Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.01–2018.06
NM19S0E _58 Vehicle Interior _063154 PRE-CRASH SAFETY _0307655 PRE-CRASH SAFETY SYSTEM UN GENERAL/CONTROL/DETAILS F

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Item Function
Pre-crash Safety City Sensor
·

Monocular Camera Sensor

·

Laser Sensor

·

Pre-crash Safety City Sensor ECU


·

Receives information from the monocular camera sensor and laser sensor regarding vehicles ahead, and performs pre-crash safety system control.

·

When performing pre-crash safety system control, it also sends request signals to the combination meter assembly to display applicable messages and sound the buzzer.

·

When pre-crash brake or pre-crash brake assist are operating, it sends signals to the skid control ECU requesting vehicle speed reduction.

·

Sounds the buzzer during warning operation.


Brake Actuator Assembly
·

Skid Control ECU

·

Pump Motor

·

Master Cylinder Pressure Sensor


·

Based on the pre-crash safety city sensor signal, sends control signals to the brake actuator to operate the brakes.

·

Sends vehicle speed signal, stop light switch signal and master cylinder pressure signal to the pre-crash safety city sensor.

·

Detects brake control signals and sends signals to the stop light switch assembly.

·

Receives an operation signal from the skid control ECU and generates hydraulic pressure for brake control.

·

Detects the master cylinder pressure and transmits a signal to the skid control ECU.


Combination Meter Assembly
·

PCS Warning Light

·

PCS Activation Indicator

·

Multi-information Display

·

Buzzer


·

During warning operation, flashes the PCS activation indicator to warn the driver.

·

When the pre-crash safety system is OFF, the PCS warning light illuminates.

·

When the pre-crash safety system is not available due to certain reasons, the PCS warning light illuminates.

·

During system malfunction, flashes the PCS warning light and sounds the buzzer to warn the driver.

·

Based on pre-crash system cancel switch assembly operation, displays pre-crash safety system ON/OFF and warning timing.


ECM
·

Sends the accelerator pedal opening angle signal and shift position signal*1 to the pre-crash safety city sensor.

·

Controls engine output based on the signal from the pre-crash safety city sensor.


Airbag Sensor Assembly
·

Yaw Rate Sensor

·

Acceleration Sensor


Detects the yaw rate (rotational movement) and front/back/left/right acceleration of the vehicle body, and sends the signal to the pre-crash safety city sensor.
Spiral Cable with Sensor Sub-assembly
·

Steering Angle Sensor


Detects the steering and direction, and sends the signal to the pre-crash safety city sensor.
Pre-crash Safety City Buzzer Sounds during warning operation to warn the driver.
Pre-crash System Cancel Switch Assembly By operating the switch, the pre-crash safety system can be turned ON/OFF and the warning timing can be changed.
VSC OFF Switch When the VSC OFF switch is operated to turn the brake system to VSC OFF mode, pre-crash brake and pre-crash brake assist operation is turned OFF (only the pre-crash warning function can operate).
Speed Sensors Detect the wheel speeds, and send the signals to the skid control ECU.
Stop Light Switch Assembly
·

Detects that the brake pedal has been depressed, and sends the signal to the skid control ECU.

·

Illuminates the stop light based on signals from the skid control ECU.


Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression amount and sends the signal to the ECM.
Park/Neutral Position Switch Assembly*1 Detects the shift position and sends the signal to the ECM.
Back-up Light Switch Assembly*2 Detects the reverse position and sends the signal to the pre-crash safety city sensor.

*1: Models with automatic transaxle

*2: Models with manual transaxle


FUNCTION


a.

The pre-crash safety system uses the monocular camera sensor and laser sensor inside the pre-crash safety city sensor to determine if there is a risk of this vehicle colliding with the preceding vehicle.


b.

When the probability of a collision is high, the pre-crash safety system sends a warning via the meter display and buzzer, and performs brake assist control. Additionally, when the probability of a collision is extremely high, the system performs brake control in order to help reduce the impact force if a collision occurs.


c.

During brake control by the pre-crash safety system, the skid control ECU illuminates the stop light in order to inform any following vehicles that this vehicle is braking.

