FUNCTION OF MAIN COMPONENTS
| Components | Function | |
|---|---|---|
| Pre-crash Safety City Sensor | ·
Controls the lane departure alert system. ·
Transmits the indicator illumination request signal and buzzer sound request signal to the combination meter assembly. |
|
·
Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width and distance from markers and heading angle deviation. ·
Transmits an operation signal to the pre-crash safety city heater via the pre-crash safety city heater relay. |
||
| Pre-crash Safety City Heater | Heats the heater pattern area in accordance with the signals from the pre-crash safety city sensor. | |
| Spiral Cable with Sensor Sub-assembly | Steering Sensor | Detects the steering direction and angle of the steering wheel. |
| Airbag Sensor Assembly | Yaw Rate Sensor | Detects yaw rate and transmits a signal to the pre-crash safety city sensor. |
| Speed Sensor | Transmits a vehicle speed signal to the skid control ECU. | |
| Combination Switch Assembly | LDA Switch | Transmits an on/off signal to the pre-crash safety city sensor. |
| Headlight Dimmer Switch Assembly | Transmits a turn signal command to the combination meter assembly. | |
| Combination Meter Assembly | Combination Meter | Transmit the turn signal state to pre-crash safety city sensor. |
| LDA Indicator Light | Indicates whether the LDA system has been turned on using the LDA switch. | |
| LDA Warning Light | Illuminates when there is a system malfunction. | |
| Multi-information Display | Controls the display in response to the display request signal from the pre-crash safety city sensor. | |
| ODO/TRIP DISP Switch | Changes between the odometer and TRIP displays. | |
| Buzzer | Sounds to warn the driver of the system condition in accordance with signals from the pre-crash safety city sensor. | |
| ECM | Transmits the reverse signal to the pre-crash safety city sensor. | |
| Brake Actuator Assembly | Skid Control ECU | Sends a vehicle speed signal from the speed sensor to the pre-crash safety city sensor. |
| Main Body ECU (Multiplex Network Body ECU) | Sends country specification information signals to the pre-crash safety city sensor. | |
OPERATING CONDITION
Operating Conditions of Lane Departure Alert System
| Operation | Condition |
|---|---|
| Operating/Resume | The lane departure alert system is activated when all of the following conditions are met:
·
The LDA switch is on. (When the LDA switch is pressed to turn on the lane departure alert system, the LDA indicator light illuminates.) ·
The vehicle speed is approximately 50 km/h (32 mph) or more. ·
Lane markers are detected. ·
No turn signal command is detected. ·
System malfunction is not detected. |
| Suspended | The lane departure alert system is suspended when any one of the following conditions is met:
·
The vehicle speed is lower than 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers are detected. ·
The temperature of the pre-crash safety city sensor is abnormal. ·
Immediately after the lane departure alert is activated. |
| Canceled | The lane departure alert system is stopped when any one of the following conditions is met:
·
The LDA switch is off. ·
The lane departure alert system is malfunctioning. |
| The lane departure alert system resumes when the following conditions are met:
·
The conditions to start operation listed above are satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch turned off and ON again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. |
Changing lane departure alert sensitivity
By operating the ODO/TRIP DISP switch, the sensitivity of the lane departure alert system as shown on the multi-information display in the combination meter assembly can be changed.
| *a | Sensitivity Level: High | *b | Sensitivity Level: Standard |
CONSTRUCTION
Pre-crash Safety City Sensor
The pre-crash safety city sensor captures a road image up to approximately 50 m (164 ft.) ahead of the camera.
The pre-crash safety city sensor detects lane markers and calculates the radius to the center of the lane, the vehicle center position disparity among the distances from each left and right lane marker and the angle disparity between the vehicle traveling direction and each left and right lane marker.
When one of the following operations is conducted, the pre-crash safety city sensor angle must be adjusted. For details, refer to the Repair Manual.
The pre-crash safety city sensor is removed and reinstalled or replaced.
Parts relating to the tires or suspension are replaced or adjusted.
