Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2011.08–2017.01
NM19S0E _52 Drivetrain _051408 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0247875 AUTOMATIC TRANSAXLE SYSTEM UN GENERAL/CONTROL/DETAILS F

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the U340E automatic transaxle system are as follows:

Component Function
Forward Clutch (C1) Connects the input shaft and front planetary sun gear.
Direct Clutch (C2) Connects the intermediate shaft and rear planetary carrier.
Reverse Clutch (C3) Connects the intermediate shaft and rear planetary sun gear.
OD and 2nd Brake (B1) Locks the rear planetary sun gear.
2nd Brake (B2) Prevents the rear planetary sun gear from turning counterclockwise.
1st and Reverse Brake (B3) Locks the front planetary ring gear and rear planetary carrier.
No. 1 1-way Clutch (F1) Prevents the rear planetary sun gear from turning counterclockwise.
No. 2 1-way Clutch (F2) Prevents the front planetary ring gear and rear planetary carrier from turning counterclockwise.
Planetary Gears Change the route through which driving force is transmitted, in accordance with the operation of both clutch and brake, in order to increase or reduce the input and output speed.
Shift Solenoid Valve S1
·

Switches the 2-3 shift valve.

·

Controls the C2 clutch.


Shift Solenoid Valve S2
·

Switches the 1-2 and 3-4 shift valves.

·

Controls the C1clutch and 2 brakes (B1 and B2).


Shift Solenoid Valve ST
·

Switches the 3-4 shift timing valve.

·

Switches the No. 1 4-3 shift timing valve.


Shift Solenoid Valve SL Controls the lock-up clutch.
Shift Solenoid Valve SLT
·

Controls the line pressure.

·

Controls the secondary pressure.

·

Controls the accumulator backpressure.


ATF Temperature Sensor (Transmission Wire) Detects the ATF temperature.
Speed Sensor NT (Transmission Revolution Sensor) Detects the input speed of the transaxle.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Transmission Control Switch Detects the shift lever in 3 position.
Shift Lock Control ECU Sub-assembly Controls the shift lock system.
Stop Light Switch Assembly Detects the brake pedal depressed.
Combination Meter Assembly Detects the vehicle speed signal.
MIL Illuminates or blinks to inform the driver when the ECM detects a malfunction.
Shift Position Indicator Indicates the shift lever position.
ECM
·

Controls each shift solenoid valve and engine output in response to a signal from each sensor and switch.

·

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section.





SYSTEM CONTROL


a.

Automatic Transaxle Controls List

Control Outline
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to B1 brake and C1 clutch by actuating the shift solenoid valves (ST, SLT) in accordance with the ECM signals.
Clutch Pressure Control The shift solenoid valve SLT minutely controls the clutch pressure in accordance with the engine output and driving conditions.
Line Pressure Control Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transaxle.
Shift Control in Uphill/Downhill Traveling Controls to restrict the 4th upshift or to provide appropriate engine braking by using the ECM to determine whether the vehicle is traveling on uphill or downhill.
Shift Timing Control The ECM sends current to the shift solenoid valve S1 and/or S2 based on signals from each sensor and shifts the gear.
Lock-up Timing Control The ECM sends current to the shift solenoid valve SL based on the signals from each sensor and engages or disengages the lock-up clutch.
Engine Torque Control Temporarily retards the engine ignition timing to restrict the output torque, thus ensuring the shift feel during up or down shifting.
"N" to "D" Squat Control When the shift lever is shifted from the "N" to "D" position, the gear is temporarily shifted to the 3rd and then to the 1st to reduce vehicle squat.
Shift Lock System The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON, and the brake pedal is depressed.
Fail-safe Even if a malfunction is detected in the sensors or solenoids, the ECM effects fail-safe control to prevent the vehicle's drivability from being affected significantly.
Diagnosis When the ECM detects a malfunction, the ECM makes a diagnosis and memorizes the failed section.


b.

Clutch to Clutch Pressure Control

i.

This control is used for shifting from 3rd to 4th gear, and from 4th to 3rd gear. It actuates shift solenoid valves ST and SLT in accordance with the signals from the ECM, and guides this output pressure directly to the No. 1 4-3 shift timing valve and the 3-4 shift timing valve in order to regulate the line pressure that acts on the B1 brake (OD and 2nd brake) and C1 clutch (forward clutch).


ii.

As a result, compact B1 and C1 accumulators without a backpressure chamber have been realized.

X106284E12
4.573,0.771 4.781,0.323 4.781,0.323 4.958,0.323 true 3.896,1.115 4.031,1.115 4.031,1.115 4.354,1.729 true 1.771,3.031 1.927,3.031 1.927,3.031 2.5,2.125 true 1.896,0.479 3.917,0.719 2.021,0.24 10 false SHIFT SOLENOID VALVE SLT 2.438,2.948 4.365,3.25 1.927,0.302 10 false SHIFT SOLENOID VALVE ST 5.021,0.208 6.927,0.563 1.906,0.354 10 false ACCUMULATOR CONTROL VALVE 2.24,1.01 4,1.26 1.76,0.25 10 false 3-4 SHIFT TIMING VALVE 0.729,2.521 1.99,2.76 1.26,0.24 10 false 3-4 SHIFT VALVE 0.76,2.917 1.76,3.719 1,0.802 10 false No. 1 4-3 SHIFT TIMING VALVE 5.604,1.833 5.844,2.01 0.24,0.177 10 false C1 5.615,3.156 5.854,3.354 0.24,0.198 10 false B1



c.

Clutch Pressure Control

i.