Y208321C02
1.365,1.125 1.167,0.25 1.167,0.25 1,0.25 true 2.281,1.125 2.083,0.25 2.083,0.25 1.917,0.25 true 3.167,1.167 2.969,0.26 2.969,0.26 2.802,0.26 true 0.781,0.146 1.094,0.344 0.313,0.198 10 false *a 1.729,0.156 2.042,0.354 0.313,0.198 10 false *b 2.604,0.156 2.917,0.354 0.313,0.198 10 false *c 0.271,2.417 0.583,2.615 0.313,0.198 10 false *d
*a This Vehicle *b Probability of collision extremely high
*c Preceding Vehicle *d The illustrations shown are examples only.
V100144

Laser Sensor Detection Area
V100145

Monocular Camera Sensor Image Recognition Area




OPERATING CONDITION


a.

The pre-crash safety system is enabled and determines that the possibility of a frontal collision with a vehicle is high.

Pre-crash Safety System Operating Conditions
Pre-crash Warning
·

Vehicle speed is approximately 15 to 140 km/h (10 to 86 mph).

·

The relative speed between your vehicle and the vehicle ahead is greater than approximately 15 km/h (10 mph).


Pre-crash Brake Assist
·

Vehicle speed is approximately 30 to 80 km/h (19 to 49 mph).

·

The relative speed between your vehicle and the vehicle ahead is greater than approximately 30 km/h (19 mph).

·

The brake pedal is being depressed.


Pre-crash Brake
·

Vehicle speed is approximately 10 to 80 km/h (7 to 49 mph).

·

The relative speed between your vehicle and the vehicle ahead is greater than approximately 10 km/h (7 mph).



HINT:

In case of the following, the system will not operate:


·

Steering Sensor zero point calibration has not been completed

·

If VSC is disabled (only the pre-crash warning function will be operational)

·

If the PCS warning light is flashing or illuminated

·

If the shift position is in R



b.

If either of the following situations occur while the pre-crash brake function is operating, it will be canceled:

·

The accelerator pedal is depressed strongly

·

The steering wheel is turned sharply or abruptly



c.

If the vehicle is stopped by the operation of the pre-crash brake function, the operation of the pre-crash brake function will be canceled after the vehicle has been stopped for approximately 2 seconds.


d.

When the driver is depressing the brake pedal, the system judges that the driver is preparing to avoid a collision, so the system may delay the pre-crash brake activation timing.


e.

During the following, the driver operations takes precedence and the system may not operate:

·

The accelerator pedal is depressed strongly

·

The steering wheel is turned sharply or abruptly



f.

In some situations such as the following, the system may determine that there is a possibility of a frontal collision and operate:

·

When passing a vehicle in an oncoming lane that is stopped to make a left/right turn

Y191511

·

When passing an oncoming vehicle while making a left/right turn

Y191512

·

When driving on a road where relative location to vehicle ahead in an adjacent lane may change, such as on a winding road

Y191513

·

When rapidly closing on a preceding vehicle

Y191514

·

If the front of the vehicle is raised or lowered, such as when the road surface is uneven or undulating

·

When passing extremely close to a vehicle or structural object

Y191515

·

When there is a vehicle or object by the roadside at the entrance of a curve

Y191516

·

When driving on a narrow path surrounded by a structure, such as in a tunnel or on an iron bridge

·

When there is a reflective object (manhole cover, steel plate, etc.), steps, dip, or a protrusion on the road surface or roadside

Y191517

·

When passing through a place with a low structure above the road (low ceiling, traffic sign, etc.)

Y191518

·

When there is a structural object (overpass, traffic sign, billboard, street light, etc.) at the top of an uphill road

Y192585

·

When rapidly closing on an electric toll gate barrier, parking area barrier, or other barrier that opens and closes

Y192586

·

When using an automatic car wash

·

When approaching a low hanging object that may contact the vehicle, such as a banner, tree branches or thick grass

Y192587

·

When the vehicle is hit by water, snow, dust, etc. from a vehicle ahead

Y192588

·

When driving through steam or smoke

Y192589

·

When there are patterns or paint on the road or a wall that may be mistaken for a vehicle

·

When the front part of the vehicle is raised or lowered

Y192590

·

When the pre-crash safety city sensor is misaligned due to a strong impact being applied to the pre-crash safety city sensor, etc.

