FUNCTION OF MAIN COMPONENTS
Automatic Light Control System
| Component | Function | |
|---|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and illuminates the headlights, taillights, clearance lights and license plate lights. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Transmits an AUTO position signal to the main body ECU (multiplex network body ECU). |
| Automatic Light Control Sensor | Detects the ambient light level. | |
Light Automatic Turn-off System
| Component | Function | |
|---|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals, and turns off the exterior lights. | |
| Front Door Courtesy Light Switch Assembly RH | Detects whether driver's door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Transmits a light control position signal to the main body ECU (multiplex network body ECU). |
LED Headlight System
| Component | Function | |
|---|---|---|
| Main Body ECU (Multiplex Network Body ECU) | The main body ECU (multiplex network body ECU) receives the HEAD position signal from the light control switch and transmits a signal to the headlight relay. | |
| Headlight Relay | The headlight relay supplies power to the LED driver modules (Light Control ECU). | |
| Headlight Assembly | Light Emitting Diode (LED) | The Light Emitting Diode (LED) light shines ahead over a broader area and further forward, increasing the area visible to the driver. |
| LED Driver Module (Light Control ECU) | The LED driver module (Light Control ECU) keeps a constant level of direct current applied to the LED, achieving stable LED illumination. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | The light control switch transmits a HEAD position signal to the main body ECU (multiplex network body ECU). |
Automatic Headlight Beam Level Control System
| Component | Function | |
|---|---|---|
| Headlight Leveling ECU Assembly | ·
The headlight leveling ECU assembly detects changes of vehicle movement based on the rear height control sensor sub-assembly RH and vehicle speed signal. ·
The headlight leveling ECU assembly outputs control signals to the headlight leveling motors based on the detected value. ·
This ECU provides initial set control and a fail-safe function. |
|
| Headlight Assembly | Headlight Leveling Motor | ·
Based on the signals received from headlight leveling ECU assembly, each headlight leveling motor moves the projector unit in the headlight to vary its angle. ·
Each headlight leveling motor uses a stepper motor to precisely regulate the angle of the projector unit. |
| Main Body ECU (Multiplex Network Body ECU) | The main body ECU (multiplex network body ECU) receives a HEAD position signal from the light control switch and transmits it to the headlight leveling ECU assembly. | |
| Rear Height Control Sensor Sub-assembly RH | The rear height control sensor sub-assembly RH detects vehicle movement and transmits a signal to the headlight leveling ECU assembly. | |
| Combination Meter Assembly | The combination meter assembly transmits a vehicle speed signal to the headlight leveling ECU assembly. | |
Light Reminder System
| Component | Function |
|---|---|
| Main Body ECU (Multiplex Network Body ECU) | Outputs taillight illumination signals and driver's door open signals to the combination meter assembly. |
| Front Door Courtesy Light Switch Assembly RH | Detects whether driver's door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). |
| Combination Meter Assembly | Receives taillight illumination signals and driver's door open signals from the main body ECU (multiplex network body ECU) when the ignition switch is turned off, and sounds the buzzer. |
Automatic High Beam System (Models with Toyota Safety Sense)
| Component | Function | |
|---|---|---|
|
*: Models with Automatic Light Control System |
||
| Pre-crash Safety City Sensor (Monocular Camera Sensor) | The pre-crash safety city sensor determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its monocular camera sensor. Then, the sensor sends high beam request signals to the main body ECU (multiplex network body ECU). | |
| Main Body ECU (Multiplex Network Body ECU) | ·
The main body ECU (multiplex network body ECU) receives the signals from the headlight dimmer switch assembly and the automatic light control sensor and the auto high beam switch. ·
The main body ECU (multiplex network body ECU) operates the high beams based on request signals that are received from the pre-crash safety city sensor. ·
The main body ECU (multiplex network body ECU) transmits the signals to the combination meter assembly. |
|
| Airbag Sensor Assembly | Yaw Rate and Acceleration Sensor | Detects the yaw rate of the vehicle and transmits the signal to the pre-crash safety city sensor. |
| Brake Actuator Assembly | Skid Control ECU | Transmits the speed sensor signal to the pre-crash safety city sensor. |
| ECM | Transmits the shift position signal to the pre-crash safety city sensor. | |
| Combination Meter Assembly | Automatic High Beam Indicator Light | ·
The automatic high beam indicator light illuminates (green) to inform the driver when the Automatic High Beam system is activated. ·
The automatic high beam indicator light illuminates (yellow) to inform the driver when a malfunction is detected in this system. |
| Headlight High Beam Indicator Light | The headlight high beam indicator light illuminates (blue) to inform the driver when the high beam headlights are on. | |
| Automatic Light Control Sensor* | The automatic light control sensor detects the ambient light level and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Auto High Beam Switch | The auto high beam switch outputs the switch on signal to the main body ECU (multiplex network body ECU). | |
| Headlight Dimmer Switch Assembly | The headlight dimmer switch assembly transmits the light control switch and dimmer switch signal to the main body ECU (multiplex network body ECU). | |
SYSTEM CONTROL
LED Headlight System
When the light control switch is turned on, the LED driver module (light control ECU) immediately turn on the LEDs (approximately 0.1 sec). In addition, by regulating the output currents flowing into the LEDs at the specified level, the LED driver module (light control ECU) prevent the glare of light due to voltage variation.