The ECM monitors the signals from various types of sensor such as the speed sensor NT (transmission revolution sensor), allowing shift solenoid valve SLT to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics have been realized.

X106285E11
2.885,3.969 2.427,2.667 2.427,2.667 2.292,2.667 true 3.865,4.219 3.927,4.5 3.927,4.5 4.021,4.5 true 0.229,1.063 0.656,2.219 0.427,1.156 10 false Input Shaft Speed 1.302,2.219 1.74,2.417 0.438,0.198 10 false Time 2.906,6.052 3.344,6.25 0.438,0.198 10 false Time 1.167,5.479 2.521,5.76 1.354,0.281 10 false Output Shaft Torque 5.25,4.698 6.792,5.135 1.542,0.438 10 false Solenoid Drive Signal 5.052,3.719 5.896,4.521 0.844,0.802 10 false Clutch/Brake Pressure 0.188,2.604 2.229,3.625 2.042,1.021 10 false SPEED SENSOR NT (TRANSMISSION REVOLUTION SENSOR) 4.177,1.083 4.552,1.292 0.375,0.208 10 false ECM 5.135,0.927 6.979,1.208 1.844,0.281 10 false Signal form Various Sensors 5.135,1.323 6.979,1.604 1.844,0.281 10 false Engine Speed 5.135,1.719 6.979,2 1.844,0.281 10 false Engine Torque Information 5.125,2.073 6.396,2.313 1.271,0.24 10 false ATF Temperature 4.073,4.396 4.865,5.594 0.792,1.198 10 false SHIFT SOLENOID VALVE SLT 1.75,0.781 2.594,1.604 0.844,0.823 10 false Target rpm Change Ratio 0.802,1.74 2.635,1.958 1.833,0.219 10 false Practical rpm Change Ratio



d.

Line Pressure Control

i.

Through the use of the shift solenoid valve SLT, the line pressure is appropriately controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter assembly and the transaxle.


ii.

Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition and the ATF temperature, thus realizing smooth shift characteristics and regulating the workload in the oil pump.

X106363E07
0.51,0.208 1.479,0.531 0.969,0.323 10 false Line Pressure 1.771,0.833 2.625,1.729 0.854,0.896 10 false PRIMARY REGULATOR 3.167,3.167 4.333,4.021 1.167,0.854 10 false SHIFT SOLENOID VALVE SLT 4,0.375 4.906,1.427 0.906,1.052 10 false Shift Solenoid Valve Drive Signal 5.719,0.823 7.073,1.156 1.354,0.333 10 false Speed Sensor NT 5.76,1.323 7.115,1.656 1.354,0.333 10 false ATF Temperature 5.76,1.813 7.115,2.146 1.354,0.333 10 false Shift Position 5.76,2.271 6.646,2.948 0.885,0.677 10 false Throttle Valve Opening 5.76,3.031 7.115,3.365 1.354,0.333 10 false Intake Air Mass 5.76,3.469 7.115,3.802 1.354,0.333 10 false Engine Speed 5.74,4.021 6.708,4.76 0.969,0.74 10 false Engine Coolant Temperature 1.427,3.333 2.115,3.938 0.688,0.604 10 false Fluid Pressure 2.333,4.229 2.917,4.542 0.583,0.313 10 false Current 0.219,2.375 0.708,2.74 0.49,0.365 10 false PUMP 5.167,2.021 5.563,2.385 0.396,0.365 10 false ECM



e.

Shift Control in Uphill/Downhill Traveling

i.

This control helps minimize the gear shifting when the driver operates the accelerator pedal while driving on a winding uphill or downhill road in order to ensure a smooth drive.


ii.

When the ECM detects uphill travel, it prohibits upshifting to 4th after downshifting to 3rd.


iii.

If a signal indicating that the driver has operated the brake pedal is input while the ECM detects downhill travel, it downshifts from 4th to 3rd.

X106323E06
5.156,0.583 6.229,0.938 1.073,0.354 10 false Brake Operation 0.458,2.802 1.458,3.135 1,0.333 10 false Without Control 0.667,3.177 1.458,3.51 0.792,0.333 10 false With Control 1.552,2.906 1.802,3.177 0.25,0.271 10 false 4th 1.938,2.906 2.188,3.177 0.25,0.271 10 false 3rd 1.573,3.281 1.823,3.552 0.25,0.271 10 false 4th 2.385,3.292 2.635,3.563 0.25,0.271 10 false 3rd 5.771,3.271 6.021,3.542 0.25,0.271 10 false 4th 4.719,3.271 4.969,3.542 0.25,0.271 10 false 3rd 2.323,2.906 2.573,3.177 0.25,0.271 10 false 4th 3.729,2.896 3.979,3.167 0.25,0.271 10 false 4th 3.76,3.281 4.01,3.552 0.25,0.271 10 false 4th 2.885,2.906 3.135,3.177 0.25,0.271 10 false 3rd


iv.

The actual acceleration calculated from the speed sensor signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.

X104263E03
2.823,0.469 2.938,0.219 2.938,0.219 3.094,0.219 true 3.125,0.146 3.333,0.354 0.208,0.208 10 false *a

Text in Illustration (Uphill:)
*a Smaller - -
V100135

Reference Acceleration
V100136

Actual Acceleration

X104264E04
2.75,0.74 2.948,0.25 2.948,0.25 3.115,0.25 true 3.177,0.156 3.385,0.365 0.208,0.208 10 false *a

Text in Illustration (Downhill:)
*a Greater - -
V100135

Reference Acceleration
V100136

Actual Acceleration



f.

Shift Lock System

i.