Y192591

·

When the vehicle is being parked in a place where there is a low hanging object at the height of the pre-crash safety city sensor

Y192592

·

When the windshield glass is covered with raindrops, etc.

Y192593



g.

In some situations such as the following, a vehicle may not be detected by the pre-crash safety city sensor, preventing the system from operating properly:

·

If an oncoming vehicle is approaching your vehicle

·

When approaching the side or front of a vehicle

·

If a preceding vehicle has a small rear end, such as an unloaded truck

·

If a preceding vehicle has a low rear end, such as a low bed trailer

Y192594

·

If a vehicle ahead is carrying a load which protrudes past its rear bumper

·

If a vehicle ahead has extremely high ground clearance

Y192595

·

If a vehicle ahead is irregularly shaped, such as a tractor or side car

·

If the sun or other light is shining directly on a vehicle ahead

·

If a vehicle cuts in front of your vehicle or emerges from beside a vehicle

Y192596

·

If a vehicle ahead makes an abrupt maneuver (such as sudden swerving, acceleration or deceleration)

·

When suddenly cutting behind a preceding vehicle

·

When a vehicle ahead is not directly in front of your vehicle

Y192597

·

When driving in inclement weather such as heavy rain, fog, snow or a sand storm

Y192598

·

When the vehicle is hit by water, snow, dust, etc. from a vehicle ahead

·

When driving through steam or smoke that may obscure vehicles ahead

·

When driving in a place where the surrounding brightness changes suddenly, such as at the entrance or exit of a tunnel

·

When a very bright light, such as the sun or the headlights of oncoming traffic, shines directly into the pre-crash safety city sensor

Y192599

·

When the surrounding area is dim, such as at dawn or dusk, or while at night or in a tunnel

Y192601

·

While driving on a curve and for a certain amount of time after driving on a curve

·

If your vehicle is skidding

Y192600

·

When the front part of the vehicle is raised or lowered

Y192590

·

If the wheels are misaligned

·

If a wiper blade is blocking the pre-crash safety city sensor

·

The vehicle is wobbling

·

The vehicle is being driven at extremely high speeds

·

When driving on roads with sharp bends or uneven surfaces

·

When a preceding vehicle is a poor reflector of laser

·

When the pre-crash safety city sensor is misaligned due to a strong impact being applied to the pre-crash safety city sensor, etc.

Y192591



h.

In some situations such as the following, sufficient braking force may not be obtained, preventing the system from performing properly:

·

If the braking functions cannot operate to their full extent, such as when the brake parts are extremely cold, extremely hot, or wet

·

If the vehicle is not properly maintained (brakes or tires are excessively worn, improper tire inflation pressure, etc.)

·

When the vehicle is being driven on a gravel road or other slippery surface



i.

If the PCS warning light flashes or illuminates, the pre-crash safety system may be temporarily unavailable or there may be a malfunction in the system.

i.

In the following situations, the PCS warning light will turn off and the system will become operational when normal operating conditions return:

·

When the area around the pre-crash safety city sensor is hot, such as in the sun

·

When the windshield glass is fogged up, or covered with condensation or ice

·

When the pre-crash safety city sensor or the area around the sensor is cold, such as in an extremely cold environment

·

If the area in front of the pre-crash safety city sensor is obstructed, such as when the hood is open



ii.

If the PCS warning light continues to flash, the system may be malfunctioning.



j.

If VSC is disabled, the pre-crash brake assist and pre-crash brake functions are also disabled. However, the pre-crash warning function will still operate.



SYSTEM CONTROL


a.

The pre-crash safety city sensor sends and receives signals to and from various ECUs, sensors and switches to perform pre-crash safety system control.

Pre-crash Safety System Control List
Control Function
Pre-crash Brake
·

When the system determines that there is a high possibility of a collision, the PCS activation indicator in the combination meter assembly flashes and the buzzer sounds to warn the driver.

·

When the system determines that there is an extremely high probability of a collision, the brake is applied to reduce vehicle speed even if the driver has not depressed the brake pedal.


Pre-crash Brake Assist When the system determines that there is a high probability of a collision, brake hydraulic pressure assistance is performed, improving brake effectiveness when the brake pedal is depressed. Also, if the brake pedal is depressed before the system determines there is a high possibility of a collision, once the determination is made, brake hydraulic pressure assistance is immediately performed.


b.

Pre-crash Brake

i.

When the pre-crash safety city sensor detects an object such as a vehicle or road structure in front of the vehicle and determines that the probability of a collision is high, the PCS activation indicator in the combination meter assembly flashes and the buzzer sounds to warn the driver.


ii.

When the system determines that there is an extremely high probability of a collision, pre-crash brake control activates.

Y191495E03
0.74,0.365 1.719,1.01 0.979,0.646 10 false High probability of collision* 2.51,0.385 3.854,0.979 1.344,0.594 10 false Extremely high probability of collision 5.646,0.427 6.188,1.031 0.542,0.604 10 false Collision 0.552,1.51 1.042,2.281 0.49,0.771 10 false Normal Driving 0.365,1.083 0.75,1.313 0.385,0.229 10 false Time 1.698,1.646 5.865,2.135 4.167,0.49 10 false Warning Control (PCS activation indicator flashing and Buzzer) 0.042,3.688 0.542,4.313 0.5,0.625 10 false Vehicle Speed 6.063,3.719 7.115,4.344 1.052,0.625 10 false Speed Reduction Effect 3.656,2.74 5.396,3.146 1.74,0.406 10 false Collision Impact Reduction 0.167,4.927 6.948,5.74 6.781,0.813 10 false *: Warning timing can be selected as "Far", "Middle" or "Near" by operating the pre-crash system cancel switch assembly.



c.

Pre-crash Brake Assist

i.

While the pre-crash safety city sensor has determined that there is a high probability of a collision, brake hydraulic pressure assistance is performed when the driver depresses the brake pedal. Also, the amount of brake hydraulic pressure assistance increases further when the system determines that there is an extremely high probability of a collision.

Y191496E03
0.208,0.896 0.583,1.219 0.375,0.323 10 false Time 1.052,0.24 2.229,0.979 1.177,0.74 10 false High probability of collision 2.563,0.25 3.333,0.927 0.771,0.677 10 false Brake pedal depressed 3.635,0.25 4.594,1.01 0.958,0.76 10 false Extremely high probability of collision 5.135,0.219 5.75,0.854 0.615,0.635 10 false Collision 0.865,1.49 1.833,2.125 0.969,0.635 10 false Normal Driving 2,1.469 2.625,2.26 0.625,0.792 10 false Standby Condition 2.938,1.469 3.917,2.26 0.979,0.792 10 false Brake Pressure Boost Assist 4.469,1.448 5.104,3.083 0.635,1.635 10 false Pressure Boost Assist amount increased 2.938,3.208 4.396,4.26 1.458,1.052 10 false Pressure Boost Assist starts as soon as brake pedal depressed 0.073,4.063 0.688,5.26 0.615,1.198 10 false Brake Hydraulic Pressure 0.125,5.729 0.688,6.365 0.563,0.635 10 false Vehicle Speed 2.99,6.135 4.073,7.135 1.083,1 10 false Pre-crash Brake Assist 5.219,4.885 7.063,5.188 1.844,0.302 10 false Normal Brake Pressure 5.24,5.896 6.26,6.24 1.021,0.344 10 false Normal Braking 5.25,6.469 6.938,7.51 1.688,1.042 10 false Vehicle Speed reduction amount when probability of collision is extremely high 5.208,4.458 7.135,4.833 1.927,0.375 10 false Effect of Pressure Boost Assist 5.229,3.198 7.115,4.198 1.885,1 10 false Pressure Boost Assist amount when probability of collision is extremely high


ii.

When the driver begins to depress the brake pedal before the system determines that there is a high probability of a collision, once the determination is then made, brake hydraulic pressure assistance is immediately performed. This hydraulic pressure assistance is also applied in response to the amount the brake pedal was depressed before the start of assistance.

