FUNCTION
Impact Absorbing Structure for Frontal Collision
A structure that ensures collision energy absorption efficiency, dissipates impact, and reduces cabin deformation during a frontal collision has been achieved.
Impact energy during a frontal collision will first be dispersed into the left and right front side members by the front bumper reinforcement. Then, it will be dispersed again into the rocker panel and front under floor.
Impact energy received by the upper member will be dispersed into the front door beltline reinforcements and front body pillar reinforcements.
| *1 | Front Bumper Reinforcement | *2 | Front Side Member |
| *3 | Upper Member | *4 | Front Door Beltline Reinforcement |
| *5 | Front Body Pillar Reinforcement | - | - |
|
Path of Collision Energy |
|
Frontal Collision |
Impact Absorbing Structure for Side Collision
A structure that ensures collision energy absorption efficiency, dissipates impact, and reduces cabin deformation during a side collision has been achieved.
Ultra high strength steel sheet is used for the rocker outer reinforcement and center body pillar upper hinge reinforcement, and high strength steel sheet is used for the center body pillar outer reinforcement and rail outer reinforcement, to ensure high strength.
By providing bulkheads inside the rockers and thus controlling rocker bending, cabin deformation suppression has been aimed for.
Optimal placement of the door side impact protection beams enables a construction that efficiently transmits load.
| *1 | Rocker Outer Reinforcement | *2 | Center Body Pillar Upper Hinge Reinforcement |
| *3 | Center Body Pillar Outer Reinforcement | *4 | Bulkhead |
| *5 | Front Door Side Impact Protection Beam | *6 | Rear Door Side Impact Protection Beam |
| *a | A-A Cross Section | *b | B-B Cross Section |
|
Path of Collision Energy |
|
Side Collision |
Lessening Pedestrian Injury
A front bumper energy absorber and a front bumper energy absorber sub-assembly are provided in front of the front bumper reinforcement and below the lower radiator support. This structure helps lessen the impact applied to the legs of the pedestrians.
| *1 | Front Bumper Energy Absorber | *2 | Front Bumper Energy Absorber Sub-assembly |
| *3 | Front Bumper Reinforcement | *4 | Front Bumper Cover |
| *5 | Lower Radiator Support | - | - |
| *a | A-A Cross Section | - | - |
A pantograph construction, which absorbs the impact it receives while collapsing, is used in the hood reinforcement. During a collision with a pedestrian, a deformable space for the pedestrian's head to strike is provided, which helps to reduce the predicted impact to the pedestrian's head.
| *1 | Hood Reinforcement | *2 | Hood Inner Panel |
| *3 | Hood Sub-assembly | *4 | Hood Striker |
| *5 | Engine | - | - |
| *a | A-A Cross Section | *b | Before Collision |
| *c | Space | - | - |
|
Impact | - | - |
An impact absorbing bracket (front apron to cowl side member plate) is used for the mounting portion of the front fender panel to absorb impact energy to the head of the pedestrian in a collision, thus helps dampening the impact to the head.
| *1 | Front Fender Panel (Front Fender Sub-assembly) | *2 | Impact Absorbing Bracket (Front Apron to Cowl Side Member Plate) |
The cowl uses an open section structure that collapses easily in an impact from the top, thus helps reducing the impact to and head injuries sustained by a pedestrian in an accident.
A certain amount of depth has been provided internally under the location where the windshield wiper is mounted to allow the windshield wiper to be pushed downward if a pedestrian's head collides with the area, thus helps reducing the impact to their head during a collision.
| *1 | Windshield | *2 | Hood Sub-assembly |
| *3 | Windshield Wiper | - | - |
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | Before Collision | *d | Space |
|
Impact | - | - |
In order to help reduce collision impact for pedestrians, a space has been provided under the left and right hood hinge arms so that they can move if a pedestrian's head collides with the hood.
| *1 | Hood Sub-assembly | *2 | Hood Hinge Assembly |
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | Before Collision | *d | Space |
|
Impact | - | - |
Aerodynamics
Spats are fitted at the front of the rear tires to direct the airflow, and this reduces air turbulence into the wheel house, ensuring straight driving stability at high speeds.
The outer rear view mirror shape has been optimized to increase the aerodynamics.