The key interlock device prevents the key from being pulled out after the ignition switch is turned OFF, unless the shift lever is moved to the P position. Thus, the driver is urged to park the vehicle in the P position.


ii.

The shift lock mechanism prevents the shift lever from being shifted to a position other than the P position, unless the ignition switch is ON and the brake pedal is depressed. It prevents the vehicle from starting off suddenly.


iii.

The shift lock control ECU Sub-assembly uses the P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and ignition switch. Upon receiving these signals, the shift lock control ECU Sub-assembly turns on the key interlock solenoid and the shift lock solenoid in order to release the key interlock and shift lock.


iv.

A shift lock release button, which manually overrides the shift lock mechanism, is used.

X106305E09
0.458,0.573 1.875,1.198 1.417,0.625 10 false STOP LIGHT SWITCH ASSEMBLY 0.458,1.292 1.271,1.563 0.813,0.271 10 false IG1 RELAY 2.792,0.615 4.323,1.667 1.531,1.052 10 false SHIFT LOCK CONTROL ECU SUB-ASSEMBLY 4.688,0.865 6.667,1.083 1.979,0.219 10 false KEY INTERLOCK SOLENOID 4.781,1.406 6.49,1.615 1.708,0.208 10 false SHIFT LOCK SOLENOID 3.927,2.063 5.656,2.292 1.729,0.229 10 false P DETECTION SWITCH




CONSTRUCTION


a.

Torque Converter Assembly

i.

The torque converter assembly has appropriately designed fluid passages and impeller configuration, resulting in substantially enhanced torque ratio and transmission efficiency to ensure good starting, acceleration and fuel economy.


ii.

Furthermore, a hydraulically operated lock-up mechanism which cuts power transmission losses due to slippage at medium and high speeds is used.

X106290E05
2.448,0.448 2.563,0.448 2.563,0.448 3.198,0.927 true 2.448,1.333 2.552,1.333 2.552,1.333 3.552,1.667 true 2.438,3.208 2.563,3.208 2.563,3.208 3.406,2.552 true 3.656,0.958 4.438,0.427 4.438,0.427 4.542,0.427 true 3.938,3.01 4.51,3.396 4.51,3.396 4.635,3.396 true 2.271,0.344 2.469,0.542 0.198,0.198 10 false *1 4.583,0.323 4.781,0.521 0.198,0.198 10 false *4 4.708,3.313 4.906,3.51 0.198,0.198 10 false *5 2.271,1.229 2.469,1.427 0.198,0.198 10 false *2 2.25,3.104 2.448,3.302 0.198,0.198 10 false *3

Text in Illustration
*1 Pump Impeller *2 1-way Clutch
*3 Stator *4 Turbine Runner
*5 Lock-up Clutch - -



b.

Oil Pump

i.

The oil pump is combined with torque converter assembly, lubricates the planetary gear units and supplies operating pressure to the hydraulic control.

X106306E05
3.156,1.417 2.354,0.646 2.354,0.646 2.156,0.646 true 1.979,1.5 1.365,0.938 1.365,0.938 1.167,0.938 true 4.219,1.229 3.146,0.365 3.146,0.365 2.958,0.365 true 2.938,1.865 3.198,2.375 3.198,2.375 3.396,2.375 true 0.979,0.823 1.188,1.031 0.208,0.208 10 false *1 3.458,2.271 3.667,2.479 0.208,0.208 10 false *2 1.958,0.542 2.167,0.75 0.208,0.208 10 false *3 2.76,0.26 2.969,0.469 0.208,0.208 10 false *4

Text in Illustration
*1 Front Oil Pump Body *2 Front Oil Pump Driven Gear
*3 Front Oil Pump Drive Gear *4 Stator Shaft Assembly



c.

Planetary Gear Unit

i.

A CR-CR type planetary gear is used in the planetary gear unit, which is located on the input shaft. In this planetary gear unit, the front planetary carrier is joined to the rear ring gear, and the rear planetary carrier is joined to the front ring gear. As a result, the unit has been made significantly simpler and compact.


ii.

A centrifugal fluid pressure canceling mechanism is used in the C1 clutch, which is applied when downshifting from 4th.

