Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P2111  Throttle Actuator Control System - Stuck Open  P2112  Throttle Actuator Control System - Stuck Closed  


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using an electric motor and gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This electronic throttle control system does not use a throttle cable.

DTC No. DTC Detection Condition Trouble Area
P2111 ECM signals throttle actuator to close, but the actuator is stuck
(1 trip detection logic)
·

Throttle actuator

·

Throttle with motor body assembly

·

Throttle valve

·

ECM

·

Wire harness or connector


P2112 ECM signals throttle actuator to open, but the actuator is stuck
(1 trip detection logic)
·

Throttle actuator

·

Throttle with motor body assembly

·

Throttle valve

·

ECM

·

Wire harness or connector




MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components Throttle with motor body assembly
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

ALL:
Throttle actuator ON
Throttle actuator duty calculation Executing
Throttle position sensor fail Not detected
Throttle actuator current-cut operation Not executing
Throttle actuator power supply 4 V or higher
Throttle actuator fail Not detected

P2111 (Throttle actuator stuck open)
All of following conditions met -
Throttle actuator current 2 A or higher
Duty cycle to close throttle 80% or more

P2112
All of following conditions met -
Throttle actuator current 2 A or higher
Duty cycle to open throttle 80% or more

TYPICAL MALFUNCTION THRESHOLDS

Throttle position sensor voltage No change

CONFIRMATION DRIVING PATTERN

A199314E14
0.106,0.049 1.616,0.222 1.510,0.174 10 Accelerator Pedal State 0.922,0.387 1.650,0.536 0.728,0.149 10 Depressed 0.936,0.871 1.578,1.027 0.642,0.156 10 Released 1.211,2.321 1.596,2.508 0.385,0.187 10 Idling 0.404,2.608 1.608,2.778 1.205,0.170 10 Ignition Switch ON 2.078,2.699 2.276,2.883 0.198,0.184 10 [A] 4.4,3.427 4.591,3.604 0.191,0.177 10 [B]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

7.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2111 or P2112.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



12.

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again and, if necessary, drive the vehicle for a period of time.


FAIL-SAFE

When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.

Result
Result Proceed to
P2111 or P2112 is output A
P2111 or P2112 and other DTCs are output B

HINT:

If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.




A

2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

B

2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing. If necessary, clean the throttle with motor body assembly. Then check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.




OK

3.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

NG

5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
3.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.


h.

Read the values displayed on the tester while wiggling the ECM wire harness.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.


j.

Read DTCs.

Result
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B



A

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)

B

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).



NEXT

END

5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.


j.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC P2111 or P2112 is output B



A

END

B