Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This electronic throttle control system does not use a throttle cable.

·

These DTCs relate to the accelerator pedal position sensor.



The accelerator pedal position sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme conditions. The voltage from this sensor, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal operating angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A256706E03
0.175,1.352 0.656,1.533 0.480,0.181 10 Magnet 1.562,1.272 2.089,1.454 0.526,0.181 10 IC No. 1 0.311,3.318 0.837,3.499 0.526,0.181 10 IC No. 2 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,3.98 3.018,4.161 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.415,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 13.1 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.677,3.877 6.634,4.079 1.957,0.202 10 Accelerator Pedal Angle (°) 4.369,4.736 6.648,4.918 2.279,0.181 10 *1: Accelerator Pedal Fully Released 4.369,5.044 6.756,5.210 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 1.025,3.771 1.506,3.952 0.480,0.181 10 Magnet 0.843,2.878 0.554,3.289 false 0.965,3.195 1.207,3.756 false 1.067,2.576 1.539,1.374 false 0.967,2.293 0.695,1.429 false 2.188,0.799 3.881,1.455 1.693,0.656 10 Accelerator Pedal Position Sensor Output Voltage (V) 0.283,4.078 1.976,4.618 1.693,0.540 10 Accelerator Pedal Sensor Assembly 4.355,1.841 3.869,0.944 false

DTC No. DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

ECM


P2122 VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


P2123 VPA is 4.8 V or more for 2.0 seconds or more
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

ECM


P2125 VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

ECM


P2127 VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


P2128 Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or more
(b) VPA is between 0.4 V and 3.45 V
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

ECM


P2138 Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
·

Short between VPA and VPA2 circuits

·

Accelerator pedal sensor assembly

·

ECM



HINT:

When any of these DTCs are stored, check the accelerator pedal position sensor voltage by entering the following menus using the intelligent tester: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area Accelerator Pedal Released Accelerator Pedal Depressed
Accel Sensor Out No. 1 Accel Sensor Out No. 2 Accel Sensor Out No. 1 Accel Sensor Out No. 2
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.7 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.7 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA drops below 0.4 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal position sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

VPA voltage 0.5 V to 4.5 V
VPA2 voltage 1.2 V to 4.7 V
Difference between VPA and VPA2 voltages more than 0.05 V

CONFIRMATION DRIVING PATTERN

A199317E01
0.12,0.098 1.732,0.272 1.611,0.174 10 Accelerator Pedal State 0.865,0.418 1.583,0.567 0.719,0.149 10 Depressed 0.95,0.878 1.592,1.034 0.642,0.156 10 Released 0.432,2.405 1.636,2.575 1.205,0.170 10 Ignition Switch ON 2.092,2.489 2.290,2.673 0.198,0.184 10 [A] 4.414,3.434 4.632,3.611 0.218,0.177 10 [C] 5.364,1.69 6.006,1.846 0.642,0.156 10 Released 2.877,3.049 3.553,3.226 0.677,0.177 10 5 seconds 3.006,1.226 3.725,1.375 0.719,0.149 10 Depressed 3.868,1.129 4.058,1.306 0.191,0.177 10 [B] 3.634,2.007 2.767,1.303 2.767,1.303 2.93,1.303 false 4.728,2.416 5.116,1.774 5.116,1.774 5.261,1.774 false 2.59,2.008 3.232,2.164 0.642,0.156 10 Released 2.207,2.416 2.44,2.073 2.44,2.073 2.543,2.073 false

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.




FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A254093E02
0.396,2.885 0.719,3.083 0.323,0.198 10 false A36 1.552,0.365 1.917,0.542 0.365,0.177 10 false VPA 1.531,0.802 1.906,1 0.375,0.198 10 false EPA 1.438,1.219 1.906,1.438 0.469,0.219 10 false VCPA 1.49,1.646 1.917,1.844 0.427,0.198 10 false VPA2 1.49,2.073 1.927,2.271 0.438,0.198 10 false EPA2 1.49,2.5 1.927,2.698 0.438,0.198 10 false VCP2 5.583,0.219 5.896,0.375 0.313,0.156 10 false VPA 5.583,0.906 5.969,1.083 0.385,0.177 10 false EPA 5.583,1.104 5.99,1.25 0.406,0.146 10 false VCPA 5.583,1.5 5.99,1.646 0.406,0.146 10 false VPA2 5.583,2.167 6.031,2.365 0.448,0.198 10 false EPA2 5.583,2.375 6.042,2.604 0.458,0.229 10 false VCP2 2,0.26 2.115,0.427 0.115,0.167 10 false 6 2,0.677 2.115,0.854 0.115,0.177 10 false 5 2,1.083 2.104,1.25 0.104,0.167 10 false 4 2,1.5 2.104,1.667 0.104,0.167 10 false 3 2,1.938 2.115,2.104 0.115,0.167 10 false 2 2,2.313 2.115,2.469 0.115,0.156 10 false 1 5.292,0.208 5.49,0.385 0.198,0.177 10 false 55 5.302,0.625 5.49,0.802 0.188,0.177 10 false 59 5.302,1.042 5.542,1.24 0.24,0.198 10 false 57 5.292,1.469 5.49,1.615 0.198,0.146 10 false 56 5.292,1.885 5.479,2.052 0.188,0.167 10 false 60 5.292,2.313 5.5,2.5 0.208,0.188 10 false 58 6.01,2.906 6.365,3.063 0.354,0.156 10 false ECM 5.25,2.5 5.552,2.708 0.302,0.208 10 false A74 5.24,2.073 5.552,2.24 0.313,0.167 10 false A74 5.25,1.229 5.573,1.479 0.323,0.25 10 false A74 5.25,0.406 5.583,0.594 0.333,0.188 10 false A74 5.25,1.646 5.594,1.813 0.344,0.167 10 false A74 5.24,0.833 5.563,1.042 0.323,0.208 10 false A74 6.323,0.958 6.583,1.104 0.26,0.146 10 false 5 V 6.333,2.229 6.594,2.375 0.26,0.146 10 false 5 V 0.396,3.052 2.74,3.24 2.344,0.188 10 false Accelerator Pedal Sensor Assembly

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the accelerator pedal position sensor.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR)
A160308E03
0.806,1.751 1.044,1.911 0.239,0.161 10 *b 2.395,1.751 2.616,1.911 0.221,0.161 10 *c 1.434,0.233 1.673,0.393 0.239,0.161 10 *a

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the values displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2 Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V More than 0.02 V
Depressed 2.6 to 4.5 V 3.4 to 4.7 V


Text in Illustration
*a Accelerator Pedal
*b Depressed
*c Released


Result
Result Proceed to
NG A
OK B


A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-6 (VPA) - A74-55 (VPA) Always Below 1 Ω
A36-5 (EPA) - A74-59 (EPA) Always Below 1 Ω
A36-4 (VCPA) - A74-57 (VCPA) Always Below 1 Ω
A36-3 (VPA2) - A74-56 (VPA2) Always Below 1 Ω
A36-2 (EPA2) - A74-60 (EPA2) Always Below 1 Ω
A36-1 (VCP2) - A74-58 (VCP2) Always Below 1 Ω
A36-6 (VPA) or A74-55 (VPA) - Body ground Always 10 kΩ or higher
A36-5 (EPA) or A74-59 (EPA) - Body ground Always 10 kΩ or higher
A36-4 (VCPA) or A74-57 (VCPA) - Body ground Always 10 kΩ or higher
A36-3 (VPA2) or A74-56 (VPA2) - Body ground Always 10 kΩ or higher
A36-2 (EPA2) or A74-60 (EPA2) - Body ground Always 10 kΩ or higher
A36-1 (VCP2) or A74-58 (VCP2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
a.
U158090E01
0.092,0.062 0.265,0.249 0.173,0.187 10 *a 0.357,0.985 0.638,1.146 0.281,0.161 10 A36 1.733,1.808 2.144,1.964 0.411,0.156 10 VCPA 1.069,1.808 1.459,1.945 0.390,0.137 10 EPA2 2.347,1.533 2.649,1.694 0.302,0.162 10 EPA 0.601,1.533 1.005,1.676 0.404,0.144 10 VCP2 0.841,1.51 1.324,1.105 false 1.321,1.775 1.486,1.108 false 1.971,1.792 1.79,1.108 false 2.461,1.505 1.94,1.108 false

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-4 (VCPA) - A36-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A36-1 (VCP2) - A36-2 (EPA2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the tester on.


f.

Fully depress and release the accelerator pedal.


g.

Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.


i.

Read the DTCs.

Result
Result Proceed to
DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output A
DTC is not output B



A

B

END