Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2011.08–2014.07
NM19S0E _54 Brake _051417 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0247884 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

ABS with EBD

Component Function
Brake Actuator Assembly Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends brake control signals to the brake actuator.
Solenoid Valve Changes the fluid path based on the signals from the skid control ECU during the operation of the ABS with EBD, in order to control the fluid pressure that is applied to the wheel cylinders.
Pump Motor Drives the pumps inside the brake actuator.
Solenoid Relay Supplies power to the solenoid valves.
Motor Relay Supplies power to the motor.
Front Speed Sensor RH Detect the wheel speed of each of the 4 wheels.
Front Speed Sensor LH
Rear Speed Sensor RH (Skid Control Sensor Wire RH)
Rear Speed Sensor LH (Skid Control Sensor Wire LH)
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Assembly Detects when the parking brake lever is pulled up.
Brake Fluid Level Warning Switch Detects the brake fluid level.
Main Body ECU (Multiplex Network Body ECU) Transmits the parking brake switch signal to the skid control ECU.
Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Brake Warning Light
·

Lights up together with ABS warning light to alert the driver when the skid control ECU detects the malfunction not only in the ABS but also in the EBD.

·

Lights up to alert the driver when the brake fluid level is low.

·

Lights up to inform the driver when the parking brake lever is pulled up or the parking brake pedal is depressed.




b.

ABS with EBD, Brake Assist, TRC and VSC

Component Function
Brake Actuator Assembly Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends brake control signals to the brake actuator.
Solenoid Valve Changes the fluid path based on the signals from the skid control ECU during the operation of the ABS with EBD, Brake Assist, TRC and VSC, in order to control the fluid pressure that is applied to the wheel cylinders.
Master Cylinder Cut Solenoid Valve
Pump Motor Drives the pumps inside the brake actuator.
Solenoid Relay Supplies power to the solenoid valves.
Motor Relay Supplies power to the motor.
Motor Failsafe Relay Cuts the power to the motor when the motor relay malfunctions.
Master Cylinder Pressure Sensor Assembled in the brake actuator, detects the master cylinder pressure.
Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Airbag Sensor Assembly*1 Yaw Rate and Deceleration Sensor Detects the yaw rate and the longitudinal and lateral acceleration and deceleration of the vehicle body.
Yaw Rate and Deceleration Sensor (Yaw Rate Sensor)*2 Detects the yaw rate and the longitudinal and lateral acceleration and deceleration of the vehicle body.
Front Speed Sensor RH Detect the wheel speed of each of the 4 wheels.
Front Speed Sensor LH
Rear Speed Sensor RH (Skid Control Sensor Wire RH)
Rear Speed Sensor LH (Skid Control Sensor Wire LH)
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Assembly Detects when the parking brake lever is pulled up.
Brake Fluid Level Warning Switch Detects the brake fluid level.
VSC OFF Switch Enables the driver to select the "Normal Mode", "TRC-OFF Mode" or "VSC-OFF Mode".
Main Body ECU (Multiplex Network Body ECU) Transmits the parking brake switch signal to the skid control ECU.
ECM
·

Sends the throttle position signal, accelerator pedal position signal engine speed signal to the skid control ECU.

·

Based on the signals receives from the skid control ECU, controls the engine output.


Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Brake Warning Light
·

Lights up together with ABS warning light to alert the driver when the skid control ECU detects the malfunction not only in the ABS but also in the EBD.

·

Lights up to alert the driver when the brake fluid level is low.

·

Lights up to inform the driver when the parking brake lever is pulled up.


Slip Indicator Light
·

Lights up to alert the driver if the TRC or VSC system malfunctions.

·

Blinks to inform the driver when the TRC or VSC operates.


TRC OFF Indicator Light Lights up to inform the driver of "TRC-OFF mode" or "VSC-OFF mode" being selected.
VSC OFF Indicator Light Lights up to inform the driver of "VSC-OFF mode" being selected.

*1: w/ Built-in Type Yaw Rate Sensor

*2: w/ Separate Type Yaw Rate Sensor




SYSTEM CONTROL


a.

Control List

i.

The brake control system (ABS with EBD) have the following controls:

Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior.
Brake Assist The primary purpose of the Brake Assist is to provide an auxiliary brake force to assist the driver who cannot generate a large brake force during emergency braking, thus helping draw the vehicle's brake performance.


ii.

The brake control system (ABS with EBD, Brake Assist, TRC and VSC) have the following controls:

Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior.
Brake Assist The primary purpose of the Brake Assist is to provide an auxiliary brake force to assist the driver who cannot generate a large brake force during emergency braking, thus helping draw the vehicle's brake performance.
Traction Control (TRC) The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Vehicle Stability Control (VSC) The VSC helps prevent the vehicle from slipping sideway as a result of strong front wheel skid or strong rear wheel skid during cornering.
Engine Output Control during TRC or VSC Operation Transmits an engine output control signal from the skid control ECU to the ECM to limit the engine output while the TRC or VSC is being activated.



b.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X106018E01
5.057,0.784 5.309,0.960 0.252,0.175 10 *A 5.057,1.646 5.309,1.822 0.252,0.175 10 *B 3.712,2.464 3.964,2.639 0.252,0.175 10 *a

Text in Illustration
*A With ABS *B Without ABS
*a Brake Operation - -



c.

Electronic Brake Force Distribution (EBD)

i.

The distribution of the brake force, which was performed mechanically in the past, is now performed under electrical control of the skid control ECU, which controls the braking force in accordance with the vehicle's driving conditions.


ii.

If the brakes are applied while the vehicle is moving straight forward, the transfer of the load reduces the weight that is applied to the rear wheels. The skid control ECU determines this condition by way of the signals from the speed sensor, and the brake actuator regulates the distribution of the brake force of the rear wheels to optimally control. For example, the amount of the brake force that is applied to the rear wheels during braking varies depending on whether the vehicle is carrying load or not. The amount of the brake force that is applied to the rear wheels also varies in accordance with the extent of the deceleration. Thus, the distribution of the brake force to the rear is optimally controlled in order to effectively utilize the braking force of the rear wheels under these conditions.

X106019E04
1.698,2.625 1.865,1.771 1.865,1.771 2.063,1.771 true 4.823,2.323 4.99,1.469 4.99,1.469 5.188,1.469 true 1.958,2.552 2.083,2.646 2.083,2.646 2.281,2.646 true 5.073,2.458 5.198,2.552 5.198,2.552 5.396,2.552 true 0.635,2.229 1.323,3.021 0.688,0.792 10 false Rear Bake Force 3.635,2.198 4.313,2.896 0.677,0.698 10 false Rear Bake Force 1.635,3.031 3.031,3.354 1.396,0.323 10 false Front Bake Force 1.698,3.458 3.74,3.802 2.042,0.344 10 false Without Load in Rear 4.646,3.458 6.688,3.802 2.042,0.344 10 false With Load in Rear 4.604,3.031 6,3.479 1.396,0.448 10 false Front Bake Force 2.115,1.688 3.208,2.333 1.094,0.646 10 false Ideal Brake Force Distribution 2.344,2.542 3.396,2.865 1.052,0.323 10 false EBD Control 5.24,1.365 6.344,2.031 1.104,0.667 10 false Ideal Brake Force Distribution 5.427,2.479 6.698,2.927 1.271,0.448 10 false EBD Control


iii.

When the brakes are applied while the vehicle is cornering, the load that is applied to the inner wheel decreases as the load to the outer wheel increases. The skid control ECU determines this condition by way of the signals from the speed sensor, and the brake actuator regulates the brake force in order to optimally control the distribution of the brake force to the inner wheel and outer wheel.

