Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE UNIT › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248080 ENGINE UNIT A

2NZ-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 15104E 1.INSTALL STUD BOLT

a.

Using "TORX" socket wrench E5, install the 4 stud bolts.

A154885E05
0.448,1.375 0.573,1.531 0.125,0.156 10 false A 1.021,2.313 1.146,2.469 0.125,0.156 10 false B 0.75,2.979 0.875,3.135 0.125,0.156 10 false A 1.469,1.813 1.594,1.969 0.125,0.156 10 false B 5.271,1.354 5.396,1.51 0.125,0.156 10 false A 5.281,3.198 5.406,3.354 0.125,0.156 10 false B 4.531,0.719 5,1.063 0.469,0.344 10 false 22.5 (0.886) 4.521,2.458 4.99,2.802 0.469,0.344 10 false 27.5 (1.083) 5.74,0.573 6.115,0.938 0.375,0.365 10 false 13 (0.51) 5.75,1.01 6.146,1.375 0.396,0.365 10 false 8.0 (0.32) 5.75,2.25 6.219,2.594 0.469,0.344 10 false 16.5 (0.650) 5.771,2.802 6.146,3.167 0.375,0.365 10 false 9.0 (0.35) 6.26,3.354 6.792,3.531 0.531,0.177 10 false mm (in.)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 12101 2.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing material from the contact surface.


b.
A155464E07
1.552,1.875 1.688,2.104 true 0.25,0.833 0.646,1.167 0.396,0.333 10 false 9 (0.35) 0.25,1.563 0.646,1.896 0.396,0.333 10 false 11 (0.43) 2.75,0.938 3.146,1.26 0.396,0.323 10 false 4 (0.16) 2.75,1.427 3.146,1.74 0.396,0.313 10 false 4 (0.16) 1.646,2.115 1.854,2.323 0.208,0.208 10 false *a 2.677,2.344 2.958,2.677 0.281,0.333 10 false mm (in.)

Apply a continuous bead of seal packing ( Diameter 2.0 to 3.0 mm (0.079 to 0.118 in.)) to the oil pan mating surface as shown in the illustration.

Text in Illustration
*a Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Install the oil pan within 3 minutes of applying seal packing.

·

Do not expose the seal to engine oil for at least 2 hours after the installation.




c.

Install 2 new O-rings onto the cylinder block.


d.
A369997E02
0.958,0.583 1.708,1.052 false 1.198,0.573 1.719,1.073 false 1.458,0.573 1.698,1.052 false 1.802,0.458 1.719,1.063 false 2.104,0.604 1.708,1.063 false 2.521,0.604 2.354,1.156 2.354,1.156 2.573,1.708 false 2.875,0.708 2.688,1.156 2.688,1.156 2.875,1.51 false 0.948,1.677 1.208,1.375 1.208,1.375 1.531,1.698 false 1.208,1.375 1.188,1.719 false 1.771,1.302 2.01,1.729 false 1.167,1.188 1.313,1.344 0.146,0.156 10 true B 1.667,1.125 1.823,1.323 0.156,0.198 10 false A 2.198,1.083 2.323,1.281 0.125,0.198 10 true B 2.552,1.052 2.677,1.25 0.125,0.198 10 true C 0.865,0.271 1.021,0.469 0.156,0.198 10 true 5 1.135,0.271 1.292,0.469 0.156,0.198 10 true 4 1.708,0.115 1.906,0.313 0.198,0.198 10 true 15 2.094,0.333 2.25,0.531 0.156,0.198 10 false 2 2.042,0.177 2.24,0.375 0.198,0.198 10 false 14 2.458,0.292 2.656,0.49 0.198,0.198 10 false 13 2.885,0.396 3.083,0.594 0.198,0.198 10 true 12 2.823,1.656 3.021,1.854 0.198,0.198 10 false 11 2.51,1.844 2.708,2.042 0.198,0.198 10 true 10 1.365,0.271 1.521,0.469 0.156,0.198 10 true 3 2.073,1.771 2.229,1.969 0.156,0.198 10 false 1 2.083,1.938 2.229,2.094 0.146,0.156 10 false 9 1.521,1.823 1.677,2.021 0.156,0.198 10 true 8 1.167,1.823 1.323,2.021 0.156,0.198 10 true 7 0.896,1.802 1.052,2 0.156,0.198 10 true 6

Using several steps, install and tighten the 13 bolts uniformly in the sequence shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Each bolt length is as follows:

Bolt A 49 mm (1.93 in.)

