Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE UNIT
NM19S0E _51 Engine / Hybrid System _051393 2NZ-FE ENGINE MECHANICAL _0247858 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

2NZ-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Cylinder Head Sub-assembly

i.

The fuel injector assemblies are installed in the cylinder head sub-assembly to reduce the distance from the fuel injector assembly to the intake valve, thus it prevents the fuel from adhering to the intake port walls, and reduces exhaust emissions.


ii.

The routing of the water jacket in the cylinder head sub-assembly is optimized to achieve high cooling performance.


iii.

Through the use of the taper squish combustion chamber, the engine's knocking resistance and fuel efficiency have been improved.

W104601E05
4.625,0.552 5.115,0.365 5.115,0.365 5.219,0.365 true 3.146,1.771 3.573,2.51 3.573,2.51 4.552,2.51 true 3.813,1.771 4.188,2.51 true 4.229,1.427 4.573,1.656 4.573,1.656 4.708,1.656 true 4,1.823 4.573,1.656 true 2.219,1.177 2.479,1.417 0.26,0.24 10 false *a 4.844,0.813 5.104,1.052 0.26,0.24 10 false *b 5.25,0.302 5.51,0.542 0.26,0.24 10 false *1 4.729,1.573 4.99,1.813 0.26,0.24 10 false *2 4.573,2.427 4.833,2.667 0.26,0.24 10 false *c

Text in Illustration
*1 Fuel Injector Assembly *2 Water Jacket
*a Exhaust Side *b Intake Side
*c Taper Squish - -



b.

Cylinder Block Sub-assembly

i.

Lightweight aluminum alloy is used for the cylinder block sub-assembly.


ii.

The liners are the spiny-type, which have been manufactured so that their casting exterior forms a large irregular surface in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps improve heat dissipation, resulting in a lower overall temperature and heat deformation of the cylinder bores.

W104602E05
4.542,1.823 4.646,1.823 4.646,1.823 5.031,2.125 true 6,2.427 5.896,2.427 5.896,2.427 5.604,2.135 true 5.771,1.333 5.979,1.083 5.979,1.083 6.083,1.083 true 4.302,0.698 4.594,0.948 0.292,0.25 10 false *a 4.375,1.708 4.635,1.927 0.26,0.219 10 false *1 6.115,0.958 6.365,1.167 0.25,0.208 10 false *2 6.021,2.333 6.281,2.552 0.26,0.219 10 false *3 2.354,0.875 2.521,1.063 0.167,0.188 10 true A 2.031,0.708 2.198,0.896 0.167,0.188 10 false A

Text in Illustration
*1 Irregularly Shaped Outer Casting Surface of Liner *2 Cylinder Block Sub-assembly
*3 Spiny Type Liner - -
*a A-A Cross Section - -


iii.

Through the use of an offset crankshaft, the centerline of the cylinder bores is shifted 12 mm (0.47 in.) towards the intake in relation to the centerline of the crankshaft. Thus, the side force (thrust) applied to the cylinder walls is reduced when maximum combustion pressure is applied. This contributes to fuel economy.

W105059E04
4.302,2.344 3.813,1.5 3.813,1.5 3.698,1.5 true 5.75,2.344 5.25,1.656 5.25,1.656 5.135,1.656 true 1.49,1.01 1.74,1.302 0.25,0.292 10 false *a 1.938,0.615 2.188,0.906 0.25,0.292 10 false *b 3.531,1.417 3.781,1.708 0.25,0.292 10 false *c 1.865,3.198 2.115,3.49 0.25,0.292 10 false *c 4.344,3.188 4.594,3.479 0.25,0.292 10 false *e 5.781,3.198 6.031,3.49 0.25,0.292 10 false *f 4.333,0.281 4.583,0.573 0.25,0.292 10 false *d 5.635,0.292 5.885,0.583 0.25,0.292 10 false *d 4.969,1.563 5.219,1.854 0.25,0.292 10 false *c

Text in Illustration
*a 12 mm (0.472 in.) *b Bore Centerline
*c Crankshaft Centerline *d Maximum Pressure
*e Offset Crankshaft *f Non-offset Crankshaft



c.

Oil Pan Sub-assembly

i.

The oil pan sub-assembly is made of aluminum die-cast.