X106020E03
4.156,0.479 4.469,0.156 4.469,0.156 4.615,0.156 true 4.656,0.073 4.906,0.25 0.25,0.177 10 false *a

Text in Illustration
*a Control Moment - -
V100135

Brake Force - -



d.

Brake Assist

i.

The Brake Assist in combination with the ABS helps ensure the vehicle's brake performance.


ii.

The Brake Assist interprets a quick push of the brake pedal as emergency braking and supplements the brake force applied if the driver has not depressed hard enough the brake pedal. In emergencies, drivers, especially inexperienced ones, often panic and do not apply sufficient pressure on the brake pedal.


iii.

A key feature of Brake Assist is that the timing and the degree of braking assistance are designed to help ensure that the driver dose not discern anything unusual about the braking operation. When the driver intentionally eases up on the brake pedal, the system reduces the amount of assistance it provides.


iv.

The mechanical type Brake Assist uses the brake assist mechanism in the brake booster to mechanically activate the brake booster function in order to increase the brake force.


v.

In the electrical type brake assist, based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the speed and the amount of the brake pedal application and then determines the intention of the driver to make an emergency braking. If the skid control ECU determines that the driver intends emergency braking, this function activates the brake actuator to increase the brake fluid pressure, which increases the braking force.

X106021E02
4.219,2.615 4.063,2.313 4.063,2.313 3.938,2.313 true 0.146,2.615 0.396,1.25 0.396,1.25 0.594,1.25 true 3.177,2.208 3.896,4.021 0.719,1.813 10 false The fluid pressure is increased by the brake actuator 3.448,1.042 4.625,2.188 1.177,1.146 10 false Master Cylinder Pressure Sensor Signal 0.094,0.135 6.875,0.521 6.781,0.385 12 false In case that the driver's depressing force is small when emergency braking is applied: 5.219,1.063 6.198,2.177 0.979,1.115 10 false Fluid Pressure Control Signal 4.146,3.781 6.625,4.438 2.479,0.656 10 false With Brake Assist (Electric Type) 0.302,3.771 2.823,4.323 2.521,0.552 10 false With Brake Assist (Mechanical Type) 4.542,4.74 6,5.052 1.458,0.313 10 false With Brake Assist 3.323,5.51 3.99,6.167 0.667,0.656 10 false Braking Force 0.49,7.146 6.979,7.844 6.49,0.698 10 false There is no difference of the maximum brake performance between the vehicles with and without Brake Assist. 4.573,5.521 6.031,5.833 1.458,0.313 10 false Without Brake Assist 5.344,6.708 5.917,7.021 0.573,0.313 10 false Time 4.271,0.625 5.802,0.938 1.531,0.313 10 false SKID CONTROL ECU 0.427,6.177 1.958,6.49 1.531,0.313 10 false Without Brake Assist 0.625,1.135 2.583,1.948 1.958,0.813 10 false The fluid pressure is increased by the brake booster



e.

Traction Control (TRC)

i.

If the driver depresses the accelerator pedal aggressively when initially acceleration or when accelerating on a slippery surface, the drive wheels could slip due to the excessive amount of torque that is generated. By applying hydraulic brake control to the drive wheels and regulating the throttle to control the engine output, the TRC helps minimize the slippage of the drive wheels, thus generating the drive force that is appropriate for the road surface conditions.


ii.

For example, a comparison may be made between two vehicles, one with the TRC and the other without. If the driver of each vehicle operates the accelerator pedal in a rough manner while driving over a surface with different surface friction characteristics, the drive wheel on the slippery surface could slip as illustrated. As a result, the vehicle could become unstable. However, when the vehicle is equipped with the TRC, the skid control ECU instantly determines the state of the vehicle and operates the brake actuator in order to apply the brakes to the slipping drive wheel. Furthermore, the ECM receives the signals from the skid control ECU and regulates the throttle in order to control the engine output. Thus, the system can constantly maintain a stable vehicle posture.

X106116E03
3.188,3.49 3.448,3.49 3.448,3.49 4.167,3.875 true 3.156,4.948 3.427,4.948 3.427,4.948 4.542,3.896 true 5.292,2.177 5.073,2.177 5.073,2.177 4.833,2.781 true 2.5,3.26 2.292,3.26 2.292,3.26 2.208,2.802 true 1.302,2.771 1.094,2.771 1.094,2.771 1.01,2.313 true 5.771,2.667 5.5,2.667 5.5,2.667 4.979,3.563 true 2.99,3.417 3.188,3.635 0.198,0.219 10 false *1 2.958,4.865 3.167,5.073 0.208,0.208 10 false *2 0.167,0.094 0.438,0.417 0.271,0.323 12 false *a: 5.313,2.104 5.521,2.313 0.208,0.208 10 false *b 1.323,2.688 1.531,2.896 0.208,0.208 10 false *b 2.531,3.198 2.74,3.406 0.208,0.208 10 false *b 5.823,2.573 6.031,2.781 0.208,0.208 10 false *c 3.115,0.563 3.323,0.771 0.208,0.208 10 false *A 4.25,1.063 4.458,1.271 0.208,0.208 10 false *B

Text in Illustration
*A Without TRC *B With TRC
*1

Brake Actuator Assembly

-

Skid Control ECU



*2

ECM

-

Regulating the throttle to control the engine output



*a Driving condition on road with different surface friction characteristics *b Slippery Surface
*c Brake the slipping drive wheel - -



f.

Vehicle Stability Control (VSC)

i.

The followings are two examples that can be considered as circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the motive force and the brakes at each wheel when the vehicle is under one of the conditions indicated below.

X106023E01
1.914,2.317 2.165,2.493 0.252,0.175 10 *a 4.522,2.317 4.774,2.493 0.252,0.175 10 *b

Text in Illustration
*a Front Wheel Skid Tendency *b Rear Wheel Skid Tendency


ii.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate and the vehicle's lateral acceleration, which are then calculated by the skid control ECU.


iii.

Whether or not the vehicle is in the state of front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the yaw rate (a target yaw rate that is determined by the vehicle speed and steering angle) that should be rightfully generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the locus of travel. Thus, the skid control ECU determines that there is a large tendency to front wheel skid.

X106024E01
3.68,0.287 3.932,0.463 0.252,0.175 10 *a 4.506,0.772 4.758,0.948 0.252,0.175 10 *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel (Based on the Target Yaw Rate)


iv.

Whether the vehicle is in the state of the rear wheel skid or not is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle and the slip angular velocity are large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X106025E01
3.868,0.822 4.18,0.461 4.18,0.461 4.375,0.461 false 3.79,0.898 3.559,0.63 3.559,0.63 3.364,0.63 false 4.087,0.589 4.291,0.793 0.205,0.205 10 *a 3.187,0.544 3.392,0.749 0.205,0.205 10 *b 4.404,0.388 4.608,0.593 0.205,0.205 10 *c

Text in Illustration
*a Movement of Vehicle *b Direction of Travel of the Vehicle's Center of Gravity
*c Slip Angle - -


v.

When the skid control ECU determines that the vehicle has a tendency to front wheel skid or rear wheel skid, it decreases the engine output and applies the brake of a front or rear wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the front wheels and rear wheel of the inner circle of the turn in order to help restrain the front wheel skid tendency.

X106026E03
4.375,0.74 4.698,0.427 4.698,0.427 4.896,0.427 true 4.927,0.333 5.135,0.542 0.208,0.208 10 false *a

Text in Illustration (Making a Right Turn)
*a Control Moment - -
V100135

Brake Force - -


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured.

X106027E01
4.287,0.756 4.613,0.379 4.613,0.379 4.807,0.379 false 4.847,0.312 5.052,0.517 0.205,0.205 10 *a

Text in Illustration (Making a Right Turn)
*a Control Moment - -
V100135

Brake Force - -



g.

