30 5.271,2.24 5.469,2.438 0.198,0.198 10 false 40 5.521,2.24 5.719,2.438 0.198,0.198 10 false 50 5.771,2.24 5.969,2.438 0.198,0.198 10 false 60 6.021,2.24 6.219,2.438 0.198,0.198 10 false 70 6.26,2.24 6.458,2.438 0.198,0.198 10 false 80 6.531,2.24 6.729,2.438 0.198,0.198 10 false 90 2.552,1.813 2.844,2.083 0.292,0.271 10 false E2 2.542,2.198 2.823,2.417 0.281,0.219 10 false VC 2.427,2.688 2.802,2.885 0.375,0.198 10 false VTA2 3,2.021 3.365,2.354 0.365,0.333 10 false ECM 0.115,1.781 0.594,2.115 0.479,0.333 10 false Hall IC 0.146,2.333 0.625,2.667 0.479,0.333 10 false Hall IC 1.344,3.031 1.854,3.365 0.51,0.333 10 false Magnet



g.

Oxygen Sensor

i.

A cup type oxygen sensor is used.


ii.

The cup type oxygen sensor contains a sensor element that surrounds the heater.


iii.

The output voltage of the oxygen sensor changes in accordance with the oxygen concentration in the exhaust emission. The ECM uses this output voltage to determine whether the present air fuel ratio is richer or leaner than the stoichiometric air fuel ratio.

W105027E02
3.948,2.698 4.26,3.24 4.26,3.24 4.427,3.24 true 3.917,1.719 4.177,0.729 4.177,0.729 4.323,0.729 true 4.063,1.76 4.458,1.083 4.458,1.083 4.625,1.083 true 3.688,2.625 3.25,3.073 3.25,3.073 3.063,3.073 true 3.833,2.708 3.479,3.396 3.479,3.396 3.292,3.396 true 4.354,0.656 4.594,0.844 0.24,0.188 10 false *1 4.646,0.979 4.885,1.167 0.24,0.188 10 false *2 4.458,3.135 4.698,3.323 0.24,0.188 10 false *3 3.135,3.292 3.375,3.479 0.24,0.188 10 false *4 2.885,2.969 3.125,3.156 0.24,0.188 10 false *3

Text in Illustration
*1 Heater *2 Atmosphere
*3 Platinum Electrode *4 Sensor Element (Zirconia)



h.

Accelerator Pedal Sensor Assembly

i.

The non-contact type accelerator pedal sensor assembly uses a Hall IC.


ii.

The magnetic yoke that is mounted at the accelerator pedal arm rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur at that time into electrical signals, and outputs them as accelerator pedal effort to the ECM.


iii.

The Hall IC contains circuits for the main and sub signals. It converts the accelerator pedal depressed angles into electric signals with two differing characteristics and outputs them to the ECM.

W111013E03
4.938,1.552 4.594,1.25 4.594,1.25 4.406,1.25 true 5.083,3.865 4.594,3.448 4.594,3.448 4.406,3.448 true 5.083,3.417 4.594,3 4.594,3 4.406,3 true 5.604,3.25 5.792,2.833 5.792,2.833 5.979,2.833 true 5.146,3.677 6.094,3.344 6.094,3.344 6.281,3.344 true 5.635,2.042 5.823,2.188 5.823,2.188 6,2.188 true 2.469,1.417 2.667,1.635 0.198,0.219 10 false A 0.802,1.875 1,2.094 0.198,0.219 10 false A 3.917,0.292 4.198,0.542 0.281,0.25 10 false *a 3.917,2.75 4.198,3 0.281,0.25 10 false *b 4.229,1.177 4.51,1.427 0.281,0.25 10 false *1 6.042,2.115 6.323,2.365 0.281,0.25 10 false *2 6.031,2.75 6.313,3 0.281,0.25 10 false *2 6.323,3.281 6.604,3.531 0.281,0.25 10 false *4 4.219,2.927 4.5,3.177 0.281,0.25 10 false *3 4.219,3.375 4.5,3.625 0.281,0.25 10 false *3

Text in Illustration
*1 Magnetic Yoke *2 Accelerator Pedal Arm
*3 Magnet *4 Hall IC
*a Internal Construction *b A-A Cross Section

