These DTCs indicate malfunctions relating to the primary circuit.
If DTC P0351 is stored, check the No. 1 ignition coil (No. 1 cylinder) circuit.
If DTC P0352 is stored, check the No. 1 ignition coil (No. 2 cylinder) circuit.
If DTC P0353 is stored, check the No. 1 ignition coil (No. 3 cylinder) circuit.
If DTC P0354 is stored, check the No. 1 ignition coil (No. 4 cylinder) circuit.
A direct ignition system is used on this vehicle.
The direct ignition system is an ignition system in which each cylinder is ignited by its own No. 1 ignition coil and spark plug. The secondary wiring of each No. 1 ignition coil generates a powerful voltage which is applied directly to each spark plug. The spark passes from the center electrode of the spark plug to the ground electrode.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0351
P0352 P0353 P0354 |
No IGF signal to ECM while engine running
(1 trip detection logic) |
·
Ignition system ·
Open or short in IGF1 or IGT (1 to 4) circuit between No. 1 ignition coil and ECM ·
No. 1 ignition coil (No.1 to No. 4 cylinder) ·
ECM |
Reference: Inspection using an oscilloscope
While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
| ECM Terminal Name | CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1 |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
| Required Sensors/Components (Main) | No. 1 ignition coil |
| Required Sensors/Components (Related) | ECM |
| Frequency of Operation | Continuous |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Idle the engine for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
If a DTC is output, the system is malfunctioning.
If a DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0351, P0352, P0353 or P0354.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform Confirmation Driving Pattern and the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the No. 1 ignition coil connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B13-4 (GND) - Body ground | Always | Below 1 Ω |
| B15-4 (GND) - Body ground | Always | Below 1 Ω |
| B17-4 (GND) - Body ground | Always | Below 1 Ω |
| B19-4 (GND) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the No. 1 ignition coil connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B13-1 (+B) - B13-4 (GND) | Ignition switch ON | 11 to 14 V |
| B15-1 (+B) - B15-4 (GND) | Ignition switch ON | 11 to 14 V |
| B17-1 (+B) - B17-4 (GND) | Ignition switch ON | 11 to 14 V |
| B19-1 (+B) - B19-4 (GND) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to No. 1 Ignition Coil) |
OK
NG
Disconnect the No. 1 ignition coil connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B13-2 (IGF) - B84-81 (IGF1) | Always | Below 1 Ω |
| B15-2 (IGF) - B84-81 (IGF1) | Always | Below 1 Ω |
| B17-2 (IGF) - B84-81 (IGF1) | Always | Below 1 Ω |
| B19-2 (IGF) - B84-81 (IGF1) | Always | Below 1 Ω |
| B13-3 (IGT1) - B84-85 (IGT1) | Always | Below 1 Ω |
| B15-3 (IGT2) - B84-84 (IGT2) | Always | Below 1 Ω |
| B17-3 (IGT3) - B84-83 (IGT3) | Always | Below 1 Ω |
| B19-3 (IGT4) - B84-82 (IGT4) | Always | Below 1 Ω |
| B13-2 (IGF), B15-2 (IGF), B17-2 (IGF), B19-2 (IGF) or B84-81 (IGF1) - Body ground | Always | 10 kΩ or higher |
| B13-3 (IGT1) or B84-85 (IGT1) - Body ground | Always | 10 kΩ or higher |
| B15-3 (IGT2) or B84-84 (IGT2) - Body ground | Always | 10 kΩ or higher |
| B17-3 (IGT3) or B84-83 (IGT3) - Body ground | Always | 10 kΩ or higher |
| B19-3 (IGT4) or B84-82 (IGT4) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Shuffle arrangement of the No. 1 ignition coil (among No. 1 to No. 4 cylinders).
Do not shuffle the connectors.
Start the engine and run it at idle for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Same DTC is output | A |
| Different No. 1 ignition coil DTC is output | B |
A
B
Disconnect the No. 1 ignition coil connectors.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B13-1 (+B) - 1E-2 | Always | Below 1 Ω |
| B15-1 (+B) - 1E-2 | Always | Below 1 Ω |
| B17-1 (+B) - 1E-2 | Always | Below 1 Ω |
| B19-1 (+B) - 1E-2 | Always | Below 1 Ω |
| B13-1 (+B) or 1E-2 - Body ground | Always | 10 kΩ or higher |
| B15-1 (+B) or 1E-2 - Body ground | Always | 10 kΩ or higher |
| B17-1 (+B) or 1E-2 - Body ground | Always | 10 kΩ or higher |
| B19-1 (+B) or 1E-2 - Body ground | Always | 10 kΩ or higher |
OK
NG