Engine Output Control during TRC or VSC Operation

i.

During the TRC or VSC operation, the skid control ECU outputs the engine output control signal to the ECM. Upon receiving this signal, the ECM inhibits the engine output.

X106028E04
0.104,7.427 5.531,7.813 5.427,0.385 10 false *: The wheel cylinder that activates varies depending on the condition of the vehicle 0.677,5.729 1.521,6.99 0.844,1.26 10 false Brake Wheel Cylinder Fluid Pressure* 0.635,4.313 1.656,4.729 1.021,0.417 10 false Engine Torque 5.698,6.729 6.073,7.021 0.375,0.292 10 false Time 5.698,5.146 6.073,5.438 0.375,0.292 10 false Time 5.698,3.583 6.073,3.875 0.375,0.292 10 false Time 2.25,1.927 2.521,2.219 0.271,0.292 10 false (A) 4.615,0.396 6.792,0.688 2.177,0.292 10 false (A): Start of engine output control 4.625,0.719 6.802,1.01 2.177,0.292 10 false (B): Start of brake control 4.625,1.031 6.802,1.323 2.177,0.292 10 false (C): Brake control completed 4.625,1.344 7.042,1.708 2.417,0.365 10 false (D): Engine output control completed 2.542,1.927 2.813,2.219 0.271,0.292 10 false (B) 4.573,1.938 4.844,2.229 0.271,0.292 10 false (C) 4.875,1.938 5.146,2.229 0.271,0.292 10 false (D) 0.438,2.813 1.656,3.229 1.219,0.417 10 false Vehicle Condition 0.271,1.438 2,2.115 1.729,0.677 10 false Level of Strong Front Wheel Skid or Rear Wheel Skid




FUNCTION


a.

VSC OFF Switch (Models with ABS with EBD, Brake Assist, TRC and VSC)

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on the dirt road, the engine output control is stopped to maintain drive torque.


ii.

The VSC OFF switch can select the 3 modes (Normal Mode, TRC-OFF Mode, VSC-OFF Mode). When the VSC OFF switch is pressed briefly, TRC-OFF Mode is entered and the TRC function will be disabled. When the VSC OFF switch is pressed and held for 3 seconds or more, VSC-OFF Mode is entered and the TRC and VSC functions will be disabled.


iii.

After the power source is turned off in the TRC-OFF Mode or VSC-OFF Mode, turning the power source on again selects the Normal Mode. The system also enters Normal Mode automatically when the vehicle speed increases.

X106029E10
3.167,0.771 4.625,1.052 1.458,0.281 10 false Normal Mode 2.104,2.042 3.563,2.323 1.458,0.281 10 false VSC-OFF Mode 0.604,2.969 5.323,3.25 4.719,0.281 10 false : VSC OFF Switch Operation (Briefly press) 0.604,3.333 5.323,3.615 4.719,0.281 10 false : VSC OFF Switch Operation (Press and hold for 3 seconds or more) 4.073,2.052 5.531,2.333 1.458,0.281 10 false TRC-OFF Mode


iv.

The operations of the brake control functions in each mode are as follows:

Item Brake Control Function TRC OFF Indicator Light VSC OFF Indicator Light
TRC VSC
Normal Mode ○ ○ Light Off Light Off
TRC-OFF Mode - ○ Light On Light Off
VSC-OFF Mode - -* Light On Light On

○: Controllable

-: Not Controllable


HINT:

*: The control is effected during braking or while the yaw rate is large.





CONSTRUCTION


a.

Brake Actuator Assembly

i.

The brake actuator assembly consists of the actuator portion and skid control ECU.


ii.

The actuator portion regulates the hydraulic brake pressure to each wheel cylinder.

X106030E03
2.885,0.719 2.667,0.531 2.667,0.531 2.521,0.531 true 2.719,1.042 2.5,0.854 2.5,0.854 2.354,0.854 true 3.167,0.76 2.875,0.302 2.875,0.302 2.729,0.302 true 3.688,0.958 3.958,0.635 3.958,0.635 4.115,0.635 true 4.479,1.146 4.75,0.823 4.75,0.823 4.906,0.823 true 2.479,1.281 2.198,1.604 2.198,1.604 2.052,1.604 true 3.313,1.458 2.833,2.5 2.833,2.5 2.677,2.5 true 3.427,0.802 3.688,0.385 3.688,0.385 3.844,0.385 true 4.927,0.729 5.177,0.906 0.25,0.177 10 false *1 4.156,0.573 4.406,0.75 0.25,0.177 10 false *f 3.875,0.302 4.125,0.479 0.25,0.177 10 false *e 2.573,0.219 2.823,0.396 0.25,0.177 10 false *d 2.354,0.448 2.604,0.625 0.25,0.177 10 false *c 2.188,0.771 2.438,0.948 0.25,0.177 10 false *b 1.875,1.51 2.125,1.688 0.25,0.177 10 false *a 2.49,2.417 2.74,2.594 0.25,0.177 10 false *a

Text in Illustration (ABS with EBD:)
*1 Skid Control ECU - -
*a From Master Cylinder *b Actuator Portion
*c To Front Wheel Cylinder RH *d To Rear Wheel Cylinder LH
*e To Rear Wheel Cylinder RH *f To Front Wheel Cylinder LH

X106031E03
2.833,0.677 2.615,0.5 2.615,0.5 2.469,0.5 true 2.656,0.927 2.438,0.74 2.438,0.74 2.281,0.74 true 3.094,0.698 2.813,0.24 2.813,0.24 2.656,0.24 true 3.625,0.885 3.896,0.563 3.896,0.563 4.042,0.563 true 4.406,1.208 4.688,0.885 4.688,0.885 4.833,0.885 true 2.365,1.333 2.083,1.656 2.083,1.656 1.938,1.656 true 3.208,1.521 2.729,2.563 2.729,2.563 2.583,2.563 true 3.365,0.729 3.635,0.313 3.635,0.313 3.781,0.313 true 4.865,0.802 5.115,0.979 0.25,0.177 10 false *1 4.083,0.49 4.333,0.667 0.25,0.177 10 false *f 3.813,0.229 4.063,0.406 0.25,0.177 10 false *e 2.479,0.167 2.729,0.344 0.25,0.177 10 false *d 2.313,0.417 2.563,0.594 0.25,0.177 10 false *c 2.094,0.677 2.344,0.854 0.25,0.177 10 false *b 1.76,1.563 2.01,1.74 0.25,0.177 10 false *a 2.417,2.469 2.667,2.646 0.25,0.177 10 false *a

Text in Illustration (ABS with EBD, Brake Assist, TRC and VSC:)
*1 Skid Control ECU - -
*a From Master Cylinder *b Actuator Portion
*c To Front Wheel Cylinder RH *d To Rear Wheel Cylinder LH
*e To Rear Wheel Cylinder RH *f To Front Wheel Cylinder LH


iii.

