Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.08–2014.07
NM19S0E _58 Vehicle Interior _051433 METER / GAUGE / DISPLAY _0247903 METER / GAUGE SYSTEM UN GENERAL/CONTROL/DETAILS F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


OPERATING CONDITION


a.

Eco Driving Indicator Light (Models with Automatic Transaxle and ABS)

i.

Eco Driving Indicator Light starts to operate when all of the following conditions are met:

Conditions Ignition switch is ON.
Engine is running.
Shift lever is in D.
When the vehicle is at a speed of 130 km/h (81 mph) or below.


ii.

Eco Driving Indicator Light stops operation when any of the following conditions is met:

Conditions Ignition switch is off.
Engine is stopping.
Shift lever is in any position other than D.
When the vehicle is at a speed of 130 km/h (81 mph) or over.




SYSTEM CONTROL


a.

Front Seat Belt Warning (Models for Australia)

i.

When the ignition switch is ON, this system detects the state of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the occupant detector sensor.


ii.

The front seat belt warning light located in the combination meter is used for both the driver and passenger seats.


iii.

After the ignition switch is turned ON, if the driver or front passenger has not fastened their seat belt, the seat belt warning light will begin flashing.


iv.

When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.


v.

If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.


vi.

While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.



b.

Front Seat Belt Warning (Models for G.C.C. Countries)

i.

When the ignition switch is ON, this system detects the state of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the occupant detector sensor.


ii.

The front seat belt warning light located in the combination meter is used for both the driver and passenger seats.


iii.

After the ignition switch is turned ON, if the driver's or front passenger's seat belt has remained unfastened for 1.8 seconds, the front seat belt warning light will flash for 6 seconds. And then, when either of the following conditions is met, the seat belt warning light will continue flashing; the driver's or front passenger's seat belt remains unfastened and the shift lever is in a position other than P for approximately 30 seconds or more, or the driver's or front passenger's seat belt remains unfastened and the seat belt warning buzzer sounds once. Furthermore, when the seat belt is not fastened within approximately 30 seconds from the time the seat belt warning buzzer started sounding periodically, the warning light will commence flashing at short intervals.


iv.

If the driver's or front passenger's seat belt is still unfastened even after the ignition switch is turned ON, the seat belt warning buzzer will sound 5 times. And then, if the driver's or front passenger's seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will sound once. Furthermore, when approximately 30 seconds has elapsed with the seat belt unfastened, the seat belt warning buzzer will start sounding periodically for 9.6 seconds. If the seat belt is not fastened within this 9.6 seconds, the seat belt warning buzzer will commence sounding at short intervals.


v.

While the seat belt warning light is flashing and the seat belt warning buzzer is sounding, fastening the seat belt will bring the warning light flashing and warning buzzer sounding to a stop.



c.

Eco Driving Indicator Light (Models with Automatic Transaxle and ABS)

i.

When the ECM determines that Eco driving (environment-friendly acceleration operation) is being performed, the ECM outputs an Eco Driving Indicator Light illumination request to the combination meter assembly that illuminates the Eco Driving Indicator Light.

Y101366E01
0.667,1.177 1.146,1.427 0.479,0.25 10 ECM 3.708,1.01 4.146,1.427 0.438,0.417 10 Meter ECU 4.74,1.396 6.375,1.646 1.635,0.25 10 Eco Driving Indicator Light 1.531,1.615 3.229,2.042 1.698,0.427 10 Eco Driving Indicator Light Illumination Request Signal 4.354,2.042 6.271,2.292 1.917,0.25 10 Combination Meter Assembly 1.969,0.896 2.885,1.146 0.917,0.25 10 CAN (V Bus)




FUNCTION


a.

Buzzer Function

i.

The table below shows the buzzer in the combination meter assembly:

Item
·

Front Seat Belt Warning*1*2

·

EPS Warning

·

Key Reminder*2

·

Engine Immobiliser Matching Completion Report

·

Speed Limiter Warning*2

·

Parking Brake On Driving Warning

·

Door Open Driving Warning

·

Light Reminder

·

Turn Flasher Sound



*1: Models for Australia

*2: Models for G.C.C. Countries




b.

