Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2011.08–2015.06
NM19S0E _58 Vehicle Interior _051436 HEATING / AIR CONDITIONING _0247906 AIR CONDITIONING SYSTEM UN GENERAL/CONTROL/DETAILS F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

A Manual air conditioning system or automatic air conditioning system is used.


b.

A manual air conditioning system employing the boost vent, which is not equipped with the heater radiator unit sub-assembly that uses an engine coolant heater, has been provided on some models.



SPECIFICATION


a.

Performance

Destination Australia G.C.C. Countries General Countries
Air Conditioning Type Manual Automatic Manual Automatic Manual
Heater Heater Output W 4600 ← 4800*1 4800 4600*1
Air Flow Volume m3/h 280 ← 300*1 300 280*1
Power Consumption W 170 ← 200*1 200 170*1
Cooler Cooling Capacity W 4430 ← 4570 ← 4430*2 / 4450*3
Air Flow Volume m3/h 420 ← 465 ← 420*2 / 430*3
Power Consumption W 210 ← 245 ← 210*2 / 230*3

*1: Models without boost vent

*2: RHD models

*3: LHD models



b.

Ventilation and Heater Radiator Unit Sub-assembly

Destination Australia G.C.C. Countries General Countries
Heater Radiator Unit Sub-assembly Type Straight Flow Aluminum (SFA)-II Straight Flow Aluminum (SFA)-II*1 Straight Flow Aluminum (SFA)-II*1
Size: W x H x L mm (in.) 201.5 x 140 x 27 (7.9 x 5.5 x 1.1) 201.5 x 140 x 27 (7.9 x 5.5 x 1.1)*1 201.5 x 140 x 27 (7.9 x 5.5 x 1.1)*1
Fin Pitch mm (in.) 1.8 (0.07) 1.8 (0.07)*1 1.8 (0.07)*1
Blower with Fan Motor Sub-assembly Motor Type K62-12.5T K70-10T K62-11.5T*2 / K62-12.5T*3
Fan Type Semi Sirocco ← ←
Fan Size: Dia. x H mm (in.) 145 x 65 (5.7 x 2.6) ← ←

*1: Models without boost vent

*2: LHD models

*3: RHD models



c.

Air Conditioning

Destination Australia G.C.C. Countries General Countries
Cooler Condenser Assembly Type Multi-Flow (MF)-IV (Sub Cool) ← ←
Size: W x H x L mm (in.) 520 x 325.4 x 16 (20.5 x 12.8 x 0.6) 680 x 325.4 x 16 (26.8 x 12.8 x 0.6) 520 x 325.4 x 16 (20.5 x 12.8 x 0.6)
Fin Pitch mm (in.) 2.75 (0.1) 3.15 (0.1) 2.75 (0.1)
No. 1 Cooler Evaporator Sub-assembly Type Revolutionary super-Slim structure (RS) ← ←
Size: W x H x L mm (in.) 199.3 x 231 x 38 (7.8 x 9.1 x 1.5) ← ←
Fin Pitch mm (in.) 2.6 (0.1) ← ←
Compressor with Pulley Assembly Type 5TSE10C ← ←
Pulley Damper Limiter (DL) ← ←
Refrigerant Type HFC134a ← ←
Charge Volume g 360+/-30 380+/-30 360+/-30
Clean Air Filter High Efficiency Type ← ←



MAIN FEATURES


a.

The air conditioning system has the following features:

Item Outline
High Performance
·

Neural network control is used so passengers can control the air conditioning accurately for maximum comfort.*1

·

A high efficiency type clean air filter is used as the clean air filter.

·

The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.*1


Lightweight A bus connector (air conditioning harness assembly) with a built-in IC is used in a lightweight wire harness design with a reduced number of wires. The use of this connector means that pulse pattern type servo motors are used.*1
Compact
·

A semi-center location air conditioning unit in which the No. 1 cooler evaporator sub-assembly and heater radiator unit sub-assembly*2 are placed in the vehicle's longitudinal direction is used.

·

A blower motor with a built-in blower motor controller is used in a compact construction.*1


Others

The following parts are used to ensure high cooling or heating performance while realizing a compact and lightweight construction.

·

Revolutionary super-Slim structure (RS) type No. 1 cooler evaporator sub-assembly

·

Straight Flow Aluminum (SFA)-II type heater radiator unit sub-assembly*2

·

Multi-Flow (MF)-IV type cooler condenser assembly.

·

Continuously variable capacity type compressor with pulley assembly (5TSE10C type)




*1: Models with automatic air conditioning system

*2: Models without boost vent