Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM J

2NZ-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal is input to the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates. While the NE signal is input to the ECM with the engine running, the ECM turns the Tr1 on continuously.

WIRING DIAGRAM

A254129E04
2.542,0.698 2.927,0.885 0.385,0.188 10 false AM2 0.438,1.49 0.844,1.688 0.406,0.198 10 false AM2 0.448,2.979 0.969,3.167 0.521,0.188 10 false MAIN 1.344,4.448 1.625,4.635 0.281,0.188 10 false 1E 1.344,3.635 1.604,3.792 0.26,0.156 10 false 1E 4.708,3.635 4.969,3.854 0.26,0.219 10 false 1D 4.719,2.469 5.021,2.667 0.302,0.198 10 false 1D 4.719,5.396 4.969,5.604 0.25,0.208 10 false 1E 4.719,4.458 4.99,4.625 0.271,0.167 10 false 1E 1.344,2.125 1.615,2.302 0.271,0.177 10 false 1C 5.781,5.229 5.885,5.375 0.104,0.146 10 false 7 5.729,3.458 5.906,3.604 0.177,0.146 10 false 44 4.74,5.229 4.917,5.375 0.177,0.146 10 false 11 4.781,4.281 4.875,4.427 0.094,0.146 10 false 4 4.781,3.458 4.885,3.604 0.104,0.146 10 false 7 4.74,2.281 4.917,2.427 0.177,0.146 10 false 17 1.354,3.448 1.552,3.615 0.198,0.167 10 false 10 1.385,4.26 1.49,4.406 0.104,0.146 10 false 5 1.396,1.927 1.573,2.073 0.177,0.146 10 false 1 2.865,3.948 3.5,4.104 0.635,0.156 10 false EFI MAIN 2.125,3.438 2.76,3.594 0.635,0.156 10 false EFI MAIN 4.448,3 4.698,3.146 0.25,0.146 10 false IG2 3.323,0.708 3.646,0.885 0.323,0.177 10 false IG2 3.073,2.771 3.323,2.917 0.25,0.146 10 false IG2 6.271,6.375 6.604,6.521 0.333,0.146 10 false ECM 2.927,5.104 3.406,5.25 0.479,0.146 10 false C/OPN 3.656,0.708 3.76,0.854 0.104,0.146 10 false 6 2.385,0.708 2.49,0.854 0.104,0.146 10 false 5 0.594,6.448 1.063,6.594 0.469,0.146 10 false Battery 1.469,6.906 2.302,7.115 0.833,0.208 10 false Fuel Pump 2.396,1.313 3.979,1.458 1.583,0.146 10 false Ignition Switch Assembly 2.375,5.75 3.896,5.927 1.521,0.177 10 false No. 1 Integration Relay 5.677,5.396 5.979,5.563 0.302,0.167 10 false A74 5.688,3.625 6.021,3.813 0.333,0.188 10 false A74 5.688,4.083 6.021,4.281 0.333,0.198 10 false A74 6.031,5.25 6.313,5.448 0.281,0.198 10 false FC 6.031,4.469 6.438,4.625 0.406,0.156 10 false +B 6.031,4.083 6.438,4.24 0.406,0.156 10 false +B2 6.031,3.646 6.438,3.802 0.406,0.156 10 false MREL 2.396,1.167 2.698,1.333 0.302,0.167 10 false F13 1.469,6.75 1.771,6.948 0.302,0.198 10 false K17 1.375,6.01 1.49,6.198 0.115,0.188 10 false 4 2.167,6.01 2.292,6.198 0.125,0.188 10 false 5 6.573,5.302 6.833,5.5 0.26,0.198 10 false Tr1 5.698,4.458 6.042,4.635 0.344,0.177 10 false A74 5.76,3.906 5.938,4.104 0.177,0.198 10 false 1 5.771,4.271 5.927,4.469 0.156,0.198 10 false 2 0.729,2.302 1.01,2.5 0.281,0.198 10 false R/I

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPD)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel pump/Speed.


e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.


Result
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B


A

2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)

B

6.READ VALUE USING INTELLIGENT TESTER (STARTING SIGNAL)
2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)
a.

Inspect the No. 1 integration relay (C/OPN relay) (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1E-11 - A74-7 (FC) Always Below 1 Ω
1E-11 or A74-7 (FC) - Body ground Always 10 kΩ or higher



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-5 - K17-4 Always Below 1 Ω
K17-5 - Body ground Always Below 1 Ω
1E-5 or K17-4 - Body ground Always 10 kΩ or higher




OK

5.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP
a.


OK

NG

6.READ VALUE USING INTELLIGENT TESTER (STARTING SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the tester when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

7.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

7.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


e.

Read the values displayed on the tester while cranking.

OK:

Values are displayed continuously.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR