Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › from 2017.01
NM19S0E _54 Brake _051417 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0247884 BRAKE CONTROL SYSTEM UN GENERAL/CONTROL/DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function

*: Models with Toyota Safety Sense

Brake Actuator Assembly Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends brake control signals to the brake actuator.
Solenoid Valve Changes the fluid path based on the signals from the skid control ECU during the operation of the ABS with EBD, Brake Assist, TRC and VSC, in order to control the fluid pressure that is applied to the wheel cylinders.
Master Cylinder Cut Solenoid Valve
Pump Motor Drives the pumps inside the brake actuator.
Solenoid Relay Supplies power to the solenoid valves.
Motor Relay Supplies power to the motor.
Motor Failsafe Relay Cuts the power to the motor when the motor relay malfunctions.
Master Cylinder Pressure Sensor Assembled in the brake actuator, detects the master cylinder pressure.
Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Airbag Sensor Assembly Yaw Rate and Deceleration Sensor Detects the yaw rate and the longitudinal and lateral acceleration and deceleration of the vehicle body.
Front Speed Sensor RH Detect the wheel speed of each of the 4 wheels.
Front Speed Sensor LH
Rear Speed Sensor RH (Skid Control Sensor Wire RH)
Rear Speed Sensor LH (Skid Control Sensor Wire LH)
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Assembly Detects when the parking brake lever is pulled up.
Brake Fluid Level Warning Switch Detects the brake fluid level.
VSC OFF Switch Enables the driver to select the "Normal Mode", "TRC-OFF Mode" or "VSC-OFF Mode".
Main Body ECU (Multiplex Network Body ECU) Transmits the parking brake switch signal to the skid control ECU.
ECM
·

Sends the throttle position signal, accelerator pedal position signal engine speed signal to the skid control ECU.

·

Based on the signals receives from the skid control ECU, controls the engine output.


Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Brake Warning Light
·

Lights up together with ABS warning light to alert the driver when the skid control ECU detects the malfunction not only in the ABS but also in the EBD.

·

Lights up to alert the driver when the brake fluid level is low.


Parking Brake Warning Light Lights up to inform the driver when the parking brake lever is pulled up.
Slip Indicator Light
·

Lights up to alert the driver in the event of malfunction of the TRC, VSC or the Hill-start Assist Control.

·

Blinks to inform the driver when the TRC or VSC operates.


TRC OFF Indicator Light Lights up to inform the driver of "TRC-OFF mode" or "VSC-OFF mode" being selected.
VSC OFF Indicator Light Lights up to inform the driver of "VSC-OFF mode" being selected.
Pre-crash Safety City Sensor* Judges whether collision is imminent, and makes a request for brake control to the skid control ECU.
Hazard Warning Switch Transmits a hazard warning light on/off request to the combination meter assembly.


OPERATING CONDITION


a.

Emergency Brake Signal

i.

Emergency brake signal operating conditions are as shown in the following table.

Activating Conditions When all of the following conditions are met, the emergency brake signal starts operating.
·

Vehicle speed is over 55 km/h (35 mph).

·

Driver is depressing the brake pedal.

·

Emergency braking is detected from the vehicle deceleration.


Deactivating Conditions When any of the following conditions is met, emergency brake signal stops operating.
·

Driver has released the brake pedal.

·

Emergency braking is no longer detected from the vehicle deceleration.

·

Driver has pressed the hazard warning switch.






SYSTEM CONTROL


a.

Control List

i.

The brake control system have the following controls:

Control Outline

*: Models with Toyota Safety Sense

Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle stability.
Brake Assist The primary purpose of the Brake Assist is to provide an auxiliary brake force to assist the driver who cannot generate a large brake force during emergency braking, thus helping draw the vehicle's brake performance.
Traction Control (TRC) The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Vehicle Stability Control (VSC) The VSC helps prevent the vehicle from slipping sideway as a result of strong front wheel skid or strong rear wheel skid during cornering.
Engine Output Control during TRC or VSC Operation Transmits an engine output control signal from the skid control ECU to the ECM to limit the engine output while the TRC or VSC is being activated.
Hill-start Assist Control When starting uphill, this control maintains the brake hydraulic pressure to the 4 wheels, in order to momentarily prevent the vehicle from descending backward.
Brake Control (Pre-crash Safety System Operating)* When the pre-crash safety city sensor determines the collision is imminent, the skid control ECU activates the pre-crash brake assist or the pre-crash brake according to the signal from the pre-crash safety city sensor.
Emergency Brake Signal In the case of emergency braking, the emergency brake signal flashes the hazard warning lights to alert the drivers in following vehicles.



b.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X106018E01
5.057,0.784 5.309,0.960 0.252,0.175 10 *A 5.057,1.646 5.309,1.822 0.252,0.175 10 *B 3.712,2.464 3.964,2.639 0.252,0.175 10 *a

Text in Illustration
*A With ABS *B Without ABS
*a Brake Operation - -



c.

Electronic Brake Force Distribution (EBD)

i.

The distribution of the brake force, which was performed mechanically in the past, is now performed under electrical control of the skid control ECU, which controls the braking force in accordance with the vehicle's driving conditions.


ii.

If the brakes are applied while the vehicle is moving straight forward, the transfer of the load reduces the weight that is applied to the rear wheels. The skid control ECU determines this condition by way of the signals from the speed sensor, and the brake actuator regulates the distribution of the brake force of the rear wheels to optimally control. For example, the amount of the brake force that is applied to the rear wheels during braking varies depending on whether the vehicle is carrying load or not. The amount of the brake force that is applied to the rear wheels also varies in accordance with the extent of the deceleration. Thus, the distribution of the brake force to the rear is optimally controlled in order to effectively utilize the braking force of the rear wheels under these conditions.

X100697E01
1.948,1.719 1.781,1.719 1.781,1.719 1.781,2.563 true 4.917,1.406 4.74,1.406 4.74,1.406 4.74,2.375 true 2.406,2.635 2.229,2.635 2.229,2.635 2.063,2.49 true 5.417,2.604 5.24,2.604 5.24,2.604 5.073,2.458 true 0.594,2.135 1.344,2.542 0.75,0.406 10 Rear Brake Force 3.583,2.135 4.344,2.781 0.76,0.646 10 Rear Brake Force 1.99,1.635 3.125,2.031 1.135,0.396 10 Ideal Brake Force Distribution 4.958,1.323 6.104,1.708 1.146,0.385 10 Ideal Brake Force Distribution 2.438,2.542 3.229,2.854 0.792,0.313 10 EBD Control 5.448,2.531 6.24,2.844 0.792,0.313 10 EBD Control 1.729,2.917 2.885,3.24 1.156,0.323 10 Front Brake Force 4.74,2.917 5.896,3.24 1.156,0.323 10 Front Brake Force 1.667,3.281 3.01,3.625 1.344,0.344 10 Without Load in Rear 4.781,3.292 5.927,3.625 1.146,0.333 10 With Load in Rear


iii.

When the brakes are applied while the vehicle is cornering, the load that is applied to the inner wheel decreases as the load to the outer wheel increases. The skid control ECU determines this condition by way of the signals from the speed sensor, and the brake actuator regulates the brake force in order to optimally control the distribution of the brake force to the inner wheel and outer wheel.

X106020E04
4.156,0.479 4.469,0.156 4.469,0.156 4.615,0.156 false 4.656,0.063 4.906,0.24 0.25,0.177 10 false *a

Text in Illustration
*a Control Moment - -
V100135

Brake Force - -



d.

Brake Assist

i.

With Brake Assist, based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the amount the brake pedal is applied and the speed at which it is depressed to determine if the driver is attempting emergency braking. If the skid control ECU determines that the driver is attempting emergency braking, the Brake Assist function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

X100121E01
3.404,0.081 4.790,0.327 1.386,0.246 10 Skid Control ECU 3.513,0.466 5.969,0.941 2.456,0.475 10 The fluid pressure is increased by the skid control ECU 1.918,0.377 3.012,1.032 1.093,0.656 10 Master Cylinder Pressure Sensor Signal 1.566,4.011 2.168,4.493 0.603,0.482 10 Braking Force 4.41,4.032 6.192,4.486 1.782,0.454 10 With Brake Assist 4.41,4.704 6.192,5.089 1.782,0.385 10 Without Brake Assist 5.13,5.293 5.517,5.476 0.387,0.184 10 Time



e.

Traction Control (TRC)

i.

If the driver depresses the accelerator pedal aggressively when initially accelerating or when accelerating on a slippery surface, the drive wheels could slip due to the excessive amount of torque that is generated. By applying hydraulic brake control to the drive wheels and regulating the throttle to control the engine output, the TRC helps minimize the slippage of the drive wheels, thus generating the drive force that is appropriate for the road surface conditions.


ii.

For example, a comparison may be made between two vehicles, one with the TRC and the other without. If the driver of each vehicle operates the accelerator pedal in a rough manner while driving over a surface with different surface friction characteristics, the drive wheel on the slippery surface could slip as illustrated. As a result, the vehicle could become unstable. However, when the vehicle is equipped with the TRC, the skid control ECU instantly determines the state of the vehicle and operates the brake actuator in order to apply the brakes to the slipping drive wheel. Furthermore, the ECM receives the signals from the skid control ECU and regulates the throttle in order to control the engine output. Thus, the system can constantly maintain a stable vehicle posture.

X106116E04
3.125,3.469 3.385,3.469 3.385,3.469 4.104,3.854 true 3.125,4.948 3.396,4.948 3.396,4.948 4.51,3.896 true 5.271,2.177 5.052,2.177 5.052,2.177 4.813,2.781 true 2.448,3.219 2.24,3.219 2.24,3.219 2.156,2.76 true 1.302,2.729 1.094,2.729 1.094,2.729 1.01,2.271 true 5.771,2.688 5.5,2.688 5.5,2.688 4.979,3.583 true 2.99,3.385 3.188,3.604 0.198,0.219 10 false *1 2.958,4.875 3.167,5.083 0.208,0.208 10 false *2 0.167,0.094 0.438,0.417 0.271,0.323 12 false *a: 5.302,2.104 5.51,2.313 0.208,0.208 10 false *b 1.333,2.656 1.542,2.865 0.208,0.208 10 false *b 2.479,3.156 2.688,3.365 0.208,0.208 10 false *b 5.823,2.615 6.031,2.823 0.208,0.208 10 false *c 3.125,0.604 3.333,0.813 0.208,0.208 10 false *A 4.281,1.094 4.49,1.302 0.208,0.208 10 false *B

Text in Illustration
*A Without TRC *B With TRC
*1

Brake Actuator Assembly

-

Skid Control ECU



*2

ECM

-

Regulating the throttle to control the engine output



*a Driving condition on road with different surface friction characteristics *b Slippery Surface
*c Brake the slipping drive wheel - -



f.

Vehicle Stability Control (VSC)

i.

The following are two examples that can be considered as circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the motive force and the brakes at each wheel when the vehicle is under one of the conditions indicated below.

X106023E01
1.914,2.317 2.165,2.493 0.252,0.175 10 *a 4.522,2.317 4.774,2.493 0.252,0.175 10 *b

Text in Illustration
*a Front Wheel Skid Tendency *b Rear Wheel Skid Tendency


ii.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate and the vehicle's lateral acceleration, which are then calculated by the skid control ECU.


iii.

Whether or not the vehicle is in the state of front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the yaw rate (a target yaw rate that is determined by the vehicle speed and steering angle) that should be rightfully generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the locus of travel. Thus, the skid control ECU determines that there is a large tendency to front wheel skid.

X106024E01
3.68,0.287 3.932,0.463 0.252,0.175 10 *a 4.506,0.772 4.758,0.948 0.252,0.175 10 *b

Text in Illustration
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel (Based on the Target Yaw Rate)


iv.

Whether the vehicle is in the state of the rear wheel skid or not is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle and the slip angular velocity are large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X106025E03
3.865,0.823 4.177,0.458 4.177,0.458 4.375,0.458 true 3.792,0.896 3.563,0.625 3.563,0.625 3.365,0.625 true 4.083,0.594 4.292,0.802 0.208,0.208 10 false *a 3.188,0.542 3.396,0.75 0.208,0.208 10 false *b 4.406,0.385 4.615,0.594 0.208,0.208 10 false *c

Text in Illustration
*a Movement of Vehicle *b Direction of Travel of the Vehicle's Center of Gravity
*c Slip Angle - -


v.

When the skid control ECU determines that the vehicle has a tendency to front wheel skid or rear wheel skid, it decreases the engine output and applies the brake of a front or rear wheel to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the front wheels and rear wheel of the inner circle of the turn in order to help restrain the front wheel skid tendency.

X106026E03
4.375,0.74 4.698,0.427 4.698,0.427 4.896,0.427 true 4.927,0.333 5.135,0.542 0.208,0.208 10 false *a

Text in Illustration (Making a Right Turn)
*a Control Moment - -
V100135

Brake Force - -


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front and rear wheels of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is enhanced.

X106027E01
4.287,0.756 4.613,0.379 4.613,0.379 4.807,0.379 false 4.847,0.312 5.052,0.517 0.205,0.205 10 *a

Text in Illustration (Making a Right Turn)
*a Control Moment - -
V100135

Brake Force - -



g.

Engine Output Control during TRC or VSC Operation

i.

During the TRC or VSC operation, the skid control ECU outputs the engine output control signal to the ECM. Upon receiving this signal, the ECM inhibits the engine output.

X106028E05
0.104,7.469 5.531,7.854 5.427,0.385 10 false *: The wheel cylinder that activates varies depending on the condition of the vehicle 0.677,5.792 1.552,6.896 0.875,1.104 10 false Brake Wheel Cylinder Fluid Pressure* 0.635,4.292 1.656,4.708 1.021,0.417 10 false Engine Torque 5.698,6.729 6.073,7.021 0.375,0.292 10 false Time 5.698,5.156 6.073,5.448 0.375,0.292 10 false Time 5.698,3.583 6.073,3.875 0.375,0.292 10 false Time 2.25,1.927 2.521,2.219 0.271,0.292 10 false (A) 4.625,0.396 6.802,0.688 2.177,0.292 10 false (A): Start of engine output control 4.625,0.76 6.802,1.052 2.177,0.292 10 false (B): Start of brake control 4.625,1.125 6.802,1.417 2.177,0.292 10 false (C): Brake control completed 4.625,1.469 7.052,1.76 2.427,0.292 10 false (D): Engine output control completed 2.542,1.927 2.813,2.219 0.271,0.292 10 false (B) 4.573,1.906 4.844,2.198 0.271,0.292 10 false (C) 4.875,1.906 5.146,2.198 0.271,0.292 10 false (D) 0.438,2.781 1.656,3.198 1.219,0.417 10 false Vehicle Condition 0.271,1.438 1.969,2.094 1.698,0.656 10 false Level of Strong Front Wheel Skid or Rear Wheel Skid



h.

Hill-start Assist Control

i.

When the vehicle starts off on a steep or slippery hill, it may start to descend backward while the driver switches from the brake pedal to the accelerator pedal, thus making it difficult for the vehicle to start off. To prevent this from occurring, the Hill-start Assist Control temporarily (approximately 2 seconds at the maximum) applies the brakes to the 4 wheels in order to prevent the vehicle from descending backward.


ii.

Without the hill-start assist control, the driver must quickly and precisely switch from the brake pedal to the accelerator pedal. With the hill-start assist control, however, the driver may start off easily and operate the pedal in a relaxed manner, because the hill-start assist control prevents the vehicle from descending backward.

X112168C02
0.521,0.24 3.531,2.271 3.01,2.031 3.635,0.24 6.646,2.271 3.01,2.031 0.583,0.25 0.896,0.406 0.313,0.156 10 false *a 3.698,0.281 4.01,0.438 0.313,0.156 10 false *b 2.021,1.917 2.333,2.073 0.313,0.156 10 false *c
*a Models with Hill-start Assist Control *b Models without Hill-start Assist Control
*c Prevents vehicle from descending backward by controlling brakes. - -



iii.

Hill-start Assist Control Activation Conditions

·

The skid control ECU judges if the vehicle is on an uphill incline based on signals from the deceleration sensor, and activates Hill-start Assist Control when the vehicle is started with all of the following conditions met.


Control Activation Conditions

*1: Models with automatic transaxle

*2: Models with manual transaxle

·

The shift lever is in any position other than P or N (Forward climbing and backward climbing).*1

·

The shift lever is in a position other than R when starting off forward on an upward incline or in R when starting off backward on an upward incline.*2

·

The vehicle is at a standstill.

·

The accelerator pedal is not depressed.

·

The parking brake is released.




iv.

Hill-start Assist Control Cancelation Conditions

·

If any of the following conditions is met, Hill-start Assist Control operation is canceled.


Control Cancelation Conditions

*1: Models with automatic transaxle

*2: Models with manual transaxle

·

The shift lever is moved to P or N.*1

·

The shift lever is shifted to R when starting off forward on an upward incline or from R when starting off backward on an upward incline.*2

·

The accelerator pedal is depressed.

·

The parking brake is operated.

·

Approximately 2 seconds elapse since the operation started.





i.

Outline of Brake Control (Pre-crash Safety System Operating)*

i.

If the pre-crash safety city sensor determines that the possibility of a collision is high, the sensor sends the pre-crash brake assist request signal to the skid control ECU. Upon receiving the signal, the skid control ECU switches the brake assist to standby mode. When the driver depresses the brake pedal, the skid control ECU operates the brake assist based on the master cylinder pressure sensor.


ii.

If the pre-crash safety city sensor determines a collision is unavoidable, the sensor sends the pre-crash brake request signal to the skid control ECU. The skid control ECU then activates the brake actuator as a pre-crash brake control and decelerates the vehicle. Thus, the system helps to lessen impact in collision.

*: Models with Toyota Safety Sense

X124768C01
2.042,0.938 2.25,0.333 2.25,0.333 2.417,0.333 true 2.49,0.229 2.802,0.385 0.313,0.156 10 false *1 0.417,0.781 0.583,0.948 0.167,0.167 10 false *a 0.417,2.729 0.729,2.885 0.313,0.156 10 false *b 0.417,4.542 0.729,4.698 0.313,0.156 10 false *c 0.177,0.135 0.344,0.302 0.167,0.167 10 false *A
*A Brake Operation - -
*1 Pre-crash Safety City Sensor - -
*a Brake Assist Standby Mode *b Brake Assist Operation
*c Brake Operation - -




j.

Emergency Brake Signal

i.

The emergency brake signal automatically flashes the hazard warning lights in the case of emergency braking in order to reduce the risk of being rear ended by a following vehicle.


ii.

The skid control ECU detects the vehicle condition and braking operation using the speed sensors and stop light switch assembly.


iii.

If emergency braking is detected based on these various signals, the skid control ECU sends a signal to the combination meter assembly to flash the hazard warning lights.




FUNCTION


a.

VSC OFF Switch

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on the dirt road, the engine output control is stopped to maintain drive torque.


ii.

The VSC OFF switch can select the 3 modes (Normal Mode, TRC-OFF Mode, VSC-OFF Mode). When the VSC OFF switch is pressed briefly, TRC-OFF Mode is entered and the TRC function will be disabled. When the VSC OFF switch is pressed and held for 3 seconds or more, VSC-OFF Mode is entered and the TRC and VSC functions will be disabled.


iii.

After the power source is turned off in the TRC-OFF Mode or VSC-OFF Mode, turning the power source on again selects the Normal Mode. The system also enters Normal Mode automatically when the vehicle speed increases.

X106029E11
3.167,0.771 4.625,1.052 1.458,0.281 10 false Normal Mode 2.104,2.063 3.563,2.344 1.458,0.281 10 false VSC-OFF Mode 0.604,2.958 5.323,3.24 4.719,0.281 10 false : VSC OFF Switch Operation (Briefly press) 0.604,3.323 5.323,3.604 4.719,0.281 10 false : VSC OFF Switch Operation (Press and hold for 3 seconds or more) 4.073,2.052 5.531,2.333 1.458,0.281 10 false TRC-OFF Mode


iv.

The operations of the brake control functions in each mode are as follows:

Item Brake Control Function TRC OFF Indicator Light VSC OFF Indicator Light
TRC VSC
Normal Mode ○ ○ Light Off Light Off
TRC-OFF Mode - ○ Light On Light Off
VSC-OFF Mode - -* Light On Light On

○: Controllable

-: Not Controllable


HINT:

*: The control is effected during braking or while the yaw rate is large.





CONSTRUCTION


a.

Brake Actuator Assembly

i.

The brake actuator assembly consists of the actuator portion and skid control ECU.


ii.

The actuator portion regulates the hydraulic brake pressure to each wheel cylinder.

X106031E04
2.833,0.677 2.615,0.5 2.615,0.5 2.469,0.5 true 2.667,0.948 2.448,0.76 2.448,0.76 2.292,0.76 true 3.094,0.698 2.813,0.24 2.813,0.24 2.656,0.24 true 3.625,0.865 3.896,0.542 3.896,0.542 4.042,0.542 true 4.406,1.208 4.688,0.885 4.688,0.885 4.833,0.885 true 2.375,1.323 2.094,1.646 2.094,1.646 1.948,1.646 false 3.198,1.542 2.719,2.583 2.719,2.583 2.573,2.583 true 3.365,0.76 3.635,0.344 3.635,0.344 3.781,0.344 true 4.875,0.823 5.125,1 0.25,0.177 10 false *1 4.083,0.479 4.333,0.656 0.25,0.177 10 false *f 3.813,0.26 4.063,0.438 0.25,0.177 10 false *e 2.49,0.167 2.74,0.344 0.25,0.177 10 false *d 2.323,0.417 2.573,0.594 0.25,0.177 10 false *c 2.115,0.677 2.365,0.854 0.25,0.177 10 false *b 1.781,1.552 2.031,1.729 0.25,0.177 10 false *a 2.385,2.5 2.635,2.677 0.25,0.177 10 false *a

Text in Illustration
*1 Skid Control ECU - -
*a From Master Cylinder *b Actuator Portion
*c To Front Wheel Cylinder RH *d To Rear Wheel Cylinder LH
*e To Rear Wheel Cylinder RH *f To Front Wheel Cylinder LH


iii.

The brake actuator assembly is constructed with the following hydraulic circuit:

X106033E06
2.01,3.677 1.729,3.521 true 2.01,3.677 2.281,3.51 true 5.177,3.677 4.896,3.521 true 5.177,3.677 5.448,3.51 true 2.01,5.698 1.729,5.271 true 2.01,5.688 2.281,5.25 true 5.177,5.708 4.896,5.281 true 5.177,5.719 5.448,5.281 true 3.583,3.271 3.208,2.75 true 3.583,3.271 3.979,2.75 true 3.594,6.104 3.292,5.896 true 3.594,6.104 3.875,5.896 true 1.073,1.865 0.594,1.865 true 6.094,1.896 6.615,1.896 true 1.531,0.302 1.76,0.51 0.229,0.208 10 false *a 5.479,0.313 5.708,0.521 0.229,0.208 10 false *a 3.51,0.729 3.74,0.938 0.229,0.208 10 false *1 3.51,3.333 3.74,3.542 0.229,0.208 10 false *5 1.938,3.708 2.135,3.875 0.198,0.167 10 false *4 5.115,3.74 5.313,3.906 0.198,0.167 10 false *4 1.938,5.74 2.135,5.906 0.198,0.167 10 false *6 5.115,5.75 5.313,5.917 0.198,0.167 10 false *6 3.51,6.167 3.74,6.375 0.229,0.208 10 false *7 2.74,7.354 2.969,7.563 0.229,0.208 10 false *9 1.125,7.344 1.354,7.552 0.229,0.208 10 false *8 5.875,7.354 6.156,7.563 0.281,0.208 10 false *11 4.26,7.354 4.573,7.563 0.313,0.208 10 false *10 5.375,1.083 5.604,1.292 0.229,0.208 10 false *2 6.667,1.833 6.896,2.042 0.229,0.208 10 false *3 0.385,1.802 0.615,2.01 0.229,0.208 10 false *3

Text in Illustration
*1 Brake Actuator Assembly *2 Master Cylinder Pressure Sensor
*3 Master Cylinder Cut Solenoid Valve *4 Pressure Holding Solenoid Valve
*5 Pump *6 Pressure Reduction Solenoid Valve
*7 Reservoir *8 Front Wheel Cylinder LH
*9 Rear Wheel Cylinder RH *10 Rear Wheel Cylinder LH
*11 Front Wheel Cylinder RH - -
*a From Master Cylinder - -



b.