X106291E06
1.25,1.719 1.375,1.719 1.375,1.719 2.625,2.115 true 1.479,1.344 1.583,1.344 1.583,1.344 2.125,1.74 true 1.76,0.979 1.865,0.979 1.865,0.979 2.198,1.531 true 2.01,0.646 2.135,0.646 2.135,0.646 2.375,1.5 true 2.552,1.615 2.74,0.844 2.74,0.844 2.833,0.844 true 2.917,1.531 3.229,0.708 3.229,0.708 3.354,0.708 true 3.271,1.688 3.792,0.51 3.792,0.51 3.917,0.51 true 3.479,1.656 3.854,0.896 3.854,0.896 3.958,0.896 true 1.427,3.115 1.542,3.115 1.542,3.115 2.385,2.417 true 2.302,2.625 1.927,3.448 1.927,3.448 1.823,3.448 true 2.896,2.26 2.51,3.5 2.51,3.5 2.427,3.5 true 3.25,3.625 3.125,3.906 3.125,3.906 2.99,3.906 true 4.573,2.156 5.083,1.458 5.083,1.458 5.188,1.458 true 2.115,5.385 1.865,4.927 1.865,4.927 1.76,4.927 true 3.719,5.427 3.948,4.927 3.948,4.927 4.094,4.927 true 4.615,5.552 4.792,5.177 4.792,5.177 4.927,5.177 true 5.438,6 5.604,6.167 5.604,6.167 5.719,6.167 true 4.896,6.927 5.115,7.146 5.115,7.146 5.229,7.146 true 1.552,0.865 1.802,1.063 0.25,0.198 10 false B1 1.802,0.552 2.052,0.75 0.25,0.198 10 false B2 3.406,0.583 3.656,0.781 0.25,0.198 10 false B3 3.979,0.417 4.229,0.615 0.25,0.198 10 false *1 1.063,1.615 1.313,1.813 0.25,0.198 10 false *3 1.594,4.844 1.844,5.042 0.25,0.198 10 false *3 2.792,4.688 3.042,4.885 0.25,0.198 9 false F2 3.229,4.719 3.479,4.917 0.25,0.198 10 false B3 2.813,3.813 3.063,4.01 0.25,0.198 10 false *5 4.979,5.042 5.229,5.24 0.25,0.198 10 false *1 5.25,7.052 5.5,7.25 0.25,0.198 10 false *5 2.25,3.396 2.5,3.594 0.25,0.198 10 false *4 4.135,4.802 4.385,5 0.25,0.198 10 false *4 1.615,3.323 1.865,3.521 0.25,0.198 10 false C3 1.406,5.49 1.656,5.688 0.25,0.198 10 false C2 1.396,6.26 1.646,6.458 0.25,0.198 10 false C3 5.156,5.396 5.406,5.594 0.25,0.198 10 false C1 1.646,6.802 1.896,7 0.25,0.198 10 false B1 2.719,6.823 2.969,7.021 0.25,0.198 10 false B2 2.729,6.375 2.979,6.573 0.25,0.198 9 false F1 4.031,0.76 4.281,0.958 0.25,0.198 10 false C1 1.26,1.24 1.51,1.438 0.25,0.198 10 false C2 5.271,1.354 5.521,1.552 0.25,0.198 10 false *2 5.76,6.052 6.01,6.25 0.25,0.198 10 false *2 2.885,0.74 3.135,0.938 0.25,0.198 10 false F2 1.24,3.01 1.49,3.208 0.25,0.198 10 false F1

Text in Illustration
*1 Counter Drive Gear *2 Input Shaft
*3 Rear Planetary Gear Assembly *4 Front Planetary Gear Assembly
*5 Counter Driven Gear - -


iii.

The functions of the clutches and brakes are as follows:

Component Function
C1 Forward Clutch Connects the input shaft and front planetary sun gear.
C2 Direct Clutch Connects the intermediate shaft and rear planetary carrier.
C3 Reverse Clutch Connects the intermediate shaft and rear planetary sun gear.
B1 OD and 2nd Brake Locks the rear planetary sun gear.
B2 2nd Brake Prevents the rear planetary sun gear from turning counterclockwise.
B3 1st and Reverse Brake Locks the front planetary ring gear and rear planetary carrier.
F1 No. 1 1-way Clutch Prevents the rear planetary sun gear from turning counterclockwise.
F2 No. 2 1-way Clutch Prevents the front planetary ring gear and rear planetary carrier from turning counterclockwise.
Planetary Gears These gears change the route through which driving force is transmitted, in accordance with the operation of both clutch and brake, in order to increase or reduce the input and output speed.



d.

Centrifugal Fluid Pressure Canceling Mechanism

i.

During shifting, in addition to the fluid pressure controlled by the valve body, the fluid pressure generated by centrifugal force (centrifugal fluid pressure) in chamber A also acts on the piston, and causes an increase in shifting shock generated by revolution differences between the input and output parts of the clutch by speeding the clutch engagement.


ii.

In order to improve the shifting characteristics for 4-3 and 3-4 shifting for which high responsiveness is required, a centrifugal fluid pressure canceling mechanism is applied.

X106292E05
4.396,0.479 4.479,0.479 4.479,0.479 4.729,0.979 true 5.271,1.01 5.583,0.698 5.583,0.698 5.656,0.698 true 5.198,1.281 5.615,1.563 5.615,1.563 5.708,1.563 true 5.135,1.688 5.396,2.125 5.396,2.125 5.479,2.125 true 4.229,0.375 4.469,0.573 0.24,0.198 10 false *1 5.677,0.615 5.917,0.813 0.24,0.198 10 false *2 5.781,1.458 6.021,1.656 0.24,0.198 10 false *3 5.542,2.01 5.781,2.208 0.24,0.198 10 false *4

Text in Illustration
*1 C1 Clutch *2 Chamber A
*3 Chamber B *4 Piston


iii.

The canceling fluid pressure canceling mechanism is a chamber (chamber B) located opposite to chamber A. By filling chamber B with shaft lubrication fluid, an equal amount of centrifugal fluid pressure is generated there and works against the centrifugal fluid pressure in chamber A.

U135261E04
3.823,0.323 3.99,0.323 3.99,0.323 3.99,0.656 false 3.656,1.51 3.479,1.51 3.479,1.51 3.479,1.177 true 2.729,0.365 3.01,0.365 3.01,0.365 3.01,1.24 false 1.167,1.323 1.625,1.323 false 1.729,2.667 2.229,2.667 2.229,2.667 2.229,2.385 false 4.688,3.531 6.479,4.271 1.792,0.74 10 false Target fluid pressure (original clutch pressure) 2.469,3.542 3.99,4.344 1.521,0.802 10 false Centrifugal fluid pressure generated in chamber B 5.083,1.729 6.729,2.646 1.646,0.917 10 false : Centrifugal fluid pressure generated in to chamber B 5.094,1.083 6.74,1.76 1.646,0.677 10 false : Centrifugal fluid pressure generated in to chamber A 5.104,0.448 6.469,1.063 1.365,0.615 10 false : Target fluid pressure 3.385,0.188 4.271,0.594 0.885,0.406 10 false Clutch 3.719,1.406 4.406,1.833 0.688,0.427 10 false Piston 0.948,0.25 2.688,1.021 1.74,0.771 10 false Chamber B (Canceling Fluid Pressure Chamber) 0.323,1.208 1.125,2.531 0.802,1.323 10 false Chamber A (Piston Fluid Pressure Chamber) 0.563,2.542 1.688,3.208 1.125,0.667 10 false Fluid Pressure Applied to Piston 2.802,2.688 3.823,3.094 1.021,0.406 10 false Shaft Side 0.646,3.563 2.01,4.302 1.365,0.74 10 false Fluid pressure applied to piston



e.