The brake actuator assembly is constructed with the following hydraulic circuit:

X106032E02
2.063,2.76 1.771,2.594 true 2.063,2.76 2.333,2.583 true 4.958,2.76 4.677,2.594 true 4.948,2.76 5.219,2.583 true 2.063,4.76 1.771,4.333 true 2.063,4.76 2.333,4.323 true 4.948,4.76 4.667,4.333 true 4.948,4.76 5.219,4.323 true 3.5,2.75 3.219,2.26 true 3.5,2.75 3.771,2.25 true 3.5,5.167 3.198,4.958 true 3.5,5.167 3.781,4.958 true 2.135,0.208 2.333,0.396 0.198,0.188 10 false *a 4.646,0.208 4.844,0.396 0.198,0.188 10 false *a 3.406,0.781 3.604,0.969 0.198,0.188 10 false *1 3.406,2.802 3.604,2.99 0.198,0.188 10 false *3 3.406,5.208 3.604,5.396 0.198,0.188 10 false *5 2.781,6.458 2.979,6.646 0.198,0.188 10 false *7 1.156,6.458 1.354,6.646 0.198,0.188 10 false *6 5.677,6.458 5.875,6.646 0.198,0.188 10 false *9 4.052,6.458 4.25,6.646 0.198,0.188 10 false *8 1.99,2.802 2.188,2.99 0.198,0.188 10 false *2 4.865,2.802 5.063,2.99 0.198,0.188 10 false *2 1.99,4.792 2.188,4.979 0.198,0.188 10 false *4 4.865,4.792 5.063,4.979 0.198,0.188 10 false *4

Text in Illustration (ABS with EBD:)
*1 Brake Actuator Assembly *2 Pressure Holding Solenoid Valve
*3 Pump *4 Pressure Reduction Solenoid Valve
*5 Reservoir *6 Front Wheel Cylinder LH
*7 Rear Wheel Cylinder RH *8 Rear Wheel Cylinder LH
*9 From Master Cylinder - -
*a From Master Cylinder - -

X106033E05
2.01,3.646 1.729,3.49 true 2.01,3.646 2.281,3.479 true 5.177,3.646 4.896,3.49 true 5.177,3.646 5.448,3.479 true 2.01,5.667 1.729,5.24 true 2.01,5.667 2.281,5.229 true 5.177,5.667 4.896,5.24 true 5.177,5.667 5.448,5.229 true 3.583,3.271 3.208,2.75 true 3.583,3.271 3.979,2.75 true 3.594,6.073 3.292,5.865 true 3.594,6.073 3.875,5.865 true 1.073,1.865 0.594,1.865 true 6.104,1.865 6.625,1.865 true 1.51,0.25 1.74,0.458 0.229,0.208 10 false *a 5.542,0.25 5.771,0.458 0.229,0.208 10 false *a 3.51,0.708 3.74,0.917 0.229,0.208 10 false *1 3.51,3.333 3.74,3.542 0.229,0.208 10 false *5 1.938,3.698 2.135,3.865 0.198,0.167 10 false *4 5.115,3.698 5.313,3.865 0.198,0.167 10 false *4 1.938,5.719 2.135,5.885 0.198,0.167 10 false *6 5.115,5.719 5.313,5.885 0.198,0.167 10 false *6 3.51,6.146 3.74,6.354 0.229,0.208 10 false *7 2.74,7.323 2.969,7.531 0.229,0.208 10 false *9 1.125,7.323 1.354,7.531 0.229,0.208 10 false *8 5.875,7.323 6.156,7.531 0.281,0.208 10 false *11 4.26,7.323 4.573,7.531 0.313,0.208 10 false *10 5.375,1.021 5.604,1.229 0.229,0.208 10 false *2 6.698,1.792 6.927,2 0.229,0.208 10 false *3 0.385,1.792 0.615,2 0.229,0.208 10 false *3

Text in Illustration (ABS with EBD, Brake Assist, TRC and VSC:)
*1 Brake Actuator Assembly *2 Master Cylinder Pressure Sensor
*3 Master Cylinder Cut Solenoid Valve *4 Pressure Holding Solenoid Valve
*5 Pump *6 Pressure Reduction Solenoid Valve
*7 Reservoir *8 Front Wheel Cylinder LH
*9 Rear Wheel Cylinder RH *10 Rear Wheel Cylinder LH
*11 Front Wheel Cylinder RH - -
*a From Master Cylinder - -



b.

Speed Sensor

i.

An active type speed sensor is used. This sensor contains a Hall IC.


ii.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.


iii.

An active type speed sensor uses a Hall IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.


iv.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.

X106034E05
5.688,3.198 5.25,3.198 true 4.354,6.927 4.844,6.583 4.844,6.583 4.979,6.583 true 1.615,5.667 3.198,6.146 1.583,0.479 10 false Vehicle Speed 1.573,6.927 3.156,7.406 1.583,0.479 10 false Sensor Output 3.521,7.271 5.104,7.75 1.583,0.479 10 false Time 1.604,4.406 3.844,4.885 2.24,0.479 10 false N and S Poles Arrangement 5.021,6.5 6.604,6.979 1.583,0.479 10 false Digital Pulses 5.75,3.125 7.073,3.604 1.323,0.479 10 false SPEED SENSOR 3.99,1.323 4.51,1.51 0.521,0.188 10 false Hall IC 2.031,2.063 3.313,2.25 1.281,0.188 10 false Sensor Rotor



c.

Yaw Rate and Deceleration Sensor (w/ Built-in Type Yaw rate Sensor)

i.

The yaw rate and deceleration sensor is built into the airbag sensor assembly.


ii.

The yaw rate sensor detects acceleration in the horizontal forward-backward and left-right directions using the signals from 2 acceleration sensors, and transmits signals to the skid control ECU.

X106035E03
1.167,1.802 0.729,2.25 0.729,2.25 0.531,2.25 true 0.344,2.167 0.552,2.375 0.208,0.208 10 false *1

Text in Illustration
*1

Airbag Sensor Assembly

-

Yaw Rate and Deceleration Sensor



- -
V100135

Front - -

NOTICE:

After replacing the airbag sensor assembly, or the skid control ECU, initialization of the yaw rate and deceleration sensor is required. For the actual procedure, refer to the Repair Manual.




d.

Yaw Rate and Deceleration Sensor (w/ Separate Type Yaw Rate Sensor)

i.

The yaw rate and deceleration sensor (yaw rate sensor) detects acceleration in the horizontal forward-backward and left-right directions using the signals from 2 acceleration sensors, which are fitted at an angle of 45° to the front and back directions of the vehicle body, and transmits signals to the skid control ECU.

X106901E02
1.74,1.75 1.313,2.177 1.313,2.177 1.156,2.177 true 5.844,1.208 6.063,1.427 0.219,0.219 10 false *a 0.938,2.094 1.146,2.313 0.208,0.219 10 false *1

Text in Illustration
*1 Yaw Rate and Deceleration Sensor (Yaw Rate Sensor) - -
*a 45° - -
V100135

Front - -

NOTICE:

After replacing the yaw rate and deceleration sensor (yaw rate sensor), or the skid control ECU, initialization of the yaw rate and deceleration sensor (yaw rate sensor) is required. For the actual procedure, refer to the Repair Manual.




e.

Steering Angle Sensor

i.

The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.


ii.

The steering angle sensor contains two sets of magnetic reluctance elements that detect the rotational movement of a magnet that is built into the detection gear. Thus, the sensor detects the changes that occur in the magnetic reluctance elements along with the rotational movement of the detection gear, in order to detect the rotational movement of the steering wheel.

X106036E03
3.25,1.875 2.938,2.333 2.938,2.333 2.708,2.333 true 3.677,1.813 4.25,2.229 true 3.865,1.74 4.25,2.229 4.25,2.229 4.479,2.229 true 2.521,2.24 2.75,2.479 0.229,0.24 10 false *1 4.521,2.135 4.75,2.375 0.229,0.24 10 false *2

Text in Illustration
*1 Steering Angle Sensor *2 Detection Gear

NOTICE:

Do not remove the steering angle sensor from the spiral cable. If there is a malfunction in the steering angle sensor, replace the spiral cable with steering angle sensor.





OPERATION


a.

ABS with EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of the each wheel cylinder in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.