Speed Sensor

i.

An active type speed sensor is used. This sensor contains a Hall IC.


ii.

The sensor rotor, which consists of N and S poles that are arranged in a circle, is integrated with the hub bearing inner race.


iii.

An active type speed sensor uses a Hall IC to detect magnetic field changes caused when the sensor rotor rotates, and the sensor outputs the detected information to the skid control ECU as digital pulses.


iv.

To detect the vehicle speed, the frequency of the output pulses is used. Because the active type sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.

X106034E06
5.688,3.198 5.25,3.198 true 4.354,6.927 4.844,6.583 4.844,6.583 4.979,6.583 true 1.615,5.594 3.198,6.073 1.583,0.479 10 false Vehicle Speed 1.573,6.76 3.156,7.24 1.583,0.479 10 false Sensor Output 3.521,7.271 5.104,7.75 1.583,0.479 10 false Time 1.604,4.417 3.844,4.896 2.24,0.479 10 false N and S Poles Arrangement 5.021,6.5 6.604,6.979 1.583,0.479 10 false Digital Pulses 5.75,3.104 7.073,3.583 1.323,0.479 10 false SPEED SENSOR 4,1.344 4.521,1.531 0.521,0.188 10 false Hall IC 2.021,2.094 2.979,2.573 0.958,0.479 10 false Sensor Rotor



c.

Yaw Rate and Deceleration Sensor

i.

The yaw rate and deceleration sensor is built into the airbag sensor assembly.


ii.

The yaw rate sensor detects acceleration in the horizontal forward-backward and left-right directions using the signals from 2 acceleration sensors, and transmits signals to the skid control ECU.

X106035E04
1.167,1.802 0.729,2.25 0.729,2.25 0.531,2.25 true 0.344,2.167 0.552,2.375 0.208,0.208 10 false *1

Text in Illustration
*1

Airbag Sensor Assembly

-

Yaw Rate and Deceleration Sensor



- -
V100135

Front - -

NOTICE:

After replacing the airbag sensor assembly, or the skid control ECU, initialization of the yaw rate and deceleration sensor is required. For the actual procedure, refer to the Repair Manual.




d.

Steering Angle Sensor

i.

The steering angle sensor detects the steering direction and angle, and sends this signal to the skid control ECU.


ii.

The steering angle sensor contains two sets of magnetic resistance elements that detect the rotational movement of a magnet that is built into the detection gear. Thus, the sensor detects the changes that occur in the magnetic resistance elements along with the rotational movement of the detection gear, in order to detect the rotational movement of the steering wheel.

X106036E04
3.25,1.875 2.938,2.333 2.938,2.333 2.708,2.333 true 3.677,1.813 4.25,2.229 true 3.865,1.74 4.25,2.229 4.25,2.229 4.479,2.229 true 2.521,2.24 2.75,2.479 0.229,0.24 10 false *1 4.521,2.135 4.75,2.375 0.229,0.24 10 false *2

Text in Illustration
*1 Steering Angle Sensor *2 Detection Gear

NOTICE:

Do not remove the steering angle sensor from the spiral cable. If there is a malfunction in the steering angle sensor, replace the spiral cable with steering angle sensor.





OPERATION


a.

ABS with EBD

i.

Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.

Not Activated Normal Braking
Activated Increase Mode
Hydraulic Circuit
X132649E02
0.979,0.917 1.156,0.917 1.156,0.917 1.708,1.396 true 0.958,2.167 1.167,2.167 1.167,2.167 1.708,2.854 true 0.542,0.823 0.979,1.135 0.438,0.313 10 false Port A 0.521,2.073 0.958,2.375 0.438,0.302 10 false Port B 1.26,3.99 2.438,4.563 1.177,0.573 10 false To Wheel Cylinder

Pressure Holding Valve (Port A) OFF (Open)
Pressure Reduction Valve (Port B) OFF (Closed)
Brake Wheel Cylinder Pressure Increased

Not Activated -
Activated Holding Mode
Hydraulic Circuit
X132650

Pressure Holding Valve (Port A) ON (Closed)
Pressure Reduction Valve (Port B) OFF (Closed)
Brake Wheel Cylinder Pressure Held

Not Activated -
Activated Reduction Mode
Hydraulic Circuit
X132651E01
0.177,2.458 0.979,3.458 0.802,1 10 false To Reservoir and Pump 1.083,3.927 2.542,4.448 1.458,0.521 10 false From Wheel Cylinder

Pressure Holding Valve (Port A) ON (Closed)
Pressure Reduction Valve (Port B) ON (Open)
Brake Wheel Cylinder Pressure Reduced



b.

Brake Assist

i.

In the event of emergency braking, the skid control ECU detects the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a greater fluid pressure than the master cylinder.

X136275E01
0.167,0.552 3.375,0.75 3.208,0.198 10 false Front Speed Sensor RH 0.167,0.99 3.375,1.188 3.208,0.198 10 false Front Speed Sensor LH 0.167,1.438 2.448,1.802 2.281,0.365 10 false Rear Speed Sensor RH (Skid Control Sensor Wire RH) 0.167,2.229 2.427,2.615 2.26,0.385 10 false Rear Speed Sensor LH (Skid Control Sensor Wire LH) 0.167,3.021 3.375,3.219 3.208,0.198 10 false Stop Light Switch Assembly 0.667,5.417 3.875,5.615 3.208,0.198 10 false : CAN Communication Line 4.271,4.729 6.177,5.01 1.906,0.281 10 false ABS Warning Light 4.052,4.333 5.958,4.615 1.906,0.281 10 false Combination Meter Assembly 2.958,0.156 4.865,0.438 1.906,0.281 10 false Brake Actuator Assembly 3.177,0.542 5.083,0.823 1.906,0.281 10 false Skid Control ECU 3.344,1.552 5.25,1.833 1.906,0.281 10 false Solenoid Relay 3.354,2.25 5.26,2.531 1.906,0.281 10 false Motor Relay 3.354,2.719 4.26,3.135 0.906,0.417 10 false Motor Failsafe Relay 5.188,0.542 6.427,0.948 1.24,0.406 10 false Master Cylinder Cut Solenoid Valves (2) 5.188,1.396 6.427,1.802 1.24,0.406 10 false Solenoid Valves (8) 5.177,2.26 6.417,2.667 1.24,0.406 10 false Pump Motor 5.188,3.104 6.76,3.469 1.573,0.365 10 false Master Cylinder Pressure Sensor

X106060E09
2.406,3.281 2.729,2.604 2.729,2.604 2.594,2.604 true 2.396,4.615 2.042,5.854 2.042,5.854 1.906,5.854 true 3.906,5.906 3.604,6.25 3.604,6.25 3.354,5.917 true 4.771,4.604 5.135,5.844 5.135,5.844 5.271,5.844 true 4.063,2.958 3.594,3.333 3.594,3.333 3.115,2.938 true 4.75,3.26 4.438,2.583 4.438,2.583 4.573,2.583 true 0.667,1.927 0.813,1.927 0.813,1.927 1.333,2.125 true 0.677,3.542 0.823,3.542 0.823,3.542 1.583,3.24 true 0.688,4.865 0.833,4.865 0.833,4.865 1.594,4.542 true 6.49,1.927 6.333,1.927 6.333,1.927 5.823,2.125 true 6.479,3.531 6.344,3.531 6.344,3.531 5.573,3.229 true 6.469,4.896 6.323,4.896 6.323,4.896 5.563,4.573 true 3.26,6.281 3.917,6.5 0.656,0.219 10 false Reservoir 2.594,0.792 4.198,1.01 1.604,0.219 10 false Brake Actuator Assembly 2.938,1.198 5.771,1.573 2.833,0.375 10 false Master Cylinder Pressure Sensor 3.406,3.354 3.813,3.719 0.406,0.365 10 false Pump 1.531,0.292 3.052,0.698 1.521,0.406 10 false From Master Cylinder 0.073,1.833 0.635,2.135 0.563,0.302 10 false Port (A) 2.01,2.531 2.573,2.813 0.563,0.281 10 false Port (D) 0.854,7.135 1.729,7.802 0.875,0.667 10 false Front Wheel Cylinder LH 2.49,7.146 3.344,7.813 0.854,0.667 10 false Rear Wheel Cylinder RH 4.052,7.135 4.917,7.792 0.865,0.656 10 false Rear Wheel Cylinder LH 5.625,7.135 6.458,7.802 0.833,0.667 10 false Front Wheel Cylinder RH 4.656,2.521 5.25,2.802 0.594,0.281 10 false Port (E) 6.542,1.854 7.104,2.24 0.563,0.385 10 false Port (B) 6.531,3.438 7.094,3.75 0.563,0.313 10 false Port (F) 6.542,4.802 7.094,5.094 0.552,0.292 10 false Port (J) 5.333,5.76 5.844,6.125 0.51,0.365 10 false Port (I) 1.333,5.76 1.885,6.073 0.552,0.313 10 false Port (H) 1.323,2.688 1.542,2.865 0.219,0.177 10 false (1) 1.51,3.802 1.76,4.021 0.25,0.219 10 false (3) 1.51,5.146 1.76,5.354 0.25,0.208 10 false (7) 2.344,3.802 2.594,4.01 0.25,0.208 10 false (4) 5.74,2.698 5.958,2.885 0.219,0.188 10 false (2) 4.688,3.802 4.917,4.01 0.229,0.208 10 false (5) 5.5,3.802 5.729,4 0.229,0.198 10 false (6) 2.333,5.146 2.583,5.365 0.25,0.219 10 false (8) 4.688,5.146 4.917,5.333 0.229,0.188 10 false (9) 5.458,5.156 5.781,5.375 0.323,0.219 10 false (10) 0.104,3.438 0.646,3.771 0.542,0.333 10 false Port (C) 0.073,4.771 0.667,5.094 0.594,0.323 10 false Port (G) 4.313,0.281 5.719,0.656 1.406,0.375 10 false From Master Cylinder

Item Port Not Activated Activated
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON*
(2) (B) OFF (Open) ON*
Pressure Holding Solenoid Valve (3) (C) OFF (Open) ←
(4) (D) OFF (Open) ←
(5) (E) OFF (Open) ←
(6) (F) OFF (Open) ←
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ←
(8) (H) OFF (Close) ←
(9) (I) OFF (Close) ←
(10) (J) OFF (Close) ←
Pump OFF ON

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "close" according to the operating condition by adjusting continually.




c.

TRC

i.

The fluid pressure generated by the pump motor is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding and pressure increase modes to control the slippage of the drive wheels. The diagram below shows the hydraulic circuit in the pressure increase mode when the TRC is activated. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on/off according to the ABS with EBD operation pattern.

X136276E01
0.156,0.552 3.365,0.75 3.208,0.198 10 false Front Speed Sensor RH 0.167,0.99 3.375,1.188 3.208,0.198 10 false Front Speed Sensor LH 0.167,1.438 2.438,1.896 2.271,0.458 10 false Rear Speed Sensor RH (Skid Control Sensor Wire RH) 0.167,2.229 2.438,2.688 2.271,0.458 10 false Rear Speed Sensor LH (Skid Control Sensor Wire LH) 0.156,3.021 2.427,3.479 2.271,0.458 10 false Stop Light Switch Assembly 0.167,3.448 2.438,3.906 2.271,0.458 10 false VSC OFF Switch 0.219,4.333 2.49,4.792 2.271,0.458 10 false Steering Angle Sensor 0.208,4.99 2.479,5.448 2.271,0.458 10 false Airbag Sensor Assembly 0.271,5.385 2.573,5.656 2.302,0.271 10 false Yaw Rate and Deceleration Sensor 0.177,6.448 2.479,6.719 2.302,0.271 10 false Throttle Body with Motor Assembly 0.281,6.833 2.583,7.104 2.302,0.271 10 false Throttle Position Sensor 0.292,7.271 2.594,7.542 2.302,0.271 10 false Throttle Control Motor 0.688,8.458 2.99,8.729 2.302,0.271 10 false : CAN Communication Line 3.188,6.458 3.885,6.698 0.698,0.24 10 false ECM 4.063,4.333 6.583,4.594 2.521,0.26 10 false Combination Meter Assembly 4.281,4.729 6.802,4.99 2.521,0.26 10 false TRC OFF Indicator Light 4.281,5.208 6.802,5.469 2.521,0.26 10 false Slip Indicator Light 2.938,0.146 5.458,0.406 2.521,0.26 10 false Brake Actuator Assembly 3.188,0.552 4.542,0.792 1.354,0.24 10 false Skid Control ECU 3.333,1.552 4.688,1.792 1.354,0.24 10 false Solenoid Relay 3.344,2.24 4.698,2.479 1.354,0.24 10 false Motor Relay 3.344,2.729 4.24,3.167 0.896,0.438 10 false Motor Failsafe Relay 5.177,0.542 6.438,0.958 1.26,0.417 10 false Master Cylinder Cut Solenoid Valves (2) 5.177,1.396 6.438,1.813 1.26,0.417 10 false Solenoid Valves (8) 5.177,2.25 6.438,2.667 1.26,0.417 10 false Pump Motor 5.188,3.104 6.75,3.521 1.563,0.417 10 false Master Cylinder Pressure Sensor


ii.

By way of example, the brake hydraulic circuit under the pressure increase mode of TRC is shown below.

X106065E11
2.406,3.292 2.719,2.604 2.719,2.604 2.583,2.604 true 2.406,4.615 2.052,5.844 2.052,5.844 1.917,5.844 true 3.927,5.885 3.625,6.219 3.625,6.219 3.354,5.906 true 4.771,4.635 5.125,5.875 5.125,5.875 5.26,5.875 true 4.052,2.99 3.542,3.375 3.542,3.375 3.104,3.01 true 4.76,3.229 4.448,2.542 4.448,2.542 4.583,2.542 true 0.677,1.917 0.833,1.917 0.833,1.917 1.354,2.115 true 0.688,3.531 0.823,3.531 0.823,3.531 1.594,3.229 true 0.698,4.875 0.844,4.875 0.844,4.875 1.604,4.552 true 6.49,1.938 6.344,1.938 6.344,1.938 5.823,2.135 true 6.479,3.531 6.333,3.531 6.333,3.531 5.573,3.229 true 6.479,4.896 6.333,4.896 6.333,4.896 5.573,4.573 true 3.354,6.25 4.031,6.552 0.677,0.302 10 false Reservoir 2.583,0.823 4.698,1.146 2.115,0.323 10 false Brake Actuator Assembly 2.969,1.219 5.802,1.594 2.833,0.375 10 false Master Cylinder Pressure Sensor 3.406,3.417 3.802,3.802 0.396,0.385 10 false Pump 1.552,0.292 3.104,0.625 1.552,0.333 10 false From Master Cylinder 0.063,1.833 0.656,2.094 0.594,0.26 10 false Port (A) 1.969,2.51 2.542,2.729 0.573,0.219 10 false Port (D) 0.844,7.135 1.844,7.76 1,0.625 10 false Front Wheel Cylinder LH 2.49,7.115 3.385,7.781 0.896,0.667 10 false Rear Wheel Cylinder RH 4.052,7.125 4.896,7.781 0.844,0.656 10 false Rear Wheel Cylinder LH 5.625,7.146 6.552,7.781 0.927,0.635 10 false Front Wheel Cylinder RH 4.646,2.479 5.198,2.698 0.552,0.219 10 false Port (E) 6.542,1.865 7.115,2.083 0.573,0.219 10 false Port (B) 6.552,3.438 7.083,3.708 0.531,0.271 10 false Port (F) 6.552,4.802 7.063,5.115 0.51,0.313 10 false Port (J) 5.302,5.792 5.844,6.094 0.542,0.302 10 false Port (I) 1.344,5.729 1.885,6 0.542,0.271 10 false Port (H) 1.281,2.688 1.5,2.865 0.219,0.177 10 false (1) 1.51,3.813 1.76,4.031 0.25,0.219 10 false (3) 1.51,5.146 1.76,5.354 0.25,0.208 10 false (7) 2.344,3.823 2.594,4.031 0.25,0.208 10 false (4) 5.75,2.698 5.969,2.885 0.219,0.188 10 false (2) 4.677,3.813 4.906,4.021 0.229,0.208 10 false (5) 5.5,3.833 5.729,4.031 0.229,0.198 10 false (6) 2.344,5.156 2.594,5.375 0.25,0.219 10 false (8) 4.688,5.167 4.917,5.354 0.229,0.188 10 false (9) 5.448,5.177 5.771,5.396 0.323,0.219 10 false (10) 0.063,3.427 0.646,3.802 0.583,0.375 10 false Port (C) 0.094,4.781 0.688,5.083 0.594,0.302 10 false Port (G) 4.313,0.302 5.76,0.646 1.448,0.344 10 false From Master Cylinder

Item Port Not Activated Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ← ←
(2) (B) OFF (Open) ON* ← ←
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) ← ← ON (Close)
(6) (F) OFF (Open) ← ← ON (Close)
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ← ← ON (Open)
(10) (J) OFF (Close) ← ← ON (Open)
Brake Wheel Cylinder Pressure Right - - Increase Hold Reduce
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) ON (Close) ← ←
(5) (E) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (8) (H) OFF (Close) ← ← ←
(9) (I) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - - - -
Left - - - - -
Pump OFF ON ← ←

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "close" according to the operating condition by adjusting continually.




d.

VSC

i.

The VSC, by way of solenoid valves, controls the fluid pressure that is generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding and pressure increase modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.

X136277E01
0.177,0.552 3.385,0.75 3.208,0.198 10 false Front Speed Sensor RH 0.177,0.99 3.385,1.188 3.208,0.198 10 false Front Speed Sensor LH 0.167,1.427 2.438,1.844 2.271,0.417 10 false Rear Speed Sensor RH (Skid Control Sensor Wire RH) 0.156,2.229 2.417,2.646 2.26,0.417 10 false Rear Speed Sensor LH (Skid Control Sensor Wire LH) 0.156,3.021 2.417,3.438 2.26,0.417 10 false Stop Light Switch Assembly 0.167,3.458 2.427,3.875 2.26,0.417 10 false VSC OFF Switch 2.938,0.146 5.198,0.563 2.26,0.417 10 false Brake Actuator Assembly 3.198,0.542 4.375,0.813 1.177,0.271 10 false Skid Control ECU 3.333,1.542 4.51,1.813 1.177,0.271 10 false Solenoid Relay 3.333,2.25 4.51,2.521 1.177,0.271 10 false Motor Relay 3.344,2.729 4.24,3.156 0.896,0.427 10 false Motor Failsafe Relay 5.188,0.542 6.427,0.99 1.24,0.448 10 false Master Cylinder Cut Solenoid Valves (2) 5.177,1.396 6.417,1.844 1.24,0.448 10 false Solenoid Valves (8) 5.188,2.25 6.427,2.698 1.24,0.448 10 false Pump Motor 5.177,3.104 6.76,3.552 1.583,0.448 10 false Master Cylinder Pressure Sensor 0.208,4.333 2.469,4.75 2.26,0.417 10 false Steering Angle Sensor 0.208,4.99 2.469,5.406 2.26,0.417 10 false Airbag Sensor Assembly 0.26,5.385 2.521,5.802 2.26,0.417 10 false Yaw Rate and Deceleration Sensor 4.052,4.333 6.313,4.75 2.26,0.417 10 false Combination Meter Assembly 4.26,4.729 6.521,5.146 2.26,0.417 10 false TRC OFF Indicator Light 4.271,5.208 6.531,5.625 2.26,0.417 10 false VSC OFF Indicator Light 4.271,5.688 6.531,6.104 2.26,0.417 10 false Slip Indicator Light 0.167,6.438 2.427,6.854 2.26,0.417 10 false Throttle Body with Motor Assembly 0.281,6.823 2.542,7.24 2.26,0.417 10 false Throttle Position Sensor 0.281,7.26 2.542,7.677 2.26,0.417 10 false Throttle Control Motor 3.188,6.458 3.74,6.771 0.552,0.313 10 false ECM 0.677,8.406 3.073,8.677 2.396,0.271 10 false : CAN Communication Line


ii.

In the front wheel skid restraining control, the brakes of the front wheels and rear wheel of the inner circle of the turn is applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle makes a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation pattern.

X106069E09
2.427,3.958 2.74,3.271 2.74,3.271 2.604,3.271 true 2.417,5.271 2.063,6.5 2.063,6.5 1.927,6.5 true 3.313,6.542 3.583,6.865 3.583,6.865 3.896,6.542 true 4.781,5.271 5.135,6.51 5.135,6.51 5.271,6.51 true 4.115,3.656 3.625,4.094 3.625,4.094 3.125,3.698 true 4.781,3.938 4.458,3.25 4.458,3.25 4.594,3.25 true 0.677,2.604 0.833,2.604 0.833,2.604 1.354,2.802 true 0.698,4.219 0.844,4.219 0.844,4.219 1.604,3.917 true 0.688,5.583 0.833,5.583 0.833,5.583 1.604,5.26 true 6.49,2.604 6.333,2.604 6.333,2.604 5.813,2.802 true 6.5,4.219 6.354,4.219 6.354,4.219 5.594,3.917 true 6.5,5.594 6.344,5.594 6.344,5.594 5.583,5.271 true 3.302,6.896 4.031,7.177 0.729,0.281 10 false Reservoir 2.583,1.375 4.719,1.74 2.135,0.365 10 false Brake Actuator Assembly 2.958,1.813 5.74,2.156 2.781,0.344 10 false Master Cylinder Pressure Sensor 3.438,4.146 3.854,4.552 0.417,0.406 10 false Pump 1.594,0.792 3.115,1.115 1.521,0.323 10 false From Master Cylinder 0.083,2.5 0.646,2.781 0.563,0.281 10 false Port (A) 2.01,3.188 2.583,3.406 0.573,0.219 10 false Port (D) 0.865,7.938 1.708,8.75 0.844,0.813 10 false Front Wheel Cylinder RH 2.5,7.948 3.396,8.76 0.896,0.813 10 false Rear Wheel Cylinder LH 4.083,7.938 4.958,8.719 0.875,0.781 10 false Rear Wheel Cylinder RH 5.635,7.938 6.604,8.802 0.969,0.865 10 false Front Wheel Cylinder LH 4.635,3.177 5.188,3.396 0.552,0.219 10 false Port (E) 6.521,2.521 7.094,2.844 0.573,0.323 10 false Port (B) 6.552,4.125 7.073,4.448 0.521,0.323 10 false Port (F) 6.552,5.5 7.104,5.813 0.552,0.313 10 false Port (J) 5.333,6.448 5.885,6.771 0.552,0.323 10 false Port (I) 1.354,6.406 1.896,6.677 0.542,0.271 10 false Port (H) 1.302,3.385 1.521,3.563 0.219,0.177 10 false (1) 1.531,4.49 1.781,4.708 0.25,0.219 10 false (3) 1.531,5.854 1.781,6.063 0.25,0.208 10 false (7) 2.354,4.49 2.604,4.698 0.25,0.208 10 false (4) 5.75,3.385 5.969,3.573 0.219,0.188 10 false (2) 4.708,4.49 4.938,4.698 0.229,0.208 10 false (5) 5.51,4.5 5.74,4.698 0.229,0.198 10 false (6) 2.354,5.865 2.604,6.083 0.25,0.219 10 false (8) 4.708,5.854 4.938,6.042 0.229,0.188 10 false (9) 5.479,5.906 5.802,6.125 0.323,0.219 10 false (10) 0.115,4.104 0.677,4.427 0.563,0.323 10 false Port (C) 0.094,5.49 0.656,5.792 0.563,0.302 10 false Port (G) 4.302,0.802 5.719,1.188 1.417,0.385 10 false From Master Cylinder 0.083,0.115 4.125,0.563 4.042,0.448 12 false Front Wheel Skid Restraining Control:

Front Wheel Skid Restraining Control
Item Port Not Activated Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON (Close)* ← ←
(2) (B) OFF (Open) ON (Close)* ← ←
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) ← ON (Close) ←
(6) (F) OFF (Open) ← ON (Close) ←
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ← ← ON (Open)
(10) (J) OFF (Close) ← ← ON (Open)
Brake Wheel Cylinder Pressure Right - - Increase Hold Reduce
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) ← ON (Close) ←
(5) (E) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (8) (H) OFF (Close) ← ← ON (Open)
(9) (I) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - Increase - -
Left - - - Hold Reduce
Pump OFF ON ← ←

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "closed" according to the operating condition by adjusting continually.



iii.

In the rear wheel skid restraining control, the brakes of the front wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The hydraulic circuit controls the rear wheel skid condition while the vehicle make a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on/off according to the ABS with EBD operation patterns.

Rear Wheel Skid Restraining Control
Item Port Not Activated Activated
Increase Mode Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ← ←
(2) (B) OFF (Open) ON* ← ←
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) ← ON (Close) ←
(6) (F) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (7) (G) OFF (Close) ← ← ON (Open)
(10) (J) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - - - -
Left - - Increase Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) ON (Close) ← ←
(5) (E) OFF (Open) ON (Close) ← ←
Pressure Reduction Solenoid Valve (8) (H) OFF (Close) ← ← ←
(9) (I) OFF (Close) ← ← ←
Brake Wheel Cylinder Pressure Right - - - - -
Left - - - - -
Pump OFF ON ← ←

HINT:

*: The solenoid valve controls the hydraulic pressure between "open" and "closed" according to the operating condition by adjusting continually.




e.

Hill-start Assist Operation

i.

Hill-start Assist Control controls the brakes by maintaining the master cylinder fluid pressure produced by depressing the brake pedal.

X136262E01
0.167,0.677 1.75,0.885 1.583,0.208 10 false Front Speed Sensor RH 0.167,1.115 1.698,1.302 1.531,0.188 10 false Front Speed Sensor LH 0.167,1.552 2.458,1.938 2.292,0.385 10 false Rear Speed Sensor RH (Skid Control Sensor Wire RH) 0.167,2.344 2.427,2.74 2.26,0.396 10 false Rear Speed Sensor LH (Skid Control Sensor Wire LH) 0.167,3.135 1.969,3.354 1.802,0.219 10 false Stop Light Switch Assembly 2.938,0.26 4.583,0.479 1.646,0.219 10 false Brake Actuator Assembly 3.167,0.667 4.385,0.865 1.219,0.198 10 false Skid Control ECU 3.344,1.667 4.344,1.896 1,0.229 10 false Solenoid Relay 3.344,2.354 4.167,2.563 0.823,0.208 10 false Motor Relay 3.344,2.833 4.24,3.208 0.896,0.375 10 false Motor Failsafe Relay 5.177,0.656 6.417,1.042 1.24,0.385 10 false Master Cylinder Cut Solenoid Valves (2) 5.177,1.521 6.438,1.76 1.26,0.24 10 false Solenoid Valves (8) 5.198,2.365 6.031,2.583 0.833,0.219 10 false Pump Motor 5.177,3.219 6.75,3.563 1.573,0.344 10 false Master Cylinder Pressure Sensor 0.177,4.24 2.354,4.635 2.177,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 0.208,5.406 1.823,5.615 1.615,0.208 10 false Airbag Sensor Assembly 0.271,5.802 2.51,6.021 2.24,0.219 10 false Yaw Rate and Deceleration Sensor 4.01,4.229 6.115,4.448 2.104,0.219 10 false Combination Meter Assembly 4.167,4.667 6.271,4.885 2.104,0.219 10 false Slip Indicator Light 0.646,7.458 2.75,7.677 2.104,0.219 10 false : CAN Communication Line 4.042,5.813 4.51,6.021 0.469,0.208 10 false ECM

Example of Hill-start Assist Control when Climbing Uphill with Shift Lever in D (Driver Depresses Accelerator Pedal to Start Off after Hill-start Assist Control Operation)

X113265E01
2.073,0.875 2.344,0.417 2.344,0.417 2.573,0.417 true 2.26,2.156 2.51,1.354 2.51,1.354 2.75,1.354 true 1.052,0.448 1.604,0.635 0.552,0.188 10 false Forward 0.656,0.802 1.625,1.01 0.969,0.208 10 false Vehicle Speed 0.948,1.198 1.667,1.406 0.719,0.208 10 false Backward 2.646,0.354 3.573,0.563 0.927,0.208 10 false Vehicle Stops 5.333,0.958 5.781,1.156 0.448,0.198 10 false Time 5.365,2.688 5.823,2.885 0.458,0.198 10 false Time 2.844,1.281 4.271,1.75 1.427,0.469 10 false Fluid pressure required to stop the vehicle 4.917,1.625 6.406,1.813 1.49,0.188 10 false : Brake Pedal Operation 4.917,1.365 5.938,1.563 1.021,0.198 10 false : Fluid Pressure 2.49,3.333 4.625,3.583 2.135,0.25 10 false Hill-start Assist Control Operation 2.594,2.865 4.625,3.188 2.031,0.323 10 false Accelerator pedal is depressed 0.667,2.24 1.594,2.417 0.927,0.177 10 false Fluid Pressure

Example of Hill-start Assist Control when Climbing Uphill with Shift Lever in D (Driver Takes No Action after Hill-start Assist Control Operation)

X113266E01
2.281,2.156 2.417,1.073 2.417,1.073 2.531,1.073 true 2.073,0.875 2.333,0.51 2.333,0.51 2.625,0.51 true 1.042,0.469 1.594,0.677 0.552,0.208 10 false Forward 1.135,0.813 2.073,1.01 0.938,0.198 10 false Speed 0.938,1.146 1.635,1.344 0.698,0.198 10 false Backward 0.24,2.094 1.729,2.302 1.49,0.208 10 false Brake Fluid Pressure 2.667,0.458 3.885,0.729 1.219,0.271 10 false Vehicle stopped 2.583,0.99 4.385,1.542 1.802,0.552 10 false Required brake fluid pressure to keep the vehicle stationary 4.792,1.354 6.365,1.594 1.573,0.24 10 false : Brake Fluid Pressure 4.792,1.625 6.323,1.823 1.531,0.198 10 false : Brake Pedal Operation 5.375,0.938 5.823,1.146 0.448,0.208 10 false Time 5.427,2.667 5.854,2.865 0.427,0.198 10 false Time 3.708,2.75 4.698,2.979 0.99,0.229 10 false Approx. 2 sec. 2.698,3.344 4.854,3.573 2.156,0.229 10 false Hill-start Assist Control Operating

Hill-start Assist Operation
X136264E01
0.667,1.833 0.833,1.833 0.833,1.833 1.354,2.135 true 0.667,3.583 0.833,3.583 0.833,3.583 1.594,3.229 true 0.656,4.917 0.823,4.917 0.823,4.917 1.583,4.563 true 1.917,5.75 2.083,5.75 2.083,5.75 2.417,4.563 true 1.917,4.083 2.083,4.083 2.083,4.083 2.417,3.25 true 3.073,3 3.583,3.333 3.583,3.333 4.073,3 true 3.333,5.917 3.583,6.167 3.583,6.167 3.833,5.917 true 5.813,2.167 6.333,1.917 6.333,1.917 6.5,1.917 true 5.563,3.198 6.333,3.417 6.333,3.417 6.5,3.417 true 5.563,4.563 6.333,4.833 6.333,4.833 6.5,4.833 true 4.75,3.229 5.083,4.167 5.083,4.167 5.25,4.167 true 4.75,4.563 5.083,5.75 5.083,5.75 5.25,5.75 true 1.5,0.281 2.917,0.479 1.417,0.198 10 false From Master Cylinder 4.333,0.271 5.75,0.469 1.417,0.198 10 false From Master Cylinder 2.823,0.833 4.531,1.063 1.708,0.229 10 false Brake Actuator Assembly 2.917,1.208 5.448,1.438 2.531,0.229 10 false Master Cylinder Pressure Sensor 0.135,1.719 0.719,1.948 0.583,0.229 10 false Port (A) 0.146,3.49 0.729,3.719 0.583,0.229 10 false Port (C) 0.094,4.781 0.677,5.01 0.583,0.229 10 false Port (G) 1.385,5.646 1.969,5.875 0.583,0.229 10 false Port (H) 1.406,4 1.99,4.229 0.583,0.229 10 false Port (D) 1.302,2.677 1.552,2.906 0.25,0.229 10 false (1) 1.51,3.792 1.76,4.021 0.25,0.229 10 false (3) 2.354,3.802 2.604,4.031 0.25,0.229 10 false (4) 1.531,5.156 1.781,5.385 0.25,0.229 10 false (7) 2.333,5.156 2.583,5.365 0.25,0.208 10 false (8) 3.406,3.354 3.906,3.583 0.5,0.229 10 false Pump 3.313,6.188 3.979,6.417 0.667,0.229 10 false Reservoir 6.552,1.833 7.135,2.063 0.583,0.229 10 false Port (B) 6.573,3.333 7.083,3.583 0.51,0.25 10 false Port (F) 6.552,4.74 7.063,5.052 0.51,0.313 10 false Port (J) 5.313,4.083 5.979,4.313 0.667,0.229 10 false Port (E) 5.302,5.656 5.802,5.906 0.5,0.25 10 false Port (I) 5.729,2.677 5.979,2.906 0.25,0.229 10 false (2) 4.688,3.802 4.938,4.031 0.25,0.229 10 false (5) 5.5,3.802 5.75,4.031 0.25,0.229 10 false (6) 4.688,5.146 4.938,5.375 0.25,0.229 10 false (9) 5.479,5.156 5.813,5.406 0.333,0.25 10 false (10) 0.813,7.115 1.594,7.51 0.781,0.396 10 false Front Wheel Cylinder RH 2.469,7.115 3.25,7.51 0.781,0.396 10 false Rear Wheel Cylinder LH 4.021,7.115 4.802,7.51 0.781,0.396 10 false Rear Wheel Cylinder RH 5.625,7.104 6.406,7.5 0.781,0.396 10 false Front Wheel Cylinder LH

Item Port Not Activated Hill-start Assist Control Activated
Holding Mode Reduction Mode
Master Cylinder Cut Solenoid Valve (1) (A) OFF (Open) ON* ON*
(2) (B) OFF (Open) ON* ON*
Front Brake Pressure Holding Solenoid Valve (3) (C) OFF (Open) OFF (Open) OFF (Open)
(6) (F) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (7) (G) OFF (Closed) OFF (Closed) OFF (Closed)
(10) (J) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - Hold Reduce
Left - - Hold Reduce
Rear Brake Pressure Holding Solenoid Valve (4) (D) OFF (Open) OFF (Open) OFF (Open)
(5) (E) OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve (8) (H) OFF (Closed) OFF (Closed) OFF (Closed)
(9) (I) OFF (Closed) OFF (Closed) OFF (Closed)
Brake Wheel Cylinder Pressure Right - - Hold Reduce
Left - - Hold Reduce
Pump OFF ON ON

HINT:

*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.




f.

Brake Control Operation (Pre-crash Safety System Operating)*

i.

If the pre-crash safety city sensor determines that the possibility of a collision is high, the sensor sends the pre-crash brake assist request signal to the skid control ECU. Upon receiving the signal, the skid control ECU switches the brake assist to standby mode. When the driver depresses the brake pedal, the skid control ECU operates the brake assist based on the master cylinder pressure sensor.


ii.

If a collision is unavoidable, the skid control ECU actuates the motor in the brake actuator assembly to apply direct pressure to the wheel cylinders even if the driver does not press the brake pedal. This brake control operates in the same way as the normal brake operation.

*: Models with Toyota Safety Sense

X136278E01
0.167,0.552 2.135,0.75 1.969,0.198 10 false Front Speed Sensor RH 0.156,0.99 2.125,1.188 1.969,0.198 10 false Front Speed Sensor LH 0.167,1.427 2.438,1.792 2.271,0.365 10 false Rear Speed Sensor RH (Skid Control Sensor Wire RH) 0.167,2.229 2.438,2.594 2.271,0.365 10 false Rear Speed Sensor LH (Skid Control Sensor Wire LH) 0.156,3.01 2.125,3.208 1.969,0.198 10 false Stop Light Switch Assembly 0.208,4.323 2.177,4.521 1.969,0.198 10 false Steering Angle Sensor 0.219,4.979 2.188,5.177 1.969,0.198 10 false Airbag Sensor Assembly 0.26,5.385 2.51,5.677 2.25,0.292 10 false Yaw Rate and Deceleration Sensor 4.042,5.396 6.292,5.688 2.25,0.292 10 false Pre-crash Safety City Sensor 2.927,0.146 5.177,0.438 2.25,0.292 10 false Brake Actuator Assembly 3.177,0.552 5.427,0.844 2.25,0.292 10 false Skid Control ECU 3.344,1.542 5.594,1.833 2.25,0.292 10 false Solenoid Relay 3.344,2.24 4.365,2.542 1.021,0.302 10 false Motor Relay 3.344,2.719 4.24,3.177 0.896,0.458 10 false Motor Failsafe Relay 5.188,0.542 6.427,0.948 1.24,0.406 10 false Master Cylinder Cut Solenoid Valves (2) 5.177,1.385 6.417,1.792 1.24,0.406 10 false Solenoid Valves (8) 5.177,2.25 6.417,2.656 1.24,0.406 10 false Pump Motor 5.177,3.104 6.75,3.542 1.573,0.438 10 false Master Cylinder Pressure Sensor 0.656,6.479 3.26,6.688 2.604,0.208 10 false : CAN Communication Line




FAIL-SAFE


a.

In the event of a malfunction in the ABS, skid control ECU prohibits the brake control system.


b.

In the event of a malfunction in the EBD, the brake system is operated as long as possible even if the ABS is prohibited. If the EBD control becomes impossible, the brake warning light illuminates to inform the driver of that. In this case, the brake system is operated in the same condition as the brake system without the brake control system.


c.

In the event of a malfunction in the TRC and/or VSC, skid control ECU prohibits the TRC and VSC operation.


d.

If a communication malfunction occurs between the skid control ECU and the steering angle sensor, yaw rate and deceleration sensor, or ECM, the skid control ECU stops the TRC and VSC.


e.

When the ECM detects the Diagnostic Trouble Code (DTC), it will disable the TRC and VSC.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, then the ABS warning light, brake warning light, or slip indicator light illuminate either individually or as a group according to the function in which the malfunction has been detected, to alert the driver of the malfunction.


b.

At the same time, the DTCs are stored in memory.


c.

This system has a sensor signal check (test mode) function.


d.

For details of the DTCs that are stored in skid control ECU memory and the DTCs that are output through the sensor signal check functions, see the Repair Manual.