W103928E10
1.208,1.104 1.365,1.104 1.365,1.104 1.542,1.573 true 1.198,3.052 1.354,3.052 1.354,3.052 1.531,2.583 true 0.125,0.458 2.917,0.854 2.792,0.396 10 false Accelerator Pedal Sensor Assembly 0.698,1.031 1.271,1.333 0.573,0.302 10 false Magnet 0.677,2.938 1.229,3.24 0.552,0.302 10 false Magnet 1.073,1.75 1.604,2.042 0.531,0.292 10 false Hall IC 1.063,2.104 1.594,2.396 0.531,0.292 10 false Hall IC 2.385,1.156 2.781,1.365 0.396,0.208 10 false VPA1 2.448,1.469 2.781,1.667 0.333,0.198 10 false EPA 2.365,1.771 2.792,1.969 0.427,0.198 10 false VCPA 2.365,1.99 2.771,2.198 0.406,0.208 10 false VPA2 2.375,2.281 2.76,2.479 0.385,0.198 10 false EPA2 2.344,2.573 2.76,2.771 0.417,0.198 10 false VCP2 2.979,1.865 3.365,2.083 0.385,0.219 10 false ECM 4.115,0.802 4.302,0.99 0.188,0.188 10 false V 3.99,1.042 4.156,1.229 0.167,0.188 10 false 5 3.583,1.479 4.125,2.167 0.542,0.688 10 false Output Voltage 4.01,2.74 4.167,2.938 0.156,0.198 10 false 0 4.146,2.917 4.896,3.25 0.75,0.333 10 false Fully Close 4.365,3.271 6.625,3.615 2.26,0.344 10 false Accelerator Pedal Depressed Angle 6.156,2.906 6.906,3.24 0.75,0.333 10 false Fully Open 5.042,1.49 5.469,1.688 0.427,0.198 10 false VPA2 5.542,2.052 6,2.25 0.458,0.198 10 false VPA1 3.865,2.469 4.115,2.667 0.25,0.198 10 false 0.8 3.865,2.198 4.125,2.396 0.26,0.198 10 false 1.6



i.

No. 1 Ignition Coil

i.

An igniter is integrated with the ignition coils, which are provided independently in each cylinder. This improves ignition timing accuracy, reduces high-voltage loss and enhances the overall reliability of the ignition system by eliminating the distributor.


ii.

In addition, a spark plug cap, to which a spark plug is fitted, is also integrated with the ignition coils, contributing to the simplification of the ignition system.

W104593E07
3.594,0.917 4.021,0.479 4.021,0.479 4.125,0.479 true 2.698,1.531 2.802,1.531 2.802,1.531 3.479,1.719 true 3.604,1.896 4.26,1.677 4.26,1.677 4.385,1.677 true 3.646,2.219 4.094,2.844 4.094,2.844 4.24,2.844 true 3,3.354 3.115,3.354 3.115,3.354 3.385,3.073 true 4.146,0.406 4.365,0.594 0.219,0.188 10 false *1 2.531,1.438 2.75,1.625 0.219,0.188 10 false *2 2.833,3.271 3.052,3.458 0.219,0.188 10 false *5 4.25,2.771 4.469,2.958 0.219,0.188 10 false *4 4.417,1.615 4.635,1.802 0.219,0.188 10 false *3

Text in Illustration
*1 Igniter *2 Iron Core
*3 Secondary Coil *4 Primary Coil
*5 Spark Plug Cap - -




OPERATION


a.

Variable Valve Timing-intelligent (VVT-i) System

i.

Using the engine speed, vehicle speed, intake air mass, throttle position and water temperature, the ECM can calculate optimal valve timing for each driving condition (target valve timing). The ECM uses this calculated timing to control the camshaft timing oil control valves. In addition, the ECM uses signals from the cam position sensor and the crank position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W104703E10
0.229,0.552 2.135,0.906 1.906,0.354 10 false Crank Position Sensor 0.229,1.073 1.948,1.76 1.719,0.688 10 false Intake Mass Air Flow Meter Sub-assembly 0.229,1.927 1.833,2.615 1.604,0.688 10 false Throttle Position Sensor 0.229,2.792 1.615,3.469 1.385,0.677 10 false E.F.I. Engine Coolant Temperature Sensor 0.229,3.583 2.135,3.958 1.906,0.375 10 false Cam Position Sensor 0.229,4.094 2.135,4.469 1.906,0.375 10 false Vehicle Speed Signal 3.771,2.594 4.594,2.969 0.823,0.375 10 false Correction 4.365,1.427 5.083,1.802 0.719,0.375 10 false Feedback 5.125,0.969 5.844,1.5 0.719,0.531 10 false Duty-cycle Control 5.865,0.698 6.927,2.25 1.063,1.552 10 false Camshaft Timing Oil Control Valve Assembly 3.396,0.667 4.865,1.042 1.469,0.375 10 false Target Valve Timing 3.49,3.115 4.833,3.49 1.344,0.375 10 false Actual Valve Timing 3.917,3.781 4.427,4.156 0.51,0.375 10 false ECM


ii.