Excessive force is applied to the pre-crash safety city sensor.
The pre-crash safety city sensor calculates the estimated position which the front wheel will reach based on the information collected, vehicle speeds and front wheel positions. When the pre-crash safety city sensor determines that the front wheel is about to cross the lane marker, the pre-crash safety city sensor activates the lane departure alert system, displays a warning indicator on the combination meter assembly and sounds the buzzer.
The lane departure alert system does not operate if the vehicle approaches the lane marker at a shallow angle, but does not cross it.
| *1 | Pre-crash Safety City Sensor | - | - |
| *a | Monocular Camera Sensor | *b | Image Processing Range |
| *c | Approximately 50 m (164 ft.) | *d | Lane Marker |
| *e | Approximately 3.0 m (9.8 ft.) or more | - | - |
| *a | Image Captured by Pre-crash Safety City Sensor | *b | Left Lane Marker |
| *c | Center of Lane | *d | Right Lane Marker |
| *e | Angle between the vehicle traveling direction and right lane marker. | *f | Distance from the center of vehicle to right lane marker. |
| *g | Distance from the center of vehicle to left lane marker. | *h | Angle between the vehicle traveling direction and left lane marker. |
| *i | Lane Radius (If only the left lane marker or right lane marker is recognized, the radius of the recognized lane marker will be calculated.) | - | - |
Pre-crash Safety City Heater
The pre-crash safety city heater, which is installed between the pre-crash safety city sensor and windshield glass, is heated in the heater pattern area according to signals from the pre-crash safety city sensor in order to prevent the windshield glass on the front of the pre-crash safety city sensor from fogging, and also to remove fog buildup.
OPERATION
Combination Meter Assembly
Information and alerts regarding the status of the lane departure alert (LDA) system are communicated by the LDA indicator light, LDA warning light and multi-information display in the combination meter assembly, and by the sounding of the buzzer.
| *a | LDA Indicator Light | *b | LDA Warning Light |
| *c | Multi-information Display | - | - |
The operating condition of the lane departure alert system is shown by lane marker indicators on the multi-information display.
| Lane Marker Status | Control Status | Multi-information Display Indicators |
|---|---|---|
|
*: Thin or thick likes are displayed independently for the left and right sides depending on whether lane markers are detected on that side. |
||
| None Displayed | LDA switch is off | - |
| Thin Lines Displayed | Lane Departure Alert system is not currently monitoring for lane departure* |
|
| Thick Lines Displayed | Lane Departure Alert system is currently monitoring for lane departure* |
|
Based on the driver's switch operations and the road conditions, the multi-information display will appear as follows.
| LDA switch | Lane Marker Detection Status | Control Status | Multi-information Display Indicators |
|---|---|---|---|
| OFF | - | - | - |
| ON | Detected | Lane markers detected on both sides |
|
| ON | Detected | Lane markers detected on one side only |
|
| ON | Detected | Lane departure alert activated |
|
| Thick line flashes and lane departure alert buzzer sounds |
When there is a system malfunction or the lane departure alert function is suspended, the following warning indications are shown in the combination meter assembly.
| Status Displayed | Suspected Conditions | LDA Indicator Light | LDA Warning Light |
|---|---|---|---|
|
*: Displayed only once per driving cycle. |
|||
| LDA Malfunction Display | System malfunction detected | Turns off | Turns on |
| Vehicle speed below approximately 50 km/h (32 mph) | ·
During LDA system operation, the vehicle speed decreased to less than the minimum speed required for operation.* ·
The LDA switch was turned on while the vehicle speed was less than the minimum speed required for operation. |
Turns on | Turns off |
DIAGNOSIS
If a malfunction is detected in the lane departure alert system, the pre-crash safety city sensor cancels the lane departure alert system, illuminates the LDA warning light in yellow in the combination meter assembly to inform the driver of the malfunction.
The malfunction is stored in memory as a Diagnostic Trouble Code (DTC). When a Global TechStream (GTS) is connected to the DLC3, the DTC can be read. For details, refer to the Repair Manual.