Not Activated Normal Braking
Activated Increase Mode
Hydraulic Circuit
X132649E02
0.979,0.917 1.156,0.917 1.156,0.917 1.708,1.396 true 0.958,2.167 1.167,2.167 1.167,2.167 1.708,2.854 true 0.542,0.823 0.979,1.135 0.438,0.313 10 false Port A 0.521,2.073 0.958,2.375 0.438,0.302 10 false Port B 1.26,3.99 2.438,4.563 1.177,0.573 10 false To Wheel Cylinder

Pressure Holding Valve (Port A) OFF (Open)
Pressure Reduction Valve (Port B) OFF (Closed)
Brake Wheel Cylinder Pressure Increased

Not Activated -
Activated Holding Mode
Hydraulic Circuit
X132650

Pressure Holding Valve (Port A) ON (Closed)
Pressure Reduction Valve (Port B) OFF (Closed)
Brake Wheel Cylinder Pressure Held

Not Activated -
Activated Reduction Mode
Hydraulic Circuit
X132651E01
0.177,2.458 0.979,3.458 0.802,1 10 false To Reservoir and Pump 1.083,3.927 2.542,4.448 1.458,0.521 10 false From Wheel Cylinder

Pressure Holding Valve (Port A) ON (Closed)
Pressure Reduction Valve (Port B) ON (Open)
Brake Wheel Cylinder Pressure Reduced



b.

Brake Assist (Electrical Type)

i.

In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a greater fluid pressure than the master cylinder.

X106040E02
3.573,0.802 6.01,1.031 2.438,0.229 10 false BRAKE ACTUATOR ASSEMBLY 2.958,3.427 4.198,4.125 1.24,0.698 10 false MOTOR FAILSAFE RELAY 4.833,1.281 6.469,1.979 1.635,0.698 10 false MASTER CYLINDER CUT SOLENOID VALVES (2) 4.833,4.031 6.26,4.75 1.427,0.719 10 false MASTER CYLINDER PRESSURE SENSOR 4.833,2.406 6.51,2.604 1.677,0.198 10 false SOLENOID VALVES (8) 2.635,5.146 3.458,5.375 0.823,0.229 10 false CAN (V Bus) 4.833,3.219 5.906,3.427 1.073,0.208 10 false PUMP MOTOR 2.958,2.385 4.188,2.594 1.229,0.208 10 false SOLENOID RELAY 2.958,2.99 4.073,3.198 1.115,0.208 10 false MOTOR RELAY 2.875,4.198 4.333,4.406 1.458,0.208 10 false SKID CONTROL ECU 4.698,6.115 6.344,6.292 1.646,0.177 10 false ABS WARNING LIGHT 4.583,5.677 6.958,5.896 2.375,0.219 10 false COMBINATION METER ASSEMBLY 0.208,1.75 2.271,2.135 2.063,0.385 10 false FRONT SPEED SENSOR LH 0.208,1.271 2.25,1.667 2.042,0.396 10 false FRONT SPEED SENSOR RH 0.208,2.26 2.354,3.26 2.146,1 10 false REAR SPEED SENSOR RH (SKID CONTROL SENSOR WIRE RH) 0.208,3.427 2.375,4.458 2.167,1.031 10 false REAR SPEED SENSOR LH (SKID CONTROL SENSOR WIRE LH) 0.208,4.573 2.458,4.833 2.25,0.26 10 false STOP LIGHT SWITCH ASSEMBLY 0.24,5.635 0.708,5.823 0.469,0.188 10 false DLC3

X106060E07
2.417,3.219 2.74,2.542 2.74,2.542 2.604,2.542 true 2.396,4.656 2.042,5.896 2.042,5.896 1.906,5.896 true 3.594,6.219 3.354,5.917 true 3.594,6.208 3.823,5.917 true 4.781,4.646 5.146,5.885 5.146,5.885 5.281,5.885 true 3.594,3.417 3.115,3.042 true 3.594,3.417 4.063,3.052 true 4.74,3.229 4.427,2.552 4.427,2.552 4.563,2.552 true 0.677,1.917 0.823,1.917 0.823,1.917 1.344,2.115 true 0.677,3.542 0.823,3.542 0.823,3.542 1.583,3.24 true 0.688,4.896 0.833,4.896 0.833,4.896 1.594,4.573 true 6.49,1.917 6.333,1.917 6.333,1.917 5.823,2.115 true 6.49,3.542 6.354,3.542 6.354,3.542 5.583,3.24 true 6.49,4.896 6.344,4.896 6.344,4.896 5.583,4.573 true 1.552,0.25 3.073,0.635 1.521,0.385 10 false From Master Cylinder 0.156,1.823 0.74,2.052 0.583,0.229 10 false Port (A) 2.073,2.479 2.646,2.698 0.573,0.219 10 false Port (D) 3.177,6.302 4.115,6.521 0.938,0.219 10 false RESERVOIR 0.844,7.156 1.635,7.813 0.792,0.656 10 false Front Wheel Cylinder LH 2.49,7.156 3.25,7.802 0.76,0.646 10 false Rear Wheel Cylinder RH 4.052,7.177 4.813,7.792 0.76,0.615 10 false Rear Wheel Cylinder LH 5.625,7.146 6.396,7.76 0.771,0.615 10 false Front Wheel Cylinder RH 4.615,2.5 5.167,2.719 0.552,0.219 10 false Port (E) 6.552,1.844 7.125,2.063 0.573,0.219 10 false Port (B) 6.542,3.469 7.115,3.688 0.573,0.219 10 false Port (F) 6.552,4.823 7.104,5.021 0.552,0.198 10 false Port (J) 5.333,5.813 5.906,6.031 0.573,0.219 10 false Port (I) 1.406,5.802 1.979,6.021 0.573,0.219 10 false Port (H) 1.281,2.708 1.5,2.885 0.219,0.177 10 false (1) 1.51,3.833 1.76,4.052 0.25,0.219 10 false (3) 1.51,5.167 1.76,5.375 0.25,0.208 10 false (7) 2.333,3.833 2.583,4.042 0.25,0.208 10 false (4) 5.74,2.708 5.958,2.896 0.219,0.188 10 false (2) 4.688,3.823 4.917,4.031 0.229,0.208 10 false (5) 5.5,3.813 5.729,4.01 0.229,0.198 10 false (6) 2.333,5.156 2.583,5.375 0.25,0.219 10 false (8) 4.688,5.167 4.917,5.354 0.229,0.188 10 false (9) 5.458,5.167 5.781,5.385 0.323,0.219 10 false (10) 0.177,3.458 0.865,3.781 0.688,0.323 10 false Port (C) 0.177,4.813 0.813,5.083 0.635,0.271 10 false Port (G) 4.323,0.271 5.75,0.729 1.427,0.458 10 false From Master Cylinder 2.583,0.844 4.771,1.188 2.188,0.344 10 false BRAKE ACTUATOR ASSEMBLY 2.979,1.229 5.76,1.615 2.781,0.385 10 false MASTER CYLINDER PRESSURE SENSOR 3.375,3.438 3.885,3.802 0.51,0.365 10 false PUMP

Item Port Not Activated Activated
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON*
(2) (B) OFF (Open) ON*
Pressure Holding Solenoid Valve (3) (C) OFF (Open) ←
(4) (D) OFF (Open) ←
(5) (E) OFF (Open) ←
(6) (F) OFF (Open) ←
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ←
(8) (H) OFF (Close) ←
(9) (I) OFF (Close) ←
(10) (J) OFF (Close) ←
Pump OFF ON

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "close" according to the operating condition by adjusting continually.




c.

TRC

i.

The fluid pressure generated by the pump motor is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding and pressure increase modes to control the slippage of the drive wheels. The diagram below shows the hydraulic circuit in the pressure increase mode when the TRC is activated. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on/off according to the ABS with EBD operation pattern.

X106042E06
0.302,2.375 2.563,3 2.26,0.625 10 false REAR SPEED SENSOR RH (SKID CONTROL SENSOR WIRE RH) 0.302,3.208 2.521,3.813 2.219,0.604 10 false REAR SPEED SENSOR LH (SKID CONTROL SENSOR WIRE LH) 0.333,3.99 2.656,4.333 2.323,0.344 10 false STOP LIGHT SWITCH ASSEMBLY 0.865,4.5 2.604,4.823 1.74,0.323 10 false VSC OFF SWITCH 0.531,1.365 2.635,1.719 2.104,0.354 10 false FRONT SPEED SENSOR RH 0.531,1.844 2.625,2.229 2.094,0.385 10 false FRONT SPEED SENSOR LH 3.396,2.292 4.635,2.688 1.24,0.396 10 false SOLENOID RELAY 3.542,3.01 4.813,3.365 1.271,0.354 10 false MOTOR RELAY 3.375,3.5 4.594,4.115 1.219,0.615 10 false MOTOR FAILSAFE RELAY 4.021,0.927 6.542,1.354 2.521,0.427 10 false BRAKE ACTUATOR ASSEMBLY 3.302,1.698 4.833,2.198 1.531,0.5 10 false SKID CONTROL ECU 5.188,1.406 6.833,2.021 1.646,0.615 10 false MASTER CYLINDER CUT SOLENOID VALVES (2) 5.25,2.375 6.885,2.844 1.635,0.469 10 false SOLENOID VALVES (8) 5.573,3.198 6.854,3.677 1.281,0.479 10 false PUMP MOTOR 5.375,3.854 6.813,4.521 1.438,0.667 10 false MASTER CYLINDER PRESSURE SENSOR 4.396,5.667 6.823,6.073 2.427,0.406 10 false COMBINATION METER ASSEMBLY 4.646,6.177 6.76,6.51 2.115,0.333 10 false TRC OFF INDICATOR LIGHT 4.792,6.646 6.781,6.979 1.99,0.333 10 false SLIP INDICATOR LIGHT 4.469,7.896 6.531,8.604 2.063,0.708 10 false THROTTLE WITH MOTOR BODY ASSEMBLY 4.469,8.698 6.792,9.031 2.323,0.333 10 false THROTTLE POSITION SENSOR 4.5,9.177 6.781,9.521 2.281,0.344 10 false THROTTLE CONTROL MOTOR 5.365,7.323 6.667,7.615 1.302,0.292 10 false DLC3 3.542,6.469 4.021,6.917 0.479,0.448 10 false CAN (V Bus) 3.25,8.531 3.656,9.052 0.406,0.521 10 false ECM 0.458,6.365 2.646,6.688 2.188,0.323 10 false AIRBAG SENSOR ASSEMBLY 0.375,6.823 2.531,7.458 2.156,0.635 10 false YAW RATE AND DECELERATION SENSOR 0.531,5.646 2.677,5.99 2.146,0.344 10 false STEERING ANGLE SENSOR 0.188,0.25 3.354,0.792 3.167,0.542 12 false w/ Built-in Type Yaw Rate Sensor:

X106813E03
0.135,0.167 3.333,0.625 3.198,0.458 12 false w/ Separate Type Yaw Rate Sensor: 0.458,1.385 2.698,1.729 2.24,0.344 10 false FRONT SPEED SENSOR RH 0.5,1.865 2.646,2.208 2.146,0.344 10 false FRONT SPEED SENSOR LH 0.333,4.021 2.719,4.354 2.385,0.333 10 false STOP LIGHT SWITCH ASSEMBLY 0.875,4.51 2.625,4.854 1.75,0.344 10 false VSC OFF SWITCH 0.542,5.656 2.729,5.969 2.188,0.313 10 false STEERING ANGLE SENSOR 3.021,0.844 5.396,1.125 2.375,0.281 10 false BRAKE ACTUATOR ASSEMBLY 3.313,1.604 4.729,2.052 1.417,0.448 10 false SKID CONTROL ECU 3.313,2.323 4.698,2.656 1.385,0.333 10 false SOLENOID RELAY 3.438,3.042 4.635,3.375 1.198,0.333 10 false MOTOR RELAY 5.292,2.385 6.875,2.854 1.583,0.469 10 false SOLENOID VALVES (8) 5.573,3.271 6.885,3.635 1.313,0.365 10 false PUMP MOTOR 4.396,5.708 6.938,6.115 2.542,0.406 10 false COMBINATION METER ASSEMBLY 4.635,6.198 6.719,6.542 2.083,0.344 10 false TRC OFF INDICATOR LIGHT 4.781,6.646 6.677,6.979 1.896,0.333 10 false SLIP INDICATOR LIGHT 5.354,7.333 6.75,7.625 1.396,0.292 10 false DLC3 4.552,8.729 6.729,9.167 2.177,0.438 10 false THROTTLE POSITION SENSOR 4.563,9.177 6.625,9.615 2.063,0.438 10 false THROTTLE CONTROL MOTOR 3.26,8.531 3.688,8.813 0.427,0.281 10 false ECM 0.333,6.646 2.51,7.25 2.177,0.604 10 false YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) 3.354,3.573 4.542,4.156 1.188,0.583 10 false MOTOR FAILSAFE RELAY 5.229,1.385 6.823,2.031 1.594,0.646 10 false MASTER CYLINDER CUT SOLENOID VALVES (2) 0.365,2.385 2.51,3.021 2.146,0.635 10 false REAR SPEED SENSOR RH (SKID CONTROL SENSOR WIRE RH) 0.354,3.208 2.521,3.844 2.167,0.635 10 false REAR SPEED SENSOR LH (SKID CONTROL SENSOR WIRE LH) 5.313,3.875 6.708,4.521 1.396,0.646 10 false MASTER CYLINDER PRESSURE SENSOR 4.646,7.948 6.292,8.646 1.646,0.698 10 false THROTTLE WITH MOTOR BODY ASSEMBLY 3.563,6.469 4.042,6.823 0.479,0.354 10 false CAN (V Bus)


ii.

By way of example, the brake hydraulic circuit under the pressure increase mode of TRC is shown below.