Transmission Valve Body Assembly

i.

The valve body consists of the upper and lower valve bodies and 5 shift solenoid valves.

X106293E03
1.698,0.177 1.823,0.177 1.823,0.177 2.094,0.302 true 1.302,1.135 1.448,1.135 1.448,1.135 1.854,1.292 true 1.323,2.313 1.427,2.313 1.427,2.313 1.688,2.094 true 2.167,2.531 2.26,2.531 2.26,2.531 2.552,2.344 true 4,2.49 4.115,2.49 4.115,2.49 4.396,2.365 true 5.344,2.021 5.698,1.823 5.698,1.823 5.792,1.823 true 4.688,0.875 5.094,0.573 5.094,0.573 5.198,0.573 true 1.521,0.083 1.729,0.292 0.208,0.208 10 false *1 1.125,1.031 1.333,1.24 0.208,0.208 10 false *6 1.135,2.208 1.344,2.417 0.208,0.208 10 false *2 1.979,2.417 2.188,2.625 0.208,0.208 10 false *3 3.833,2.375 4.042,2.583 0.208,0.208 10 false *4 5.875,1.708 6.083,1.917 0.208,0.208 10 false *5 5.271,0.469 5.479,0.677 0.208,0.208 10 false *7

Text in Illustration
*1 Shift Solenoid Valve SL *2 Shift Solenoid Valve S2
*3 Shift Solenoid Valve S1 *4 Shift Solenoid Valve ST
*5 Shift Solenoid Valve SLT *6 Lower Valve Body
*7 Upper Valve Body - -

X106294E06
2.927,1.531 2.417,0.375 2.417,0.375 2.302,0.375 true 3.271,1.521 3.531,0.292 3.531,0.292 3.677,0.292 true 3.854,1.479 4.302,0.365 4.302,0.365 4.448,0.365 true 4.375,1.583 5.344,0.344 5.344,0.344 5.469,0.344 true 2.448,2.667 1.771,3.49 1.771,3.49 1.646,3.49 true 3.229,2.49 2.688,3.5 2.688,3.5 2.583,3.5 true 4.365,2.552 3.917,3.521 3.917,3.521 3.76,3.521 true 5.125,2.604 5.354,3.385 5.354,3.385 5.521,3.385 true 1.906,2.271 1.229,3.094 1.229,3.094 1.115,3.094 true 1.479,3.375 1.698,3.552 0.219,0.177 10 false *2 2.385,3.406 2.604,3.583 0.219,0.177 10 false *5 3.583,3.427 3.802,3.604 0.219,0.177 10 false *8 5.573,3.302 5.792,3.479 0.219,0.177 10 false *9 2.146,0.26 2.365,0.438 0.219,0.177 10 false *3 5.531,0.25 5.75,0.427 0.219,0.177 10 false *7 3.74,0.156 3.958,0.333 0.219,0.177 10 false *4 4.51,0.25 4.729,0.427 0.219,0.177 10 false *6 0.969,2.99 1.188,3.167 0.219,0.177 10 false *1

Text in Illustration (Upper Valve Body:)
*1 Lock-up Relay Valve *2 Secondary Regulator Valve
*3 3-4 Shift Timing Valve *4 Low Coast Modulator Valve
*5 No. 1 4-3 Shift Timing Valve *6 2-3 Shift Valve
*7 Coast Relay Valve *8 Solenoid Relay Valve
*9 Reverse Control Valve - -

X106295E05
2.74,1.771 2.115,0.469 2.115,0.469 2.031,0.469 true 3.531,2.354 4.083,0.469 4.083,0.469 4.219,0.469 true 3.948,2.594 4.667,1.042 4.667,1.042 4.813,1.042 true 4.771,2.427 5.635,1.583 5.635,1.583 5.781,1.583 true 3.292,2.802 3.896,4.354 3.896,4.354 4,4.354 true 2.917,2.979 2.177,4.344 2.177,4.344 2.063,4.344 true 1.865,0.344 2.052,0.531 0.188,0.188 10 false *3 1.885,4.229 2.073,4.417 0.188,0.188 10 false *1 4.063,4.229 4.25,4.417 0.188,0.188 10 false *2 4.292,0.354 4.479,0.542 0.188,0.188 10 false *4 4.896,0.906 5.083,1.094 0.188,0.188 10 false *5 5.844,1.49 6.031,1.677 0.188,0.188 10 false *6

Text in Illustration (Lower Valve Body:)
*1 No. 2 4-3 Shift Timing Valve *2 3-4 Shift Valve
*3 Primary Regulator Valve *4 1-2 Shift Valve
*5 Accumulator Control Valve *6 Pressure Relief Valve



f.

Shift Solenoid Valve SLT

i.

In order to supply hydraulic pressure proportional to the current that flows to the solenoid coil, shift solenoid valve SLT is provided.


ii.

