Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.07–2017.01
NM19S0E _59 Vehicle Exterior _051441 LIGHTING (EXT) _0247912 LIGHTING SYSTEM UN GENERAL/CONTROL/DETAILS F

LIGHTING (EXT)  LIGHTING SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

Automatic Light Control System

Component Function
Main Body ECU (Multiplex Network Body ECU) Receives various signals and illuminates the headlights, taillights, clearance lights and license plate lights.
Headlight Dimmer Switch Assembly Light Control Switch Transmits an AUTO position signal to the main body ECU (multiplex network body ECU).
Automatic Light Control Sensor Detects the ambient light level.


b.

Light Automatic Turn-off System

Component Function
Main Body ECU (Multiplex Network Body ECU) Receives various signals, and turns off the exterior lights.
Front Door Courtesy Light Switch Assembly (for Driver) Detects whether driver's door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU).
Headlight Dimmer Switch Assembly Light Control Switch Transmits a light control position signal to the main body ECU (multiplex network body ECU).


c.

LED Headlight System

Component Function
Main Body ECU (Multiplex Network Body ECU) The main body ECU (multiplex network body ECU) receives the HEAD position signal from the light control switch and transmits a signal to the headlight relay.
Headlight Relay The headlight relay supplies power to the LED driver modules (Light Control ECU).
Headlight Assembly Light Emitting Diode (LED) The Light Emitting Diode (LED) light shines ahead over a broader area and further forward, increasing the area visible to the driver.
LED Driver Module (Light Control ECU) The LED driver module (Light Control ECU) keeps a constant level of direct current applied to the LED, achieving stable LED illumination.
Headlight Dimmer Switch Assembly Light Control Switch The light control switch transmits a HEAD position signal to the main body ECU (multiplex network body ECU).


d.

Automatic Headlight Beam Level Control System

Component Function
Headlight Leveling ECU Assembly
·

The headlight leveling ECU assembly detects changes of vehicle movement based on the rear height control sensor RH and vehicle speed signal.

·

The headlight leveling ECU assembly outputs control signals to the headlight leveling motors based on the detected value.

·

This ECU provides initial set control and a fail-safe function.


Headlight Assembly Headlight Leveling Motor
·

Based on the signals received from headlight leveling ECU assembly, each headlight leveling motor moves the projector unit in the headlight to vary its angle.

·

Each headlight leveling motor uses a stepper motor to precisely regulate the angle of the projector unit.


Main Body ECU (Multiplex Network Body ECU) The main body ECU (multiplex network body ECU) receives a HEAD position signal from the light control switch and transmits it to the headlight leveling ECU assembly.
Height Control Sensor Sub-assembly RR RH The rear height control sensor sub-assembly RH detects vehicle movement and transmits a signal to the headlight leveling ECU assembly.
Combination Meter Assembly The combination meter assembly transmits a vehicle speed signal to the headlight leveling ECU assembly.


e.

Light Reminder System

Component Function
Main Body ECU (Multiplex Network Body ECU) Outputs taillight illumination signals and driver's door open signals to the combination meter assembly.
Front Door Courtesy Light Switch Assembly (for Driver) Detects whether driver's door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU).
Combination Meter Assembly Receives taillight illumination signals and driver's door open signals from the main body ECU (multiplex network body ECU) when the ignition switch is turned off, and sounds the buzzer.



SYSTEM CONTROL


a.

LED Headlight System

i.

When the light control switch is turned on, the LED driver module (light control ECU) immediately turn on the LEDs (approximately 0.1 sec). In addition, by regulating the output currents flowing into the LEDs at the specified level, the LED driver module (light control ECU) prevent the glare of light due to voltage variation.


ii.

If malfunctions occur in the LED headlight system, an LED driver module (light control ECU) transmits fail signals to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives fail signals, it transmits signals to the combination meter, warning the driver.



b.

Automatic Headlight Beam Level Control System

i.

The height control sensor sub-assembly RR RH detects a change in height of the rear shaft in response to the weight applied to the rear of the vehicle when the vehicle is stopped and sends the change amount signal to the headlight leveling ECU. The headlight leveling ECU calculates the vehicle posture based on the change amount and controls the headlight beam level by operating the headlight leveling motor.

Y117511E03
2.125,2.594 2.031,2.594 2.031,2.594 1.719,1.906 true 3.021,0.271 3.385,0.271 3.385,0.271 2.531,1.781 true 0.26,0.167 2.969,0.594 2.708,0.427 10 false Height Control Sensor Sub-assembly RR RH 3.5,2.021 4.948,2.635 1.448,0.615 10 false Headlight Leveling ECU Assembly 5.469,2.125 7.042,2.479 1.573,0.354 10 false Headlight Leveling Motor 2.177,2.5 3.156,2.792 0.979,0.292 10 false Control Link 0.781,0.604 1.094,0.927 0.313,0.323 10 false Low 5.333,1.448 5.646,1.771 0.313,0.323 10 false Low 5.26,0.219 5.5,0.417 0.24,0.198 10 false (V) 5.156,0.396 5.302,0.594 0.146,0.198 10 false 5 5.156,1.25 5.302,1.448 0.146,0.198 10 false 0 6.104,1.458 6.25,1.656 0.146,0.198 10 false A 4.594,0.792 5.094,1.313 0.5,0.521 10 false Output Voltage 0.656,2.344 0.969,2.667 0.313,0.323 10 false High 6.563,1.448 6.875,1.771 0.313,0.323 10 false High 0.094,1.417 0.469,1.74 0.375,0.323 10 false Front 0.74,1.396 0.896,1.594 0.156,0.198 10 false A




FUNCTION


a.