Multi-information Display Function

Y111216E02
1.375,2.094 1.583,2.323 0.208,0.229 10 false *1 4.188,2.063 4.396,2.292 0.208,0.229 10 false *1 0.531,0.427 0.844,0.771 0.313,0.344 10 false *A 3.771,0.427 4.083,0.771 0.313,0.344 10 false *B

Text in Illustration
*A Models without Tachometer *B Models with Tachometer
*1 Multi-information Display - -

Display Area Display Display Item Outline
"a"
Y197627

Clock Display The clock is always displayed.
"b"
Y197628

Outside Temperature Display The outside temperature is always displayed.
"c"
Y197629

Odometer Display Displays the odometer.
Y197630

Trip Meter A Display Displays the trip meter A.
Y197631

Trip Meter B Display Displays the trip meter B.
Y197632

Instantaneous Fuel Consumption Display*1
·

Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

·

This display is updated constantly.


Y197633

Average Fuel Consumption After Refueling Display*1
·

Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption.

·

The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge.

·

This display is updated every 10 seconds.


Y197634

Drivable Distance Display*1
·

Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON.

·

This display is updated every 1 second.


Y197635

Average Vehicle Speed After Starting Display*1
·

Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the engine start signal.

·

This display is updated every 10 seconds.


Y197636

Dimming Mode Display Adjust the meter luminance.
Y197637

Y197638

Eco Driving Indicator Light Customizing Display*2 Customize Eco Driving Indicator Light.
"d"
Y197639

Shift Position Indicator*3 Displays shift position P, R, N, D or B of the automatic transaxle.
"e"
Y197626

Fuel Gauge Display Displays the remaining fuel amount.

*1: Models with tachometer

*2: Models with automatic transaxle and ABS

*3: Models with automatic transaxle




OPERATION


a.

Switching the Multi-information Display

i.

The multi-information display changes in the order shown below by pressing the ODO/TRIP DISP switch.

Y111219E02
4.302,1.271 4.698,1.458 4.698,1.458 4.958,1.458 true 4.979,1.375 5.25,1.583 0.271,0.208 10 false *1 3.188,1.948 3.771,2.156 0.583,0.208 10 false *3 (*A) 1.271,1.948 1.854,2.156 0.583,0.208 10 false *2 (*A) 1.26,2.979 1.844,3.188 0.583,0.208 10 false *4 3.177,2.969 3.76,3.177 0.583,0.208 10 false *5 5.115,2.969 5.698,3.177 0.583,0.208 10 false *6 5.115,4.281 5.698,4.49 0.583,0.208 10 false *7 5.146,5.594 5.729,5.802 0.583,0.208 10 false *8 3.188,5.594 3.771,5.802 0.583,0.208 10 false *9 1.26,4.271 1.896,4.479 0.635,0.208 10 false *11 (*B) 1.25,5.594 1.833,5.802 0.583,0.208 10 false *10

Text in Illustration
*A Models with Automatic Transaxle and ABS *B Models for Australia and G.C.C. Countries
*1 ODO/TRIP DISP Switch *2 Eco Driving Indicator Light Customizing Display: Eco On.
*3 Eco Driving Indicator Light Customizing Display: Eco Off. *4 Odometer Display
*5 Trip Meter A Display *6 Trip Meter B Display
*7 Instantaneous Fuel Consumption Display *8 Average Fuel Consumption After Refueling Display
*9 Drivable Distance Display *10 Average Vehicle Speed After Starting Display
*11 Dimming Mode Display (While Taillights ON) - -
V100135

Pressing the ODO/TRIP DISP switch
V100136

Pressing the ODO/TRIP DISP switch for approximately 5 seconds
V100137

Pressing the ODO/TRIP DISP switch for approximately 2 seconds - -



b.

Dimming Mode Display Function

i.

The brightness level of the combination meter assembly can be displayed on the multi-information display to adjust the meter luminance.


ii.

While the dimming mode is displayed, the brightness of the meter can be changed by pressing the ODO/TRIP DISP switch for 1 second or more. The brightness of the meter can be adjusted in 4 levels.

Y111221E02
4.302,1.323 4.698,1.51 4.698,1.51 4.958,1.51 true 4.99,1.448 5.26,1.656 0.271,0.208 10 false *1 1.135,3.094 1.406,3.302 0.271,0.208 10 false *2 2.729,3.094 3,3.302 0.271,0.208 10 false *3 4.271,3.094 4.542,3.302 0.271,0.208 10 false *4 5.865,3.094 6.135,3.302 0.271,0.208 10 false *5 0.479,1.938 0.76,2.146 0.281,0.208 10 false *a

Text in Illustration
*1 ODO/TRIP DISP Switch *2 100%
*3 75% *4 50%
*5 25% - -
*a Meter Brightness - -