X106065E07
2.417,3.24 2.729,2.552 2.729,2.552 2.594,2.552 true 2.406,4.615 2.052,5.844 2.052,5.844 1.917,5.844 true 3.594,6.198 3.354,5.896 true 3.594,6.208 3.833,5.917 true 4.76,4.604 5.115,5.844 5.115,5.844 5.25,5.844 true 3.594,3.427 3.094,3.042 true 3.594,3.427 4.073,3.031 true 4.74,3.24 4.427,2.552 4.427,2.552 4.563,2.552 true 0.667,1.906 0.823,1.906 0.823,1.906 1.344,2.104 true 0.677,3.531 0.813,3.531 0.813,3.531 1.583,3.229 true 0.688,4.917 0.833,4.917 0.833,4.917 1.594,4.594 true 6.469,1.917 6.323,1.917 6.323,1.917 5.802,2.115 true 6.479,3.542 6.333,3.542 6.333,3.542 5.573,3.24 true 6.479,4.885 6.333,4.885 6.333,4.885 5.573,4.563 true 1.521,0.25 3.115,0.646 1.594,0.396 10 false From Master Cylinder 0.146,1.833 0.729,2.063 0.583,0.229 10 false Port (A) 2.073,2.469 2.646,2.688 0.573,0.219 10 false Port (D) 3.177,6.281 4.115,6.5 0.938,0.219 10 false RESERVOIR 0.844,7.135 1.646,7.833 0.802,0.698 10 false Front Wheel Cylinder LH 2.49,7.135 3.26,7.854 0.771,0.719 10 false Rear Wheel Cylinder RH 4.052,7.135 4.813,7.792 0.76,0.656 10 false Rear Wheel Cylinder LH 5.625,7.125 6.396,7.833 0.771,0.708 10 false Front Wheel Cylinder RH 4.625,2.5 5.177,2.719 0.552,0.219 10 false Port (E) 6.521,1.844 7.094,2.063 0.573,0.219 10 false Port (B) 6.531,3.469 7.104,3.688 0.573,0.219 10 false Port (F) 6.542,4.792 7.094,4.99 0.552,0.198 10 false Port (J) 5.323,5.781 5.896,6 0.573,0.219 10 false Port (I) 1.406,5.76 1.979,5.979 0.573,0.219 10 false Port (H) 1.281,2.688 1.5,2.865 0.219,0.177 10 false (1) 1.5,3.802 1.75,4.021 0.25,0.219 10 false (3) 1.51,5.156 1.76,5.365 0.25,0.208 10 false (7) 2.354,3.802 2.604,4.01 0.25,0.208 10 false (4) 5.74,2.688 5.958,2.875 0.219,0.188 10 false (2) 4.688,3.823 4.917,4.031 0.229,0.208 10 false (5) 5.5,3.813 5.729,4.01 0.229,0.198 10 false (6) 2.344,5.167 2.594,5.385 0.25,0.219 10 false (8) 4.688,5.156 4.917,5.344 0.229,0.188 10 false (9) 5.458,5.156 5.781,5.375 0.323,0.219 10 false (10) 0.156,3.448 0.844,3.771 0.688,0.323 10 false Port (C) 0.177,4.833 0.813,5.104 0.635,0.271 10 false Port (G) 4.323,0.26 5.698,0.708 1.375,0.448 10 false From Master Cylinder 2.583,0.854 4.844,1.188 2.26,0.333 10 false BRAKE ACTUATOR ASSEMBLY 2.969,1.219 5.813,1.625 2.844,0.406 10 false MASTER CYLINDER PRESSURE SENSOR 3.375,3.458 3.865,3.844 0.49,0.385 10 false PUMP

Item Port Not Activated Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ← ←
(2) (B) OFF (Open) ON* ← ←
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) ← ← ON (Close)
(6) (F) OFF (Open) ← ← ON (Close)
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ← ← ON (Open)
(10) (J) OFF (Close) ← ← ON (Open)
Brake Wheel Cylinder Pressure Right - - Increase Hold Reduce
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) ON (Close) ← ←
(5) (E) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (8) (H) OFF (Close) ← ← ←
(9) (I) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - - - -
Left - - - - -
Pump OFF ON ← ←

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "close" according to the operating condition by adjusting continually.




d.

VSC

i.

The VSC, by way of solenoid valves, controls the fluid pressure that is generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding and pressure increase modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.

X106044E05
0.365,2.385 2.542,3.042 2.177,0.656 10 false REAR SPEED SENSOR RH (SKID CONTROL SENSOR WIRE RH) 0.344,3.208 2.479,3.865 2.135,0.656 10 false REAR SPEED SENSOR LH (SKID CONTROL SENSOR WIRE LH) 0.354,4 2.625,4.344 2.271,0.344 10 false STOP LIGHT SWITCH ASSEMBLY 0.844,4.5 2.719,4.854 1.875,0.354 10 false VSC OFF SWITCH 0.51,1.365 2.5,1.813 1.99,0.448 10 false FRONT SPEED SENSOR RH 0.531,1.854 2.406,2.219 1.875,0.365 10 false FRONT SPEED SENSOR LH 3.406,2.302 4.74,2.646 1.333,0.344 10 false SOLENOID RELAY 3.51,3.01 4.74,3.354 1.229,0.344 10 false MOTOR RELAY 3.375,3.542 4.604,4.188 1.229,0.646 10 false MOTOR FAILSAFE RELAY 4.021,0.854 6.49,1.281 2.469,0.427 10 false BRAKE ACTUATOR ASSEMBLY 3.302,1.615 4.792,2.208 1.49,0.594 10 false SKID CONTROL ECU 5.219,1.417 6.854,2.042 1.635,0.625 10 false MASTER CYLINDER CUT SOLENOID VALVES (2) 5.271,2.354 6.865,2.844 1.594,0.49 10 false SOLENOID VALVES (8) 5.573,3.24 6.917,3.667 1.344,0.427 10 false PUMP MOTOR 5.375,3.865 6.802,4.521 1.427,0.656 10 false MASTER CYLINDER PRESSURE SENSOR 4.354,5.271 6.802,5.646 2.448,0.375 10 false COMBINATION METER ASSEMBLY 4.625,6.167 6.813,6.531 2.188,0.365 10 false TRC OFF INDICATOR LIGHT 4.615,5.729 6.781,6.063 2.167,0.333 10 false VSC OFF INDICATOR LIGHT 4.813,6.646 6.833,6.979 2.021,0.333 10 false SLIP INDICATOR LIGHT 4.531,7.917 6.594,8.615 2.063,0.698 10 false THROTTLE WITH MOTOR BODY ASSEMBLY 4.51,8.698 6.781,9.031 2.271,0.333 10 false THROTTLE POSITION SENSOR 4.583,9.177 6.75,9.531 2.167,0.354 10 false THROTTLE CONTROL MOTOR 5.344,7.313 6.625,7.646 1.281,0.333 10 false DLC3 3.573,6.448 4.063,6.896 0.49,0.448 10 false CAN (V Bus) 3.25,8.573 3.698,9.083 0.448,0.51 10 false ECM 0.51,6.365 2.635,6.698 2.125,0.333 10 false AIRBAG SENSOR ASSEMBLY 0.344,6.854 2.531,7.448 2.188,0.594 10 false YAW RATE AND DECELERATION SENSOR 0.563,5.625 2.708,5.99 2.146,0.365 10 false STEERING ANGLE SENSOR 0.208,0.156 3.354,0.729 3.146,0.573 12 false w/ Built-in Type Yaw Rate Sensor:

X106814E03
0.135,0.219 3.354,0.688 3.219,0.469 12 false w/ Separate Type Yaw Rate Sensor: 0.49,1.375 2.74,1.708 2.25,0.333 10 false FRONT SPEED SENSOR RH 0.542,1.844 2.719,2.208 2.177,0.365 10 false FRONT SPEED SENSOR LH 0.323,4.01 2.625,4.333 2.302,0.323 10 false STOP LIGHT SWITCH ASSEMBLY 0.917,4.51 2.635,4.854 1.719,0.344 10 false VSC OFF SWITCH 0.531,5.635 2.667,5.958 2.135,0.323 10 false STEERING ANGLE SENSOR 3.031,0.875 5.438,1.271 2.406,0.396 10 false BRAKE ACTUATOR ASSEMBLY 3.354,1.573 4.708,2.052 1.354,0.479 10 false SKID CONTROL ECU 3.333,2.302 4.604,2.677 1.271,0.375 10 false SOLENOID RELAY 3.427,3.031 4.625,3.365 1.198,0.333 10 false MOTOR RELAY 5.302,2.396 6.802,2.833 1.5,0.438 10 false SOLENOID VALVES (8) 5.573,3.24 6.781,3.625 1.208,0.385 10 false PUMP MOTOR 4.406,5.323 6.865,5.698 2.458,0.375 10 false COMBINATION METER ASSEMBLY 4.646,6.219 6.646,6.563 2,0.344 10 false TRC OFF INDICATOR LIGHT 4.656,5.74 6.698,6.115 2.042,0.375 10 false VSC OFF INDICATOR LIGHT 4.75,6.688 6.635,7.01 1.885,0.323 10 false SLIP INDICATOR LIGHT 5.406,7.323 6.708,7.646 1.302,0.323 10 false DLC3 4.573,8.719 6.771,9.104 2.198,0.385 10 false THROTTLE POSITION SENSOR 4.563,9.156 6.802,9.625 2.24,0.469 10 false THROTTLE CONTROL MOTOR 3.25,8.604 3.677,9.219 0.427,0.615 10 false ECM 0.333,6.615 2.521,7.26 2.188,0.646 10 false YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) 3.354,3.552 4.542,4.156 1.188,0.604 10 false MOTOR FAILSAFE RELAY 5.208,1.396 6.833,2.042 1.625,0.646 10 false MASTER CYLINDER CUT SOLENOID VALVES (2) 0.365,2.385 2.542,3 2.177,0.615 10 false REAR SPEED SENSOR RH (SKID CONTROL SENSOR WIRE RH) 0.365,3.219 2.521,3.813 2.156,0.594 10 false REAR SPEED SENSOR LH (SKID CONTROL SENSOR WIRE LH) 5.26,3.854 6.677,4.51 1.417,0.656 10 false MASTER CYLINDER PRESSURE SENSOR 4.615,7.948 6.656,8.594 2.042,0.646 10 false THROTTLE WITH MOTOR BODY ASSEMBLY 3.573,6.458 4.052,7.01 0.479,0.552 10 false CAN (V Bus)