The valve linearly controls the line pressure, secondary pressure and accumulator backpressure based on the signals from the ECM.

X105785E06
1.083,0.615 1.188,0.615 1.188,0.615 1.281,1.281 true 1.281,2.156 1.385,2.156 1.385,2.156 1.469,1.531 true 0.292,0.51 1.115,0.75 0.823,0.24 10 false Spool Valve 0.802,2.052 1.375,2.323 0.573,0.271 10 false Sleeve 4.021,0.521 4.75,1 0.729,0.479 10 false Hydraulic Pressure 6.021,1.99 6.667,2.24 0.646,0.25 10 false Current

Function of Shift Solenoid Valve SLT
Shift Solenoid Valve Function
SLT
·

Line pressure control

·

Secondary pressure control

·

Accumulator backpressure control





g.

Shift Solenoid Valve SL

i.

This shift solenoid valve use a 3-way solenoid valve.

X106364E02
2.208,1.479 2.427,1.667 0.219,0.188 10 false *a 5.344,1.49 5.583,1.708 0.24,0.219 10 false *b

Text in Illustration
*a Off Condition *b On Condition
V100135

Control Pressure
V100136

Drain
V100137

Line Pressure
V100138

Cylinder Ball Moving Direction

Function of Shift Solenoid Valve SL
Shift Solenoid Valve Function
SL Lock-up clutch control



h.

Shift Solenoid Valve S1 and S2

i.

These shift solenoid valves use a 3-way solenoid valve.

X105787E05
1.99,1.469 2.229,1.677 0.24,0.208 10 false *a 5.365,1.458 5.604,1.667 0.24,0.208 10 false *b

Text in Illustration
*a Off Condition *b On Condition
V100135

Control Pressure
V100136

Drain
V100137

Line Pressure
V100138

Cylinder Ball Moving Direction

Function of Shift Solenoid Valve S1 and S2
Shift Solenoid Valve Function
S1
·

2-3 shift valve switching

·

C2 clutch control


S2
·

1-2 and 3-4 shift valves switching

·

C1 clutch and 2-brake (B1 and B2) control





i.

Shift Solenoid Valves ST

i.

This shift solenoid valve use a 3-way solenoid valve.

X105788E02
2.083,1.51 2.302,1.708 0.219,0.198 10 false *a 5.375,1.51 5.594,1.708 0.219,0.198 10 false *b

Text in Illustration
*a Off Condition *b On Condition
V100135

Control Pressure
V100136

Drain
V100137

Line Pressure
V100138

Cylinder Ball Moving Direction

Function of Shift Solenoid Valve ST
Shift Solenoid Valve Function
ST
·

3-4 shift timing valves switching

·

No. 1 4-3 shift valves switching





j.

ATF Temperature Sensor (Transmission Wire)

i.

The ATF temperature sensor (transmission wire) is installed in the lower valve body for direct detection of the fluid temperature.


ii.

The ATF temperature sensor (transmission wire) is used for the correction of clutch and brake pressures to give smooth shift quality every time.

X106296E05
1.74,0.677 1.896,0.677 1.896,0.677 2.021,1 true 4.01,2.281 4.146,2.281 4.146,2.281 4.354,2.115 true 1.552,0.552 1.823,0.792 0.271,0.24 10 false *1 3.833,2.156 4.125,2.406 0.292,0.25 10 false *2

Text in Illustration
*1 Lower Valve Body *2 ATF Temperature Sensor (Transmission Wire)



k.

Speed Sensor NT (Transmission Revolution Sensor)

i.

The speed sensor NT (transmission revolution sensor) detects the input speed of the transaxle. The forward clutch (C1) drum is used as the timing rotor for this sensor. Thus, the ECM can detect shift timing of the gears and appropriately control the engine torque and hydraulic pressure in response to the various conditions.

X106347E05
2,0.99 2.698,0.302 2.698,0.302 2.885,0.302 true 2.958,0.208 3.167,0.417 0.208,0.208 10 false *1

Text in Illustration
*1 Speed Sensor NT (Transmission Revolution Sensor) - -



l.

Shift Control Mechanism

i.

A gate type shift lever that uses a transmission control cable is used.


ii.

The shift control mechanism consists of a shift lock control unit assembly and a transmission control cable assembly.

X106345E03
1.771,1.927 1.917,1.927 1.917,1.927 2.177,2.427 true 3.677,1.354 3.906,1 3.906,1 4.042,1 true 1.604,1.813 1.896,2.073 0.292,0.26 10 false *1 4.083,0.875 4.375,1.135 0.292,0.26 10 false *2 4.594,2.333 4.885,2.594 0.292,0.26 10 false *a

Text in Illustration
*1 Transmission Control Cable Assembly *2 Shift Lock Control Unit Assembly
*a Shift Pattern - -



m.

Park/Neutral Position Switch Assembly and Transmission Control Switch

i.

The park/neutral position switch assembly sends the P, R, N, D, 2 and L position signals to the ECM.


ii.

The transmission control switch sends the 3 position signal to the ECM.


iii.

The ECM controls the automatic transaxle system in accordance with the shift lever position signals.


iv.

The ECM transmits signals to the combination meter assembly for the shift position indicator (P, R, N, D, 2, 3 and L) in response to the signals received from the switches.