Light Automatic Turn-off System

i.

The main body ECU (multiplex network body ECU) receives the light control switch signals, front door courtesy light switch assembly (driver side) on/off signal and ignition switch turned off signal, and turns off the exterior lights.

Light Control Switch Position Outline
TAIL, HEAD, AUTO While the lights (headlights, front fog lights and taillights) are turned on, this system automatically turns them off when the ignition switch is turned off and the driver's door is opened.


ii.

After the light automatic turn-off system was activated, when the ignition switch is shifted from ON to off while the light control switch (TAIL or HEAD) is turned on, the battery saving function turns off the headlights and taillights automatically in approximately 20 minutes. In addition, when one of the doors is opened from the closed status or closed from the opened status, the accumulated time is reset and the lights turn off in approximately 20 minutes after the door was opened/closed.


iii.

The light automatic turn-off system is controlled by the main body ECU (multiplex network body ECU).



b.

Automatic Headlight Beam Level Control System (Models with LED Headlight System)

i.

The automatic headlight beam level control system mainly consists of the headlight leveling ECU assembly, rear height control sensor sub-assembly RH and 2 headlight leveling motors. The headlight leveling ECU assembly controls the system.


ii.

The ECU detects the movement of the suspension from the height control sensor subassembly RR RH and the vehicle speed from the combination meter sub-assembly.


iii.

The ECU then controls the headlight leveling motor based on this information, in order to change the headlight reflector angle.


iv.

When the headlight leveling ECU assembly detects that the vehicle is stopped and the ignition switch is ON, the ECU executes the initial setting of the stepper motors.



c.

Light Reminder System

i.

The light reminder system warns the driver using a buzzer when the meter ECU inside the combination meter assembly receives the driver's door courtesy light switch signal via the main body ECU (multiplex network body ECU) and the ignition switch is turned off and the door is opened with the taillights kept on. The buzzer is located inside the combination meter assembly.

Light Control Switch Position Ignition Switch Door Buzzer
TAIL, HEAD Switch off Open Sounds
Closed -




CONSTRUCTION


a.

LED Driver Module

i.

The LED driver modules are placed beneath the headlights and this supplies a constant voltage to the low beams and reduces the changes in the energization current.

Y150772E02
1.417,0.646 1.521,0.646 1.521,0.646 3.385,1.75 true 1.271,0.573 1.573,0.833 0.302,0.26 10 false *1

*1 LED Driver Module - -




FAIL-SAFE


a.

LED Headlight System

i.

The LED driver module (light control ECU) executes the fail-safe actions listed below in accordance with the problem that has been detected.

Problem Outline
Abnormal Output (Open Circuit or Short Circuit) If an abnormal condition (open or short) occurs in the voltage that is output by the LED driver module (light control ECU), the LED driver module (light control ECU) stops illuminating the headlights and will maintain this state until the power is reinstated. Power is reinstated by turning the headlight dimmer switch assembly (light control switch) from off to on.
Abnormal input voltage (High input voltage) When the headlights are on, if the LED driver module (light control ECU) receives a voltage of more than 17 V, it will turn the headlights off. When the input voltage resumes to the normal operating voltage range, the LED driver module will turn the headlights on.
Abnormal input voltage (Low input voltage) When the headlights are on, if the LED driver module (light control ECU) detects that the input voltage has decreased to 6 to 10V, it will dim the headlights. When the input voltage resumes to a normal operating voltage range, the LED driver module will return the headlight brightness to the normal brightness.
If the LED driver module receives a voltage of less than 6 V, it will turn the headlights off. When the power voltage resumes to more than 8.5 V, the LED driver module will turn the headlights on.



b.

Automatic Headlight Beam Level Control System

i.

If an abnormal condition such as those listed below has been detected, the headlight leveling ECU operates in the fail-safe mode.

Problem Outline
Power Supply Voltage Malfunction Holds the beam at the position of the headlight leveling motor when the abnormality has been detected.
Rear Height Control Sensor Sub-assembly Data Error During Initialization
Vehicle Model Code Inconsistent
Rear Height Control Sensor Sub-assembly Power Supply Malfunction
Rear Height Control Sensor Sub-assembly Signal Malfunction




DIAGNOSIS


a.

LED Headlight System

i.

If the main body ECU (multiplex network body ECU) detects a malfunction in the LED headlight system, the combination meter assembly flashes the master warning light and indicates the warning message on the multi-information display. At the same time, the Diagnostic Trouble Code (DTC) is stored in memory. The DTC can be read using the intelligent tester. For details, refer to the Repair Manual.



b.

Automatic Headlight Beam Level Control System

i.

When the headlight leveling ECU assembly detects malfunctions in the automatic headlight beam level control system, DTCs are stored in memory.


ii.

The DTCs can be read using the intelligent tester. For details, refer to the Repair Manual.