A rear spoiler sub-assembly is provided, giving a rectifying effect and allowing superior aerodynamic performance.
| *A | for Sport Package Models | - | - |
| *1 | Outer Rear View Mirror Assembly | *2 | Rear Spoiler Sub-assembly |
| *3 | Rear Spat (Rear Wheel Opening Extension Pad) | *4 | Center Spat (Rocker Panel Moulding Protector) |
| *5 | Front Spat (Front Wheel Opening Extension Pad) | *6 | Fin |
| *7 | Front Floor Brace Center | - | - |
A grooved structure has been adopted for the front fender liner. This guides airflow inside the wheel housing along the tire, thus smoothing the airflow inside the wheel housing and further enhancing maneuvering stability.
| *1 | Front Fender Liner | *2 | Tire |
| *a | A Site | *b | Fin |
| *c | B - B Cross Section | - | - |
|
Airflow | - | - |
The front fender liner and bracket ensure a space before the vehicle body, which provides efficient ventilation of the air inside the engine compartment.
| *1 | Front Fender Liner | *2 | Front Fender Liner Bracket |
| *3 | Body | - | - |
| *a | A - A Cross Section | - | - |
|
Airflow | - | - |
CONSTRUCTION
Lightweight and Highly Rigid Body
High strength steel sheet and ultra high strength steel sheet are used in order to achieve excellent body rigidity and a lightweight body.
|
High Strength Steel Sheet |
|
Ultra High Strength Steel Sheet |
Body Shell Construction
Sufficient rigidity has been ensured by using the outer cowl top panel as a framework cross member to smoothly connect the left and right front suspension towers. In this way, good driving stability has been achieved.
| *1 | Outer Cowl Top Panel | - | - |
|
Front | - | - |
Spot welds have been added around the front body pillar and rear inner roof side to improve body rigidity.
| *a | Front Body Pillar | *b | Rear Inner Roof Side |
| *c | Spot welds | - | - |
The thicknesses of the front body pillar lower gusset on the left and right sides of the instrument panel reinforcement, and of the front body pillar lower brace on the left and right sides of the dash panel have been optimized.
| *1 | Front Body Pillar Lower Brace | *2 | Front Body Pillar Lower Gusset LH |
| *3 | Front Body Pillar Lower Gusset RH | - | - |
Anti-corrosion Sheet Steel
Anti-corrosion sheet steel is used as in the following illustration:
|
Anti-corrosion Sheet Steel | - | - |
Wax and Anti-chipping Application
Wax is applied to front end of hood sub-assembly, edge of the door lower portion and fuel filler lid hinge to improve rust-resistant performance.
To protect the paint from chipping, anti-chipping paint is applied to the rockers and the front end of the hood sub-assembly.
| *1 | Fuel Filler Lid Hinge | *2 | Door Hinge |
| *a | The illustrations shown are examples only. | - | - |
|
Wax |
|
Anti-chipping Paint |
Under Coat
Acrylic resin is applied to the underside of the body, inside the wheel housing and other parts that are susceptible to stone chipping damage, thus improving the rust-resistant performance of these areas.
| *a | Front Wheel House | *b | Rear Wheel House |
|
Edge Seal |
|
Acrylic Resin Coating Area |
|
Acrylic Resin Coating Area (Thick Coating) | - | - |
Low Vibration and Low Noise Body
A hood insulator is provided on the rear of the hood sub-assembly. This achieves excellent sound insulation performance.
An outer dash panel insulator is provided. These reduce the amount of engine noise leaking into and out of the cabin.
A front fender side panel protector is provided. This prevents road noise from entering the cabin, and achieves superior quietness.
| *1 | Hood Insulator | *2 | Outer Dash Panel Insulator |
| *3 | Front Fender Side Panel Protector | - | - |
To reduce the amount of road noise, engine noise and droning sound that enters the cabin, the floor panel is coated with a vibration damping coat.
|
Spray Type Damping Material Application Area | - | - |
A sound insulation material is used in the body frame profile, thus reducing the various noises which intrude from the outside of the vehicle to the inside of the cabin.
Rocker panel moulding is provided on the underside of the rockers, thus reducing the sound of sand and pebbles thrown up from the road.
| *1 | Rocker Panel Moulding | - | - |
| *a | A-A Cross Section | - | - |
|
Polyurethane Form |
|
Expanded Form |
|
Polyethylene Sealer | - | - |
Parts with Low Repair Cost
A crush box structure is used to reduce body deformation during minor collisions. A structure with screw connections is provided for the front bumper arm sub-assembly to enable easy removal and installation, thus achieving simpler servicing operation and repair cost reduction.
| *1 | Front Bumper Reinforcement | *2 | Front Bumper Arm Sub-assembly |
| *3 | Bolt | - | - |