X105779E07
1.188,2.688 3.76,3.188 2.573,0.5 10 false PARK/NEUTRAL POSITION SWITCH ASSEMBLY 5,4.74 6.281,5.74 1.281,1 10 false COMBINATION METER ASSEMBLY 5.073,5.833 6.281,6.479 1.208,0.646 10 false SHIFT POSITION INDICATOR 0.656,0.74 1.552,0.938 0.896,0.198 10 false to ST RELAY 0.563,1.583 1.604,1.813 1.042,0.229 10 false from IG RELAY 1.719,0.563 1.885,0.76 0.167,0.198 10 false L 2.865,0.604 3.115,0.802 0.25,0.198 10 false B 2.854,1 3.104,1.198 0.25,0.198 10 false PL 2.865,1.229 3.115,1.427 0.25,0.198 10 false RL 2.865,1.458 3.115,1.656 0.25,0.198 10 false NL 2.875,1.698 3.125,1.896 0.25,0.198 10 false DL 2.875,1.948 3.125,2.146 0.25,0.198 10 false 2L 2.844,3.469 3.385,3.667 0.542,0.198 10 false NSSD 4.75,3.729 4.969,3.927 0.219,0.198 10 false 3 2.865,3.781 3.229,3.979 0.365,0.198 10 false AT3 4.646,0.99 4.896,1.188 0.25,0.198 10 false P 4.573,0.615 4.948,0.813 0.375,0.198 10 false STA 4.646,1.25 4.896,1.448 0.25,0.198 10 false R 4.646,1.49 4.896,1.688 0.25,0.198 10 false N 4.656,1.719 4.906,1.917 0.25,0.198 10 false D 4.667,1.958 4.917,2.156 0.25,0.198 10 false 2 2.885,2.198 3.135,2.396 0.25,0.198 10 false LL 4.688,2.208 4.938,2.406 0.25,0.198 10 false L 1.635,1.406 1.917,1.604 0.281,0.198 10 false RB 1.198,4.313 3.656,4.51 2.458,0.198 10 false TRANSMISSION CONTROL SWITCH 5.479,2.031 5.875,2.229 0.396,0.198 10 false ECM 5.781,4.313 6.813,4.625 1.031,0.313 10 false CAN (V Bus)



n.

Automatic Transmission Fluid (ATF) WS

i.

TOYOTA genuine ATF WS is used to reduce the resistance of the ATF and ensure fuel economy by reducing its viscosity in the practical operation range. At the high-temperatures, the viscosity is the same as that of TOYOTA genuine ATF Type T-IV, which ensures the durability of the automatic transmission.

X100046E19
1.542,1.198 1.708,0.771 1.708,0.771 1.958,0.771 true 0.865,0.958 1.167,1.333 0.302,0.375 10 false High 3.229,2.24 3.531,2.615 0.302,0.375 10 false High 4.156,2.167 5.094,2.542 0.938,0.375 10 false Temperature 2.021,0.635 3.198,1.01 1.177,0.375 10 false Reduced Viscosity 0.677,0.458 1.25,0.833 0.573,0.375 10 false Viscosity 4.563,0.094 6.76,0.469 2.198,0.375 10 false : TOYOTA Genuine ATF Type T-IV 4.563,0.479 6.698,0.854 2.135,0.375 10 false : TOYOTA Genuine ATF WS




OPERATION


a.

Transmission Power Flow

Shift Lever Position Gear Solenoid Valve Clutch Brake 1-way Clutch
S1 S2 C1 C2 C3 B1 B2 B3 F1 F2
P Park On On - - - - - - - -
R Reverse On On - - ○ - - ○ - -
N Neutral On On - - - - - - - -
D 1st On On ○ - - - - - - ○
2nd On Off ○ - - - ○ - ○ -
3rd Off Off ○ ○ - - ○ - - -
4th Off On - ○ - ○ ○ - - -
3 1st On On ○ - - - - - - ○
2nd On Off ○ - - - ○ - ○ -
3rd Off Off ○ ○ - - ○ - - -
2 1st On On ○ - - - - - - ○
2nd On Off ○ - - ○ ○ - ○ -
L 1st On On ○ - - - - ○ - ○

HINT:

○: Operation

-: Not operation


X106298E08
3.125,0.698 3.344,0.896 0.219,0.198 10 false F2 3.573,0.708 3.792,0.906 0.219,0.198 10 false B3 1.698,1.521 1.917,1.719 0.219,0.198 10 false C2 5.594,1.417 5.813,1.615 0.219,0.198 10 false C1 0.177,0.219 2.385,0.448 2.208,0.229 12 false 1st Gear (D, 3 or 2 Position) : 6.5,1.927 6.938,2.146 0.438,0.219 10 false Input 0.719,3.469 1.521,3.698 0.802,0.229 10 false : Operates 1.688,2.323 1.906,2.521 0.219,0.198 10 false C3 1.958,2.885 2.177,3.083 0.219,0.198 10 false B1 3.063,2.875 3.281,3.073 0.219,0.198 10 false B2 3.063,2.438 3.281,2.635 0.219,0.198 10 false F1

X106299E07
3.083,0.625 3.302,0.823 0.219,0.198 10 false F2 3.552,0.646 3.771,0.844 0.219,0.198 10 false B3 1.604,1.479 1.823,1.677 0.219,0.198 10 false C2 5.646,1.385 5.865,1.583 0.219,0.198 10 false C1 0.156,0.219 2.365,0.448 2.208,0.229 12 false 2nd Gear (D or 3 Position) : 6.646,1.906 7.083,2.125 0.438,0.219 10 false Input 0.677,3.365 1.479,3.594 0.802,0.229 10 false : Operates 1.615,2.344 1.833,2.542 0.219,0.198 10 false C3 1.854,2.906 2.073,3.104 0.219,0.198 10 false B1 3.031,2.917 3.25,3.115 0.219,0.198 10 false B2 3.042,2.417 3.26,2.615 0.219,0.198 10 false F1

