Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE UNIT
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248080 ENGINE UNIT G

2NZ-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT CHAIN SUB-ASSEMBLY

A369996E04
1.583,1.208 1.896,1.406 0.313,0.198 10 false *a 1.021,1.865 1.177,2.063 0.156,0.198 10 false 2 1.177,1.865 1.333,2.063 0.156,0.198 10 false 3 1.323,1.865 1.479,2.063 0.156,0.198 10 false 4 0.854,1.865 1.01,2.063 0.156,0.198 10 false 1 0.698,1.865 0.854,2.063 0.156,0.198 10 false 0 1.49,1.865 1.646,2.063 0.156,0.198 10 false 5 2.688,1.854 2.885,2.052 0.198,0.198 10 false 16

a.

Using a spring scale, apply 140 N (14.3 kgf, 31.5 lb) to the timing chain and measure its length.

Text in Illustration
*a Measuring Area

Maximum chain elongation:

123.2 mm (4.850 in.)


If the elongation is greater than the maximum, replace the chain.

HINT:

Perform the same measurement at 3 or more random places and calculate the average length.



Hide 13540 2.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

A011223

a.

Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.


b.

Release the ratchet pawl and check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.


Hide 13050 3.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

A037071

a.

Wrap the chain around the camshaft timing gear.


b.

Using a vernier caliper, measure the diameter of the camshaft timing gear with the chain.

Minimum gear diameter (with chain):

96.2 mm (3.787 in.)


If the diameter is less than the minimum, replace the camshaft timing gear.

NOTICE:

Make sure that the vernier caliper is in contact with the chain link when measuring.



Hide 13523 4.INSPECT CAMSHAFT TIMING SPROCKET

A037072

a.

Wrap the chain around the camshaft timing sprocket.


b.

Using a vernier caliper, measure the diameter of the camshaft timing sprocket with the chain.

Minimum gear diameter (with chain):

96.2 mm (3.787 in.)


If the diameter is less than the minimum, replace the camshaft timing sprocket.

NOTICE:

Make sure that the vernier caliper is in contact with the chain link when measuring.



Hide 13559 5.INSPECT CHAIN TENSIONER SLIPPER

A037065

a.

Using a vernier caliper, measure the chain tensioner slipper wear.

Minimum wear:

1.0 mm (0.039 in.)


If the wear is less than the minimum, replace the chain tensioner slipper.


Hide 13561 6.INSPECT NO. 1 CHAIN VIBRATION DAMPER

A037066

a.

Using a vernier caliper, measure the No. 1 chain vibration damper wear.

Minimum wear:

1.0 mm (0.039 in.)


If the wear is less than the minimum, replace the No. 1 chain vibration damper.


Hide 11101A 7.INSPECT CYLINDER HEAD SET BOLT

A098332E07
1.698,0.469 1.896,0.635 0.198,0.167 10 false *a

a.

Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Text in Illustration
*a Measurement Length

Standard length:

142.8 to 144.2 mm (5.6220 to 5.6772 in.)


Maximum length:

147.1 mm (5.7913 in.)


If the bolt length is greater than the maximum, replace the cylinder head set bolt.