Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0657  Actuator Supply Voltage Circuit / Open  


DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the ignition switch is turned off. If the output voltage is higher than 7 V when the ignition switch is turned off, the ECM will illuminate the MIL and store a DTC when the ignition switch is turned to ON.

DTC No. DTC Detection Condition Trouble Area
P0657 There is a throttle actuator power supply error (1 trip detection logic). ECM

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Throttle actuator power supply voltage 7 V or more

TYPICAL MALFUNCTION THRESHOLDS

Ignition switch from ON to off (Temporary Fail ON)
Electronic throttle actuator power supply ON

CONFIRMATION DRIVING PATTERN

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the tester off.

5.

Turn the ignition switch off.

6.

Disconnect the tester.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Connect the tester to the DLC3.

10.

Turn the ignition switch to ON.

11.

Wait 10 seconds or more.

12.

Turn the ignition switch off and wait 15 seconds or more.

13.

Turn the ignition switch to ON and turn the intelligent tester on.

14.

Wait 5 seconds or more.

15.

Enter the following menus: Powertrain / Engine and ECT / DTC.

16.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P0657.

19.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK FOR DTC (DTC P0657)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the tester off.


f.

Turn the ignition switch off.


g.

Disconnect the tester.


h.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


i.

Connect the cable to the negative (-) battery terminal.


j.

Turn the ignition switch to ON.


k.

Wait 10 seconds or more.


l.

Turn the ignition switch off.


m.

Wait 15 seconds or more.


n.

Connect the tester to the DLC3.


o.

Turn the ignition switch to ON and turn the tester on.


p.

Wait 5 seconds or more.


q.

Enter the following menus: Powertrain / Engine and ECT / DTC.


r.

Read DTCs.

OK:

P0657 is not output.




OK

NG