Y191497E03
0.167,1.313 0.521,1.625 0.354,0.313 10 false Time 2.177,0.552 3.583,1.25 1.406,0.698 10 false Even higher probability of collision 0.771,0.573 1.906,1.042 1.135,0.469 10 false Brake Depressed 5.156,0.552 5.708,0.854 0.552,0.302 10 false Collision 0.885,1.719 1.354,2.292 0.469,0.573 10 false Normal Driving 1.698,1.719 2.198,2.302 0.5,0.583 10 false Normal Braking 2.854,1.771 4.688,2.24 1.833,0.469 10 false Brake Pressure Boost Assist 5.458,2.302 7.135,3.167 1.677,0.865 10 false Pressure Boost Assist amount when probability of collision is extremely high 5.469,3.208 7.01,3.823 1.542,0.615 10 false Effect of Pressure Boost Assist 5.448,3.865 7,4.146 1.552,0.281 10 false Normal Brake Pressure 5.458,4.688 6.521,4.969 1.063,0.281 10 false Normal Braking 5.438,5.271 7.094,6.177 1.656,0.906 10 false Vehicle Speed reduction amount when probability of collision is extremely high 3.052,5.208 4.625,5.698 1.573,0.49 10 false Pre-crash Brake Assist 2.281,2.385 4.135,3.26 1.854,0.875 10 false Pressure Boost Assist begins as soon as signal received 0.042,3.427 0.615,4.177 0.573,0.75 10 false Brake Pressure 0.083,5.125 0.583,5.771 0.5,0.646 10 false Vehicle Speed




CONSTRUCTION


a.

Pre-crash Safety City Sensor

i.

The pre-crash safety city sensor is installed on the inside of the windshield glass, at the top center. It uses its built-in monocular camera sensor to acquire a video of the area in front of the vehicle, uses its built-in laser sensor to detect other vehicles in front of this vehicle, and uses both detection results to determine whether there is a preceding vehicle and how far away it is, enhancing high recognition performance and reliability.

Y210643C01
5.656,1.417 5.99,0.583 5.99,0.583 6.156,0.583 true 2.167,1.417 2.5,0.917 2.5,0.917 2.667,0.917 true 2,1.333 2.438,0.667 2.438,0.667 2.604,0.667 true 1.792,1.198 1.583,0.75 1.583,0.75 1.417,0.75 true 1.458,1.865 1.25,2.167 1.25,2.167 1.083,2.167 true 1.229,0.656 1.542,0.813 0.313,0.156 10 false *a 2.667,0.583 2.979,0.74 0.313,0.156 10 false *b 0.896,2.073 1.208,2.229 0.313,0.156 10 false *c 2.792,6.854 3.104,7.01 0.313,0.156 10 false *d 3.823,7.385 4.135,7.542 0.313,0.156 10 false *e 2.729,0.833 2.969,1.052 0.24,0.219 10 false *b 6.208,0.49 6.448,0.708 0.24,0.219 10 false *1
*1 Pre-crash Safety City Sensor
·

Pre-crash Safety City Sensor ECU


- -
*a Monocular Camera Sensor *b Laser Sensor Receiver
*c Laser Sensor Emitter *d Laser Sensor Detection Area
*e Monocular Camera Sensor Image Processing Area - -





OPERATION


a.

Pre-crash Safety System Display

i.

The Pre-crash safety system uses the PCS warning light, multi-information display, PCS activation indicator and buzzer in the combination meter assembly to display warnings and control status information.

Y197953C01
1.073,1.25 1.24,1.25 1.24,1.25 2.083,2.417 true 1.771,3.406 1.938,3.406 1.938,3.406 2.5,2.708 true 3,0.25 3.167,0.25 3.167,0.25 3.583,0.771 true 3.833,2.75 4.167,3.333 4.167,3.333 4.333,3.333 true 2.823,0.177 3.135,0.375 0.313,0.198 10 false *1 4.438,3.25 4.75,3.448 0.313,0.198 10 false *a 0.771,1.167 1.083,1.365 0.313,0.198 10 false *b 1.5,3.333 1.813,3.531 0.313,0.198 10 false *c
*1 Combination Meter Assembly - -
*a Multi-information Display *b PCS Warning Light
*c PCS Activation Indicator - -




b.

Pre-crash Safety System Operating Status Display

i.

When the pre-crash safety city sensor, which controls the pre-crash safety system, judges that the possibility of a collision is high, it sends a display request signal to the combination meter, causing the PCS activation indicator to flash and the buzzer to sound.