W103937E05
2.5,1.344 1.552,0.521 1.552,0.521 1.385,0.521 true 2.875,2.958 1.927,2.51 1.927,2.51 1.771,2.51 true 3.938,3.75 5.135,3.156 5.135,3.156 5.333,3.156 true 1.188,0.438 1.344,0.615 0.156,0.177 10 false *1 1.563,2.427 1.719,2.604 0.156,0.177 10 false *2 5.396,3.104 5.552,3.281 0.156,0.177 10 false *3

Text in Illustration
*1 Oil Pan Sub-assembly *2 Oil Strainer Sub-assembly
*3 No. 2 Oil Pan Sub-assembly - -



d.

Piston

i.

The pistons are made of aluminum alloy to allow them to be compact and lightweight.


ii.

The piston head portion uses a taper squish shape to achieve fuel combustion efficiency.


iii.

Semi-floating type piston pins are used.


iv.

By increasing the machining precision of the cylinder bore diameter, only one size of piston is available.

W105020E04
1.573,0.594 3.24,0.594 3.24,0.594 3.385,0.958 true 2,0.958 1.885,0.604 true 5.24,1.177 5.625,0.792 5.625,0.792 5.813,0.792 true 5.219,1.635 5.604,1.448 5.604,1.448 5.781,1.448 true 5.198,2.073 5.594,2.281 5.594,2.281 5.771,2.281 true 1.406,0.479 1.625,0.677 0.219,0.198 10 false *a 5.833,0.708 6.052,0.906 0.219,0.198 10 false *1 5.823,1.375 6.042,1.573 0.219,0.198 10 false *2 5.813,2.219 6.031,2.417 0.219,0.198 10 false *3

Text in Illustration
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*3 Oil Ring - -
*a Taper Squish Shape - -



e.

Connecting Rod Sub-assembly

i.

The connecting rod sub-assemblies and caps are made of high strength steel for weight reduction.


ii.

Plastic region tightening bolts are used to achieve a light weight.

W104604E04
3.01,3.125 3.156,3.458 3.156,3.458 4.813,3.458 true 3.885,3.125 4.031,3.458 true 4.844,3.365 5.063,3.583 0.219,0.219 10 false *1

Text in Illustration
*1 Plastic Region Tightening Bolt - -



f.

Crankshaft

i.

The diameter and width of the pins and journals have been reduced, and the pins for the no. 1 and no. 4 cylinders have been made highly rigid to achieve a lightweight and low-friction performance.


ii.

The crankshaft has 5 journals and 4 balance weights.


iii.

A crank position sensor rotor is pressed into the crankshaft to realize an integrated configuration.

W105013E07
1.813,0.99 1.323,0.302 1.323,0.302 1.177,0.302 true 2.438,0.802 2.729,0.302 2.729,0.302 2.865,0.302 true 4.969,0.781 5.24,0.313 5.24,0.313 5.385,0.313 true 5.385,1.198 5.656,0.635 5.656,0.635 5.792,0.635 true 2.073,1.635 1.656,2.417 1.656,2.417 1.521,2.417 true 2.917,1.604 2.552,2.396 2.552,2.396 2.417,2.396 true 4.51,1.615 4.865,2.406 4.865,2.406 5,2.406 true 3.656,1.625 4.042,2.417 4.042,2.417 4.177,2.417 true 5.219,2.135 5.5,2.427 5.5,2.427 5.635,2.427 true 2.885,0.198 3.125,0.385 0.24,0.188 10 false *2 1.021,0.229 1.26,0.417 0.24,0.188 10 false *1 5.427,0.24 5.667,0.427 0.24,0.188 10 false *7 5.813,0.573 6.052,0.76 0.24,0.188 10 false *8 5.667,2.365 5.906,2.552 0.24,0.188 10 false *9 5.063,2.333 5.302,2.521 0.24,0.188 10 false *6 4.219,2.344 4.458,2.531 0.24,0.188 10 false *5 2.26,2.333 2.5,2.521 0.24,0.188 10 false *4 1.354,2.333 1.594,2.521 0.24,0.188 10 false *3

Text in Illustration
*1 Crankshaft Position Sensor Rotor *2 Oil Hole
*3 No. 1 Journal *4 No. 2 Journal
*5 No. 3 Journal *6 No. 4 Journal
*7 Crank Pin *8 No. 5 Journal
*9 Balance Weight - -



g.

Valve Mechanism

i.