If malfunctions occur in the LED headlight system, an LED driver module (light control ECU) transmits fail signals to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives fail signals, it transmits signals to the combination meter, warning the driver.
Automatic Headlight Beam Level Control System
The rear height control sensor sub-assembly RH detects a change in height of the rear shaft in response to the weight applied to the rear of the vehicle when the vehicle is stopped and sends the change amount signal to the headlight leveling ECU. The headlight leveling ECU calculates the vehicle posture based on the change amount and controls the headlight beam level by operating the headlight leveling motor.
Automatic High Beam System (Models with Toyota Safety Sense)
The automatic high beam system operates as follows:
| Function | Operation Condition |
|---|---|
| Active | When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:
·
The ignition switch is ON. ·
The headlight dimmer switch assembly (light control switch) is in the AUTO position or head position and the low beam headlights are on. ·
The headlight dimmer switch assembly (dimmer switch) is in the high beam position. ·
The auto high beam switch is ON. ·
The shift lever is in any position other than R. |
| High Beams on | When all of the following conditions are met, the automatic high beam system turns on the high beams after a short delay:
·
Vehicle speed is more than approximately 34 km/h (21 mph). ·
The area in front of the vehicle is dark. ·
No oncoming vehicles are present with the headlights on. ·
No preceding vehicles are present with the taillights on. ·
Few streetlights are present along the street ahead. |
| High Beams off | When any of the following conditions is met, the automatic high beam system turns off the high beams after a short delay:
·
Vehicle speed is less than approximately 27 km/h (17 mph). ·
The area in front of the vehicle is not dark. ·
An oncoming vehicle with headlights on is detected. ·
A preceding vehicle with taillights on is detected. ·
Several streetlights are present along the street ahead. |
FUNCTION
Light Automatic Turn-off System
The main body ECU (multiplex network body ECU) receives the light control switch signals, front door courtesy light switch assembly RH on/off signal and ignition switch turned off signal, and turns off the exterior lights.
| Light Control Switch Position | Outline |
|---|---|
| TAIL, HEAD, AUTO | While the lights (headlights, front fog lights and taillights) are turned on, this system automatically turns them off when the ignition switch is turned off and the driver's door is opened. |
After the light automatic turn-off system was activated, when the ignition switch is shifted from ON to off while the light control switch (TAIL or HEAD) is turned on, the battery saving function turns off the headlights and taillights automatically in approximately 20 minutes. In addition, when one of the doors is opened from the closed status or closed from the opened status, the accumulated time is reset and the lights turn off in approximately 20 minutes after the door was opened/closed.
The light automatic turn-off system is controlled by the main body ECU (multiplex network body ECU).
Automatic Headlight Beam Level Control System (Models with LED Headlight System)
The automatic headlight beam level control system mainly consists of the headlight leveling ECU assembly, rear height control sensor sub-assembly RH and 2 headlight leveling motors. The headlight leveling ECU assembly controls the system.
The ECU detects the movement of the suspension from the rear height control sensor sub-assembly RH and the vehicle speed from the combination meter sub-assembly.
The ECU then controls the headlight leveling motor based on this information, in order to change the headlight reflector angle.
When the headlight leveling ECU assembly detects that the vehicle is stopped and the ignition switch is ON, the ECU executes the initial setting of the stepper motors.