ii.

In the front wheel skid restraining control, the brakes of the front wheels and rear wheel of the inner circle of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation pattern.

X106069E07
2.427,3.958 2.74,3.271 2.74,3.271 2.604,3.271 true 2.417,5.271 2.063,6.5 2.063,6.5 1.927,6.5 true 3.615,6.854 3.375,6.552 true 3.615,6.844 3.844,6.552 true 4.771,5.281 5.125,6.521 5.125,6.521 5.26,6.521 true 3.615,4.094 3.125,3.708 true 3.615,4.094 4.094,3.719 true 4.76,3.958 4.438,3.229 4.438,3.229 4.573,3.229 true 0.677,2.604 0.833,2.604 0.833,2.604 1.354,2.802 true 0.698,4.229 0.844,4.229 0.844,4.229 1.604,3.927 true 0.688,5.573 0.833,5.573 0.833,5.573 1.604,5.25 true 6.5,2.604 6.344,2.604 6.344,2.604 5.823,2.802 true 6.5,4.24 6.354,4.24 6.354,4.24 5.594,3.938 true 6.5,5.583 6.344,5.583 6.344,5.583 5.583,5.26 true 1.594,0.802 3.115,1.177 1.521,0.375 10 false From Master Cylinder 0.177,2.521 0.76,2.75 0.583,0.229 10 false Port (A) 2.083,3.188 2.656,3.406 0.573,0.219 10 false Port (D) 3.25,6.896 4.188,7.115 0.938,0.219 10 false RESERVOIR 0.865,7.958 1.771,8.354 0.906,0.396 10 false Front Wheel Cylinder RH 2.5,7.958 3.365,8.323 0.865,0.365 10 false Rear Wheel Cylinder LH 4.073,7.958 4.896,8.333 0.823,0.375 10 false Rear Wheel Cylinder RH 5.635,7.958 6.51,8.323 0.875,0.365 10 false Front Wheel Cylinder LH 4.615,3.167 5.167,3.385 0.552,0.219 10 false Port (E) 6.531,2.531 7.104,2.75 0.573,0.219 10 false Port (B) 6.552,4.167 7.125,4.385 0.573,0.219 10 false Port (F) 6.563,5.51 7.115,5.708 0.552,0.198 10 false Port (J) 5.313,6.448 5.885,6.667 0.573,0.219 10 false Port (I) 1.417,6.417 1.99,6.635 0.573,0.219 10 false Port (H) 1.292,3.375 1.51,3.552 0.219,0.177 10 false (1) 1.531,4.5 1.781,4.719 0.25,0.219 10 false (3) 1.531,5.833 1.781,6.042 0.25,0.208 10 false (7) 2.344,4.51 2.594,4.719 0.25,0.208 10 false (4) 5.76,3.385 5.979,3.573 0.219,0.188 10 false (2) 4.708,4.51 4.938,4.719 0.229,0.208 10 false (5) 5.521,4.5 5.75,4.698 0.229,0.198 10 false (6) 2.354,5.833 2.604,6.052 0.25,0.219 10 false (8) 4.708,5.844 4.938,6.031 0.229,0.188 10 false (9) 5.479,5.854 5.802,6.073 0.323,0.219 10 false (10) 0.188,4.125 0.875,4.448 0.688,0.323 10 false Port (C) 0.167,5.5 0.802,5.771 0.635,0.271 10 false Port (G) 4.302,0.792 5.781,1.229 1.479,0.438 10 false From Master Cylinder 2.573,1.354 4.771,1.74 2.198,0.385 10 false BRAKE ACTUATOR ASSEMBLY 2.969,1.813 5.781,2.167 2.813,0.354 10 false MASTER CYLINDER PRESSURE SENSOR 3.417,4.125 4.094,4.531 0.677,0.406 10 false PUMP

Front Wheel Skid Restraining Control
Item Port Not Activated Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON (Close)* ← ←
(2) (B) OFF (Open) ON (Close)* ← ←
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) ← ON (Close) ←
(6) (F) OFF (Open) ← ON (Close) ←
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ← ← ON (Open)
(10) (J) OFF (Close) ← ← ON (Open)
Brake Wheel Cylinder Pressure Right - - Increase Hold Reduce
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) ← ON (Close) ←
(5) (E) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (8) (H) OFF (Close) ← ← ON (Open)
(9) (I) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - Increase - -
Left - - - Hold Reduce
Pump OFF ON ← ←

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "closed" according to the operating condition by adjusting continually.



iii.

In the rear wheel skid restraining control, the brakes of the front wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The hydraulic circuit controls the rear wheel skid condition while the vehicle make a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation patterns.

Rear Wheel Skid Restraining Control
Item Port Not Activated Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ← ←
(2) (B) OFF (Open) ON* ← ←
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) ← ON (Close) ←
(6) (F) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ← ← ON (Open)
(10) (J) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - - - -
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) ON (Close) ← ←
(5) (E) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (8) (H) OFF (Close) ← ← ←
(9) (I) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - - - -
Left - - - - -
Pump OFF ON ← ←

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "closed" according to the operating condition by adjusting continually.





FAIL-SAFE


a.

In the event of a malfunction in the ABS, skid control ECU prohibits the brake control system.


b.

In the event of a malfunction in the EBD, the brake system is operated as long as possible even if the ABS is prohibited. If the EBD control becomes impossible, the brake warning light illuminates to inform the driver of that. In this case, the brake system is operated in the same condition as the brake system without the brake control system.


c.

In the event of a malfunction in the TRC and/or VSC, skid control ECU prohibits the TRC and VSC operation.


d.

If a communication malfunction occurs between the skid control ECU and the steering angle sensor, yaw rate and deceleration sensor, or ECM, the skid control ECU stops the TRC and VSC.


e.

When the ECM detects the Diagnostic Trouble Code (DTC), it will disable the TRC and VSC.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system (ABS with EBD), then the ABS warning light, brake warning light individually according to the function in which the malfunction has been detected, to alert the driver of the malfunction.


b.

If the skid control ECU detects a malfunction in the brake control system (ABS with EBD, brake assist, TRC and VSC), then the ABS warning light, brake warning light, or slip indicator light illuminate either individually or as a group according to the function in which the malfunction has been detected, to alert the driver of the malfunction.


c.

At the same time, the DTCs are stored in memory.


d.

This system has a sensor signal check (test mode) function.


e.

For details of the DTCs that are stored in skid control ECU memory and the DTCs that are output through the sensor signal check functions, see the Repair Manual.