Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0110  Intake Air Temperature Circuit Malfunction  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A357211E02
0.125,0.063 0.656,0.25 0.531,0.188 10 false Fig. 1: 0.115,0.333 0.979,0.542 0.865,0.208 10 false Resistance 0.313,0.604 0.698,0.792 0.385,0.188 10 false (kΩ) 0.156,0.76 0.385,0.938 0.229,0.177 10 false 30 0.156,0.979 0.375,1.146 0.219,0.167 10 false 20 0.177,1.292 0.396,1.458 0.219,0.167 10 false 10 0.25,1.667 0.396,1.854 0.146,0.188 10 false 5 0.25,1.906 0.375,2.083 0.125,0.177 10 false 3 0.26,2.135 0.385,2.313 0.125,0.177 10 false 2 0.25,2.448 0.385,2.625 0.135,0.177 10 false 1 0.135,3.635 0.406,3.802 0.271,0.167 10 false 0.1 0.115,3.281 0.375,3.448 0.26,0.167 10 false 0.2 0.115,3.083 0.375,3.25 0.26,0.167 10 false 0.3 0.115,2.833 0.375,3 0.26,0.167 10 false 0.5 0.458,4.01 0.729,4.177 0.271,0.167 10 false -20 0.927,4.01 1.198,4.177 0.271,0.167 10 false 0 1.26,4.01 1.49,4.188 0.229,0.177 10 false 20 1.635,4.01 1.865,4.188 0.229,0.177 10 false 40 2.021,4.01 2.25,4.188 0.229,0.177 10 false 60 2.417,4.021 2.646,4.198 0.229,0.177 10 false 80 2.771,4.021 3.042,4.198 0.271,0.177 10 false 100 3.073,4.01 3.385,4.219 0.313,0.208 10 false (°C) 0.521,4.167 0.792,4.333 0.271,0.167 10 false -4 0.896,4.156 1.167,4.323 0.271,0.167 10 false 32 1.26,4.167 1.531,4.333 0.271,0.167 10 false 68 1.604,4.167 1.917,4.333 0.313,0.167 10 false 104 1.979,4.167 2.292,4.333 0.313,0.167 10 false 140 2.375,4.188 2.688,4.354 0.313,0.167 10 false 176 2.781,4.188 3.094,4.354 0.313,0.167 10 false 212 3.083,4.198 3.396,4.406 0.313,0.208 10 false (°F) 1.531,4.354 2.396,4.563 0.865,0.208 10 false Temperature

The intake air temperature sensor, mounted in the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R which is located inside the ECM.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.

HINT:

When any of DTCs P0110, P0112 and P0113 are stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0110 Open or short in intake air temperature circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


P0112 Short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


P0113 Open in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM



HINT:

When any of these DTCs are stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit and stores DTC P0113. Conversely, if the output voltage is below 0.14 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit and stores DTC P0112.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0110, P0112 or P0113.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A254076E05
5.073,1.583 5.385,1.792 0.313,0.208 10 false B84 5.073,2.177 5.406,2.365 0.333,0.188 10 false B84 5.875,3.104 6.302,3.292 0.427,0.188 10 false ECM 5.427,1.458 5.792,1.656 0.365,0.198 10 false THA 5.427,2.052 5.906,2.229 0.479,0.177 10 false ETHA 5.115,1.385 5.365,1.542 0.25,0.156 10 false 65 5.104,1.979 5.354,2.167 0.25,0.188 10 false 88 1.99,1.417 2.094,1.552 0.104,0.135 10 false 4 1.99,2.021 2.083,2.177 0.094,0.156 10 false 5 1.708,2.021 1.927,2.167 0.219,0.146 10 false E2 1.615,1.406 1.927,1.552 0.313,0.146 10 false THA 0.26,2.813 0.688,2.99 0.427,0.177 10 false B72 0.26,2.958 2.271,3.354 2.01,0.396 10 false Intake Air Temperature Sensor (built into Mass Air Flow Meter) 6.021,1.063 6.302,1.229 0.281,0.167 10 false 5 V 6.021,1.344 6.156,1.531 0.135,0.188 10 false R

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


e.

Read the value displayed on the tester.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).


·

If there is a short circuit, the tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.

Check the connection and terminal contact pressure of connectors and wire harness between the mass air flow meter and ECM.


b.
U158106E02
1.938,3.573 1.625,4.219 false 2.167,3.563 2.521,4.219 false 0.698,1.833 0.927,2.042 0.229,0.208 10 false *1 2.75,2.26 2.938,2.469 0.188,0.208 10 false *2 0.271,3.354 0.604,3.563 0.333,0.208 10 false B72 0.365,2.896 0.563,3.083 0.198,0.188 10 false *a 1.521,4.24 2.01,4.438 0.49,0.198 10 false THA 2.542,4.26 2.833,4.438 0.292,0.177 10 false E2 2.417,1.823 2.833,2.01 0.417,0.188 10 false ETHA 2.417,1.385 2.833,1.573 0.417,0.188 10 false THA

Disconnect the mass air flow meter connector.


c.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


d.

Connect the intelligent tester to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the tester on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


h.

Read the value displayed on the tester.

Standard value:

140°C (284°F)


Text in Illustration
*1 Mass air flow meter
*2 ECM
*a Front view of wire harness connector
(to Mass air flow meter)



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-4 (THA) - B84-65 (THA) Always Below 1 Ω
B72-5 (E2) - B84-88 (ETHA) Always Below 1 Ω




OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A260197E02
0.7,1.756 0.954,1.912 0.253,0.156 10 *1 2.499,1.756 2.766,1.931 0.267,0.174 10 *2 2.217,1.262 2.609,1.420 0.392,0.158 10 ETHA 2.217,0.864 2.614,1.043 0.397,0.179 10 THA

Disconnect the mass air flow meter connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value displayed on the tester.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Mass air flow meter
*2 ECM



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-4 (THA) or B84-65 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR