Home › Engine / Hybrid System › 1NZ-FE INTAKE / EXHAUST › INTAKE SYSTEM
NM19S0E _51 Engine / Hybrid System _051400 1NZ-FE INTAKE / EXHAUST _0247866 INTAKE SYSTEM UN GENERAL/CONTROL/DETAILS F

1NZ-FE INTAKE / EXHAUST  INTAKE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


CONSTRUCTION


a.

Air Cleaner

i.

A nonwoven, full-fabric type air cleaner filter element sub-assembly is used.

W105024E02
4.51,3.781 5.083,4.188 5.083,4.188 5.354,4.188 true 4.604,2.563 5.063,2.292 5.063,2.292 5.229,2.292 true 3.323,0.625 3.75,0.448 3.75,0.448 3.969,0.448 true 2.844,1.51 2.417,0.792 2.417,0.792 2.083,0.792 true 4,0.385 4.24,0.573 0.24,0.188 10 false *2 5.229,2.198 5.469,2.385 0.24,0.188 10 false *3 5.385,4.104 5.625,4.292 0.24,0.188 10 false *4 1.885,0.708 2.125,0.896 0.24,0.188 10 false *1

Text in Illustration
*1 Air Cleaner Cap Sub-assembly *2 Intake Mass Air Flow Meter Sub-assembly
*3 Air Cleaner Filter Element Sub-assembly *4 Air Cleaner Case



b.

Throttle with Motor Body Assembly

i.

The linkless-type throttle with motor body assembly is used and it realizes excellent throttle control.


ii.

A DC motor with excellent response and minimal power consumption is used for the throttle control motor. The ECM performs the duty ratio control of the direction and the amperage of the current that flows to the throttle control motor in order to regulate the opening angle of the throttle valve.

W103926E13
3.729,0.708 3.354,0.208 3.354,0.208 3.208,0.208 true 2.531,2.875 2.156,3.375 2.156,3.375 2.01,3.375 true 4.406,2.115 4.531,3 4.531,3 4.677,3 true 4.24,2.156 4.458,3.438 4.458,3.438 4.604,3.438 true 3.01,0.125 3.188,0.427 0.177,0.302 10 false *1 1.833,3.302 2.01,3.604 0.177,0.302 10 false *2 4.719,2.938 4.896,3.24 0.177,0.302 10 false *3 4.656,3.385 4.833,3.688 0.177,0.302 10 false *4

Text in Illustration
*1 Throttle Control Motor *2 Throttle Position Sensor
*3 Throttle Valve *4 Return Spring



c.

Intake Manifold

i.

The intake manifold has been made of plastic to reduce the weight and the amount of heat transferred from the cylinder head sub-assembly. As a result, it has become possible to reduce the intake temperature and improve the intake volumetric efficiency.


ii.

A mesh type gasket is used in order to reduce the intake noise.

W104617E04
1.958,1.563 2.104,1.552 2.104,1.552 2.51,2.219 true 2.5,1 2.646,1 2.646,1 3,1.625 true 2.354,0.917 2.625,1.125 0.271,0.208 10 false *1 1.792,1.469 2.063,1.677 0.271,0.208 10 false *2

Text in Illustration
*1 Intake Manifold *2 Mesh Type Gasket