The shimless type valve lifter is used to increase the amount of the valve lift.


ii.

The intake and exhaust camshafts are driven by a chain sub-assembly.


iii.

The VVT-i system is used to realize fuel economy, engine performance and reduce exhaust emissions. For details of VVT-i control.

W104605E05
0.76,1.5 0.844,1.5 0.844,1.5 1.542,1.917 true 1.219,0.781 1.302,0.781 1.302,0.781 1.479,1.396 true 0.698,2.281 0.781,2.281 0.781,2.281 1.302,2.521 true 0.802,3.729 0.896,3.729 0.896,3.729 1.448,3.302 true 1.865,3.104 2.271,4.302 2.271,4.302 2.365,4.302 true 3.906,1.521 4.156,1.844 4.156,1.844 4.281,1.844 true 2.667,1.385 2.854,0.594 2.854,0.594 3.01,0.594 true 5.771,2.083 6.115,2.375 6.115,2.375 6.219,2.375 true 5.521,3.531 6.042,3.25 6.042,3.25 6.146,3.25 true 1.063,0.708 1.323,0.927 0.26,0.219 10 false *1 0.594,1.417 0.854,1.635 0.26,0.219 10 false *2 0.542,2.208 0.802,2.427 0.26,0.219 10 false *3 0.635,3.646 0.896,3.865 0.26,0.219 10 false *4 2.385,4.24 2.646,4.458 0.26,0.219 10 false *5 3.042,0.5 3.302,0.719 0.26,0.219 10 false *6 4.323,1.792 4.583,2.01 0.26,0.219 10 false *7 6.26,2.302 6.521,2.521 0.26,0.219 10 false *8 6.177,3.188 6.438,3.406 0.26,0.219 10 false *9

Text in Illustration
*1 Chain Sub-assembly *2 Camshaft Timing Gear Assembly
*3 No. 1 Chain Tensioner Assembly *4 Chain Tensioner Slipper
*5 No. 1 Chain Vibration Damper *6 No. 2 Camshaft
*7 Camshaft *8 Valve Lifter
*9 Valve - -



h.

Camshaft

i.

Oil passages are provided in the camshaft in order to supply engine oil pressure to the VVT-i system.


ii.

A VVT-i Controller (camshaft timing gear assembly) is provided on the front of the camshaft to vary the timing of the intake valves.


iii.

A timing rotor is provided behind the camshaft to trigger the cam position sensor.

W104606E04
0.979,2.5 1.115,2.5 1.115,2.5 1.302,2.688 true 2.458,0.802 2.583,0.802 2.583,0.802 2.781,1.26 true 5.76,1.74 6.021,1.365 6.021,1.365 6.104,1.365 true 4.563,2.25 5.021,2.583 5.021,2.583 5.125,2.583 true 4.198,3.458 4.417,2.844 4.417,2.844 4.51,2.844 true 4.313,3.74 4.74,4.156 4.74,4.156 4.833,4.156 true 0.813,2.427 1.031,2.635 0.219,0.208 10 false *1 2.271,0.729 2.49,0.938 0.219,0.208 10 false *2 6.125,1.281 6.344,1.49 0.219,0.208 10 false *3 5.156,2.521 5.375,2.729 0.219,0.208 10 false *4 4.521,2.74 4.74,2.948 0.219,0.208 10 false *a 4.854,4.073 5.073,4.281 0.219,0.208 10 false *b

Text in Illustration
*1 VVT-i Controller (Camshaft Timing Gear Assembly) *2 No. 2 Camshaft
*3 Timing Rotor *4 Camshaft
*a Oil Passage (Advance) *b Oil Passage (Retard)



i.

VVT-I Controller (Camshaft timing gear assembly)

i.

The VVT-i controller (camshaft timing gear assembly) consists of the housing driven from the chain sub-assembly and the vane coupled with the camshaft.


ii.

The oil pressure sent from the advance or retard side path at the camshaft causes rotation in the VVT-i controller (camshaft timing gear assembly) vane circumferential direction to vary the intake valve timing continuously.


iii.

When the engine is stopped, the camshaft will be in the most retarded state to ensure startability.


iv.

When hydraulic pressure is not applied to the VVT-i controller (camshaft timing gear assembly) immediately after the engine has been started, the lock pin locks the movement of the VVT-i controller (camshaft timing gear assembly) to prevent a knocking noise.