X106300E06
3.052,0.625 3.271,0.823 0.219,0.198 10 false F2 3.542,0.656 3.76,0.854 0.219,0.198 10 false B3 1.594,1.5 1.813,1.698 0.219,0.198 10 false C2 5.594,1.375 5.813,1.573 0.219,0.198 10 false C1 0.125,0.052 2.333,0.281 2.208,0.229 12 false 3rd Gear (D or 3 Position) : 6.531,1.906 6.969,2.125 0.438,0.219 10 false Input 0.677,3.365 1.479,3.594 0.802,0.229 10 false : Operates 1.604,2.323 1.823,2.521 0.219,0.198 10 false C3 1.865,2.875 2.083,3.073 0.219,0.198 10 false B1 3.01,2.896 3.229,3.094 0.219,0.198 10 false B2 3.01,2.417 3.229,2.615 0.219,0.198 10 false F1

X106301E06
3.021,0.604 3.24,0.802 0.219,0.198 10 false F2 3.5,0.635 3.719,0.833 0.219,0.198 10 false B3 1.542,1.469 1.76,1.667 0.219,0.198 10 false C2 5.604,1.396 5.823,1.594 0.219,0.198 10 false C1 0.083,0.188 1.823,0.458 1.74,0.271 12 false 4th Gear (D Position) : 6.49,1.906 6.927,2.125 0.438,0.219 10 false Input 0.625,3.365 1.427,3.594 0.802,0.229 10 false : Operates 1.531,2.333 1.75,2.531 0.219,0.198 10 false C3 1.802,2.896 2.021,3.094 0.219,0.198 10 false B1 2.969,2.906 3.188,3.104 0.219,0.198 10 false B2 2.958,2.427 3.177,2.625 0.219,0.198 10 false F1

X106302E06
3.042,0.573 3.26,0.771 0.219,0.198 10 false F2 3.531,0.604 3.75,0.802 0.219,0.198 10 false B3 1.563,1.469 1.781,1.667 0.219,0.198 10 false C2 5.635,1.375 5.854,1.573 0.219,0.198 10 false C1 0.104,0.229 1.844,0.5 1.74,0.271 12 false 2nd Gear (2 Position) : 6.563,1.885 7,2.104 0.438,0.219 10 false Input 0.646,3.385 1.448,3.615 0.802,0.229 10 false : Operates 1.552,2.323 1.771,2.521 0.219,0.198 10 false C3 1.813,2.906 2.031,3.104 0.219,0.198 10 false B1 3,2.906 3.219,3.104 0.219,0.198 10 false B2 2.979,2.417 3.198,2.615 0.219,0.198 10 false F1

X106303E06
3.063,0.635 3.281,0.833 0.219,0.198 10 false F2 3.51,0.667 3.729,0.865 0.219,0.198 10 false B3 1.646,1.469 1.865,1.667 0.219,0.198 10 false C2 5.5,1.396 5.719,1.594 0.219,0.198 10 false C1 0.115,0.156 1.854,0.427 1.74,0.271 12 false 1st Gear (L Position) : 6.417,1.865 6.854,2.083 0.438,0.219 10 false Input 0.656,3.417 1.458,3.646 0.802,0.229 10 false : Operates 1.646,2.302 1.865,2.5 0.219,0.198 10 false C3 1.906,2.823 2.125,3.021 0.219,0.198 10 false B1 3,2.813 3.219,3.01 0.219,0.198 10 false B2 3,2.385 3.219,2.583 0.219,0.198 10 false F1

X106304E06
3.042,0.646 3.26,0.844 0.219,0.198 10 false F2 3.51,0.646 3.729,0.844 0.219,0.198 10 false B3 1.625,1.458 1.844,1.656 0.219,0.198 10 false C2 5.542,1.354 5.76,1.552 0.219,0.198 10 false C1 0.104,0.188 2.344,0.458 2.24,0.271 12 false Reverse Gear (R Position) : 6.417,1.865 6.854,2.083 0.438,0.219 10 false Input 0.656,3.417 1.458,3.646 0.802,0.229 10 false : Operates 1.625,2.26 1.844,2.458 0.219,0.198 10 false C3 1.854,2.823 2.073,3.021 0.219,0.198 10 false B1 3,2.823 3.219,3.021 0.219,0.198 10 false B2 3,2.365 3.219,2.563 0.219,0.198 10 false F1



FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or shift solenoid valve.

Malfunction Part Function
Vehicle Speed Signal During a vehicle speed signal malfunction, the 4th upshift is prohibited.
Speed Sensor NT (Transmission Revolution Sensor) During a speed sensor NT (transmission revolution sensor) signal malfunction, the 4th upshift is prohibited.
ATF Temperature Sensor (Transmission Wire) During a ATF temperature sensor (transmission wire) malfunction, the 4th upshift is prohibited.
Shift Solenoid Valve SLT or ST During a shift solenoid valve SLT or ST malfunction, the 4th upshift is prohibited.
E.F.I. Engine Coolant Temperature Sensor, Knock Control Sensor or Throttle Position Sensor During an E.F.I. engine coolant temperature sensor, knock control sensor or throttle position sensor malfunction, the 4th upshift is prohibited.
Shift Solenoid Valve S1 or S2 During a malfunction in the shift solenoid valve S1 or S2, the current to the faulty shift solenoid valve is cut off and control is effected by operating the normal shift solenoid valves. Shift control is effected as described in the table below, depending on the failed shift solenoid valve.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the ECM are output to the intelligent tester via the ECM and the DLC3.


c.

For details, refer to the Repair Manual.