Multi-information Display PCS Warning Light PCS Activation Indicator Buzzer
- - Flashes Sounds Intermittently



c.

Indicator Display when Pre-crash Safety System is OFF

i.

Operating the pre-crash system cancel switch assembly allows the pre-crash safety system to be turned ON and OFF. When the system is turned OFF, the PCS warning light illuminates.

Pre-crash Safety System Multi-information Display PCS Warning Light PCS Activation Indicator Buzzer
ON - - - -
OFF PCS OFF* Illuminates - -

HINT:

*: Displayed for approximately 6 seconds



ii.

When VSC operation has been stopped by VSC OFF switch operation, the PCS warning light and VSC OFF indicator light illuminate.

Multi-information Display PCS Warning Light PCS Activation Indicator VSC OFF Indicator Light
- Illuminates - Illuminates



d.

Pre-crash Safety System Warning Display

i.

When the pre-crash safety city sensor detects a system malfunction, it sends a warning display request signal to the combination meter assembly, which flashes or illuminates the PCS warning light. If the malfunction is judged to be a system failure, the buzzer sounds.

Displayed Status Possible Conditions PCS Warning Light Buzzer
System Failure System Failure Flashes Sounds once
System Voltage Abnormal Auxiliary battery voltage has decreased, etc. Illuminates -
Pre-crash Safety City Sensor Temperature Abnormal Operating temperature range of pre-crash safety city sensor exceeded Illuminates -
Pre-crash Safety City Sensor Dirty Windshield glass is dirty, frosted or fogged up Illuminates -



e.

Pre-crash System Cancel Switch Assembly

i.

A pre-crash system cancel switch assembly is provided to turn the pre-crash safety system ON/OFF and switch between different warning timings.


ii.

When the pre-crash safety system is ON, briefly pressing the pre-crash system cancel switch assembly displays the warning timing. While the warning timing is being displayed, each additional press of the pre-crash system cancel switch assembly changes the warning timing displayed on the multi-information display in the order far-middle-near. This enables the pre-crash safety system to be switched between 3 levels of sensitivity.


iii.

When the pre-crash safety system is ON, pressing and holding the pre-crash system cancel switch assembly for approximately 3 seconds allows the pre-crash safety system to be cancelled. At this time, in the combination meter assembly the PCS warning light illuminates and "PCS OFF" is displayed on the multi-information display. Also, while the pre-crash safety system is cancelled, briefly pressing the pre-crash system cancel switch assembly can be turned ON again.

Pre-crash Safety System Warning Timing Change Sequence by Pre-crash System Cancel Switch Assembly Operation
Y192617E06
2.875,2.333 4.448,2.979 1.573,0.646 10 false Pre-crash safety System ON 0.146,3.719 1.365,4.406 1.219,0.688 10 false PCS Warning Light illuminates 5.75,2.438 7,3.844 1.25,1.406 10 false Warning Timing Display (Currently selected warning timing is displayed) 0.146,5.333 1.76,5.656 1.615,0.323 10 false Warning Timing Selection 0.177,1.729 1.417,2.771 1.24,1.042 10 false Displayed on Multi-information Display 0.604,8.135 5.406,8.438 4.802,0.302 10 false : Pre-crash system cancel switch assembly pressed briefly 0.604,8.5 5.813,8.823 5.208,0.323 10 false : Pre-crash system cancel switch assembly pressed and held for 3 seconds 2.844,6.115 4.365,6.438 1.521,0.323 10 false Middle (Default setting) 0.427,6.115 1.865,6.438 1.438,0.323 10 false Far (Timing is earlier) 5.375,6.115 6.75,6.438 1.375,0.323 10 false Near (Timing is later) 3.75,4.656 5.302,5.01 1.552,0.354 10 false Displayed for 6 seconds 3.771,1.271 5.302,1.625 1.531,0.354 10 false Ignition Switch ON 4.75,3.417 5.594,4.156 0.844,0.74 10 false Displayed for 6 seconds 0.042,4.552 1.656,5.146 1.615,0.594 10 false Pre-crash Safety System OFF 2.896,3.323 4.417,4.031 1.521,0.708 10 false PCS Warning Light turns off