W104607E05
2.844,0.542 2.979,0.542 2.979,0.542 3.417,0.917 true 3.958,0.969 4.344,0.427 4.344,0.427 4.448,0.427 true 5.01,0.896 5.26,0.5 5.26,0.5 5.365,0.5 true 4.01,1.271 4.625,1.813 4.625,1.813 4.75,1.813 true 2.792,2.458 3,2.667 0.208,0.208 10 false *a 3.313,3.208 3.521,3.417 0.208,0.208 10 false *b 4.188,3.208 4.396,3.417 0.208,0.208 10 false *c 5.115,2.865 5.323,3.073 0.208,0.208 10 false *d 2.677,0.458 2.885,0.667 0.208,0.208 10 false *1 4.5,0.354 4.708,0.563 0.208,0.208 10 false *2 5.396,0.427 5.604,0.635 0.208,0.208 10 false *3 4.781,1.74 4.99,1.948 0.208,0.208 10 false *4

Text in Illustration
*1 Housing *2 Lock pin
*3 Camshaft *4 Vane
*a Lock Pin Operation *b Engine Stopped
*c Engine Operating *d Oil Pressure



j.

Chain Sub-assembly and No. 1 Chain Tensioner Assembly

i.

A roller type chain sub-assembly with an 8.0 mm (0.315 in.) pitch is used to make the engine compact and reduce noise.


ii.

The chain sub-assembly is lubricated by an oil jet.


iii.

The no. 1 chain tensioner assembly uses a spring and oil pressure to maintain proper chain tensioner at all times. The no. 1 chain tensioner assembly suppresses noise generated by the timing chain sub-assembly.


iv.

A ratchet type non-return mechanism is used in the no. 1 chain tensioner assembly.

W104608E05
1.531,1.063 1.656,1.063 1.656,1.063 2.219,1.719 true 2.042,1.844 1.302,2.656 1.302,2.656 1.208,2.656 true 2.5,2.365 2.76,2.844 2.76,2.844 2.875,2.844 true 2.833,2.167 3.104,2.302 3.104,2.302 3.24,2.302 true 2.917,1.688 3.135,1.302 3.135,1.302 3.271,1.302 true 5.458,0.771 5.698,0.531 5.698,0.531 5.917,0.531 true 5.042,1.938 5.313,2.25 5.313,2.25 5.469,2.25 true 3.948,3.135 4.083,3.135 4.083,3.135 4.438,2.792 true 4.75,2.75 5.135,3.135 5.135,3.135 5.302,3.135 true 1.354,0.99 1.573,1.198 0.219,0.208 10 false *1 3.323,1.219 3.542,1.427 0.219,0.208 10 false *2 5.958,0.438 6.177,0.646 0.219,0.208 10 false *6 5.521,2.167 5.74,2.375 0.219,0.208 10 false *7 5.323,3.083 5.542,3.292 0.219,0.208 10 false *9 3.771,3.063 3.99,3.271 0.219,0.208 10 false *8 3.26,2.208 3.479,2.417 0.219,0.208 10 false *3 2.917,2.802 3.135,3.01 0.219,0.208 10 false *4 1.031,2.573 1.25,2.781 0.219,0.208 10 false *5

Text in Illustration
*1 Spring *2 Plunger
*3 Cam *4 Cam Spring
*5 Check Ball *6 Chain Sub-assembly
*7 No. 1 Chain Vibration Damper *8 Chain Tensioner Slipper
*9 Oil Jet - -



k.

Timing Chain Cover (Oil Pump Assembly)

i.

A single-piece, aluminum die-cast timing chain cover (oil pump assembly) that entirely seals the front portion of the cylinder block sub-assembly and cylinder head sub-assembly is used.

W104609E05
0.823,2.073 0.938,2.073 0.938,2.073 1.5,1.438 true 4.438,2.74 4.563,2.74 4.563,2.74 5.333,2.25 true 0.646,1.99 0.875,2.198 0.229,0.208 10 false *1 1.823,3 2.052,3.208 0.229,0.208 10 false *a 5.25,3 5.479,3.208 0.229,0.208 10 false *b 4.25,2.656 4.479,2.865 0.229,0.208 10 false *2

Text in Illustration
*1 Service Hole for Chain Tensioner *2 Oil Pump
*a Front View *b Back View