Light Reminder System
The light reminder system warns the driver using a buzzer when the meter ECU inside the combination meter assembly receives the driver's door courtesy light switch signal via the main body ECU (multiplex network body ECU) and the ignition switch is turned off and the door is opened with the taillights kept on. The buzzer is located inside the combination meter assembly.
| Light Control Switch Position | Ignition Switch | Door | Buzzer |
|---|---|---|---|
| TAIL, HEAD | Switch off | Open | Sounds |
| Closed | - |
Automatic High Beam System (Models with Toyota Safety Sense)
When passing an oncoming vehicle:
The automatic high beam system turns off the high beams before an oncoming vehicle comes within approximately 800 m (2625 ft.).
When an oncoming vehicle passes out of pre-crash safety city sensor (monocular camera sensor) range, the automatic high beam system turns the high beams on after a short delay.
| *a | Approx. 800 m (2625 ft.) | *b | Delay |
| *c | Monocular Camera Sensor Angle | - | - |
The detection distance varies depending on detected objects.
The timing of turning on and off the high beams varies depending on the intensity of oncoming (and preceding) vehicle lights.
When passing a preceding vehicle:
When approaching a preceding vehicle, the automatic high beam system turns off the high beams approximately 600 m (1968 ft.) before reaching it.
When a preceding vehicle passes out of pre-crash safety city sensor (monocular camera sensor) range, the automatic high beam system turns the high beams on after a short delay.
| *a | Approx. 600 m (1968 ft.) | *b | Delay |
| *c | Monocular Camera Sensor Angle | - | - |
The timing of turning on and off the high beams varies depending on the intensity of the preceding vehicle lights.
CONSTRUCTION
LED Driver Module
The LED driver modules are placed beneath the headlights and this supplies a constant voltage to the low beams and reduces the changes in the energization current.
Automatic High Beam System (Models with Toyota Safety Sense)
Pre-crash Safety City Sensor (Monocular Camera Sensor)
The pre-crash safety city sensor (monocular camera sensor) consists of a Complementary Metal Oxide Semiconductor (CMOS) camera that receives images and the mirror portion that identifies light sources and judges whether to use high beams or low beams.
| *1 | Pre-crash Safety City Sensor | - | - |
| *a | Monocular Camera Sensor | - | - |
FAIL-SAFE
LED Headlight System
The LED driver module (light control ECU) executes the fail-safe actions listed below in accordance with the problem that has been detected.
| Problem | Outline |
|---|---|
| Abnormal Output (Open Circuit or Short Circuit) | If an abnormal condition (open or short) occurs in the voltage that is output by the LED driver module (light control ECU), the LED driver module (light control ECU) stops illuminating the headlights and will maintain this state until the power is reinstated. Power is reinstated by turning the headlight dimmer switch assembly (light control switch) from off to on. |
| Abnormal input voltage (High input voltage) | When the headlights are on, if the LED driver module (light control ECU) receives a voltage of more than 17 V, it will turn the headlights off. When the input voltage resumes to the normal operating voltage range, the LED driver module will turn the headlights on. |
| Abnormal input voltage (Low input voltage) | When the headlights are on, if the LED driver module (light control ECU) detects that the input voltage has decreased to 6 to 10V, it will dim the headlights. When the input voltage resumes to a normal operating voltage range, the LED driver module will return the headlight brightness to the normal brightness. |
| If the LED driver module receives a voltage of less than 6 V, it will turn the headlights off. When the power voltage resumes to more than 8.5 V, the LED driver module will turn the headlights on. |
Automatic Headlight Beam Level Control System
If an abnormal condition such as those listed below has been detected, the headlight leveling ECU operates in the fail-safe mode.
| Problem | Outline |
|---|---|
| Power Supply Voltage Malfunction | Holds the beam at the position of the headlight leveling motor when the abnormality has been detected. |
| Rear Height Control Sensor Sub-assembly Data Error During Initialization | |
| Vehicle Model Code Inconsistent | |
| Rear Height Control Sensor Sub-assembly Power Supply Malfunction | |
| Rear Height Control Sensor Sub-assembly Signal Malfunction |
DIAGNOSIS
LED Headlight System
If the main body ECU (multiplex network body ECU) detects a malfunction in the LED headlight system, the combination meter assembly flashes the master warning light and indicates the warning message on the multi-information display. At the same time, the Diagnostic Trouble Code (DTC) is stored in memory. The DTC can be read using the intelligent tester. For details, refer to the Repair Manual.
Automatic Headlight Beam Level Control System
When the headlight leveling ECU assembly detects malfunctions in the automatic headlight beam level control system, DTCs are stored in memory.
The DTCs can be read using the intelligent tester. For details, refer to the Repair Manual.