When the camshaft timing oil control valve is operated as illustrated below by the advance signal from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

W105063E06
0.604,2.292 0.458,2.594 0.458,2.594 0.323,2.594 true 0.479,1.458 0.375,1.156 0.375,1.156 0.25,1.156 true 5.271,2.906 4.74,2.906 true 0.083,1.083 0.333,1.281 0.25,0.198 10 false *1 0.167,2.51 0.417,2.708 0.25,0.198 10 false *a 5.198,3 5.448,3.198 0.25,0.198 10 false *b 5.5,3 5.75,3.198 0.25,0.198 10 false *c 4.573,2.823 4.823,3.021 0.25,0.198 10 false *d 6.646,1.177 6.896,1.375 0.25,0.198 10 false *e

Text in Illustration
*1 Vane - -
*a Rotational Direction *b In
*c Drain *d Oil Pressure
*e from ECM - -


iii.

When the camshaft timing oil control valve is operated as illustrated below by the retard signal from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

W105064E07
5.281,2.875 5.75,2.875 true 0.427,2.677 0.552,2.677 0.552,2.677 0.625,2.302 true 0.479,1.427 0.396,1 0.396,1 0.281,1 true 0.104,0.927 0.417,1.125 0.313,0.198 10 false *1 0.25,2.594 0.563,2.792 0.313,0.198 10 false *a 4.906,3 5.219,3.198 0.313,0.198 10 false *b 5.229,3 5.542,3.198 0.313,0.198 10 false *c 5.771,2.792 6.083,2.99 0.313,0.198 10 false *d 6.635,1.146 6.948,1.344 0.313,0.198 10 false *e

Text in Illustration
*1 Vane - -
*a Rotational Direction *b Drain
*c In *d Oil Pressure
*e from ECM - -


iv.

After reaching the target timing, the valve timing is held by keeping the camshaft timing oil control valve assembly in the neutral position unless the traveling state changes. This adjusts the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.



b.

Fuel Pump Control

i.

The fuel pump control is used to stop the fuel pump when the airbags deploy in a front or side collision.


ii.

In this system, the airbag deployment signal from the airbag sensor assembly is detected by the ECM, which turns off the circuit opening relay.


iii.

After the fuel cut control has been activated, turning the ignition switch from off to ON cancels the fuel cut control, and the engine can be restarted.

W104984E07
0.156,0.667 1.521,1.302 1.365,0.635 10 false Side Airbag Sensor Assembly 0.156,1.677 1.521,2.25 1.365,0.573 10 false No. 2 Side Airbag Sensor Assembly 2.063,1.542 2.75,2.802 0.688,1.26 10 false Airbag Sensor Assembly 4.042,1.781 4.594,2.177 0.552,0.396 10 false ECM 2.896,2.073 3.833,2.469 0.938,0.396 10 false CAN (V Bus) 4.875,0.563 5.646,0.958 0.771,0.396 10 false IG2 Relay 5.833,0.573 6.917,0.969 1.083,0.396 10 false EFI Main Relay 5.938,1.427 7.042,2.104 1.104,0.677 10 false Circuit Opening Relay 5.927,2.396 7.094,2.813 1.167,0.417 10 false Fuel Pump Motor 0.156,2.698 1.521,3.271 1.365,0.573 10 false Front Airbag Sensor



c.

Cooling Fan Control

i.

On the models without air conditioning system, the ECM controls the operation of the cooling fan based on the E.F.I. engine coolant temperature sensor signal.


ii.

On the models with air conditioning system, the ECM controls the operation of the cooling fan in two speeds (low and high) based on the E.F.I. engine coolant temperature sensor signal and the air conditioning amplifier assembly signal. The low speed operation is accomplished by applying the current through a resistor, which reduces the speed of the cooling fan.

W100970E13
0.24,1.521 1.896,2.135 1.656,0.615 10 false Air Conditioning Amplifier Assembly 0.219,0.667 1.875,1.292 1.656,0.625 10 false E.F.I. Engine Coolant Temperature Sensor 2.01,1.958 2.875,2.375 0.865,0.417 10 false CAN (V Bus) 4.521,0.125 4.813,0.323 0.292,0.198 10 false IG1 4.885,0.125 5.292,0.344 0.406,0.219 10 false BATT 5.135,0.583 7,0.938 1.865,0.354 10 false Cooling Fan Relay 5.135,0.99 6.708,1.344 1.573,0.354 10 false Cooling Fan Motor 5.135,1.469 6.958,1.813 1.823,0.344 10 false No.2 Cooling Fan Relay 5.115,1.896 6.677,2.281 1.563,0.385 10 false Cooling Fan Resistor 3.281,1.042 3.688,1.396 0.406,0.354 10 false ECM

Engine Coolant Temperature Cooling Fan Drive Request Signal Cooling Fan Operation
Low Off Off
Low Low
High High
High Off High
Low High
High High




FAIL-SAFE


a.

When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory. For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section. For details, refer to the Repair Manual.