Bolt B 88 mm (3.47 in.)

Bolt C 144 mm (5.67 in.)



Hide 15104 3.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer with the 2 nuts and the bolt.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 12102A 4.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove any old packing material from the contact surface.


b.
A081876E09
1.677,0.417 2.323,0.146 false 2.375,0.063 2.552,0.229 0.177,0.167 10 false *a

Apply a continuous bead of seal packing (Diameter 2.5 to 3.5 mm (0.0984 to 0.1378 in.)) to the oil pan mating surface as shown in the illustration.

Text in Illustration
*a Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Install the oil pan within 3 minutes of applying seal packing.

·

Do not expose the seal to engine oil within 2 hours of installation.




c.

Install the No. 2 oil pan with the 9 bolts and the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


d.

Install the drain plug with a new gasket.

Torque:
38 N*m (382 kgf*cm, 28 ft.*lbf)


Hide 15600A 5.INSTALL OIL FILTER UNION

A079679

a.

Using a 12 mm hexagon wrench, install the oil filter union.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 15601 6.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.

Gently screw the oil filter into place, and tighten it until the gasket comes into contact with the seat.


d.
A369995E05
2.073,1.885 2.104,1.708 false 1.979,1.906 2.438,2.104 0.458,0.198 10 false SST

Using SST, tighten it an additional 3/4 turn.

SST
09228-06501  

HINT:

When using a torque wrench, tighten it to the specified torque.


Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 11115 7.INSTALL CYLINDER HEAD GASKET

A371757E02
1.188,0.104 1.5,0.302 0.313,0.198 10 false *a

a.

Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.

Text in Illustration
*a Lot. No.

NOTICE:
·

Pay attention to the mounting orientation of the cylinder head gasket.

·

Do not damage the cylinder gasket when installing the cylinder head onto the cylinder block.




Hide 11101 8.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head bolts are tightened in 2 successive steps.


a.
A381872E01
0.625,0.135 0.771,0.313 0.146,0.177 10 false 8 1.156,0.24 1.302,0.417 0.146,0.177 10 false 4 1.688,0.208 1.833,0.385 0.146,0.177 10 false 2 2.219,0.25 2.365,0.427 0.146,0.177 10 false 5 2.74,0.135 2.885,0.313 0.146,0.177 10 false 9 2.573,1.802 2.719,1.979 0.146,0.177 10 false 7 2.208,1.802 2.354,1.979 0.146,0.177 10 false 3 1.677,1.802 1.823,1.979 0.146,0.177 10 false 1 1.146,1.792 1.292,1.969 0.146,0.177 10 false 6 0.594,1.833 0.781,2.01 0.188,0.177 10 false 10

Apply a light coat of engine oil to the bolt threads and the area beneath the bolt heads that come in contact with the plate washer.


b.

Temporarily install the cylinder head with the 10 cylinder head bolts and 10 plate washers.

NOTICE:

Do not drop the plate washers into the cylinder head.



c.

Using several steps, tighten the 10 cylinder head bolts and 10 plate washers uniformly with an 8 mm bi-hexagon wrench in the sequence shown in the illustration.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


d.
A116959E09
1.406,1.323 1.01,1.563 false 2.771,2.979 2.99,2.76 true 2.208,2.958 2.208,2.646 true 1.698,2.969 1.896,2.646 true 1.156,2.958 1.156,2.656 true 0.594,2.979 0.281,2.75 true 0.594,3.656 0.396,3.885 true 1.167,3.667 1.167,3.948 true 1.667,3.667 1.583,3.938 true 2.208,3.667 2.208,3.938 true 2.771,3.646 3.031,3.865 true 0.938,0.729 1.25,0.906 0.313,0.177 10 false 90° 2.271,0.688 2.583,0.865 0.313,0.177 10 false 90° 0.823,1.49 0.99,1.667 0.167,0.177 10 false *a 0.156,2.667 0.313,2.844 0.156,0.177 10 false 8 1.104,2.458 1.26,2.635 0.156,0.177 10 false 4 1.896,2.469 2.052,2.646 0.156,0.177 10 false 2 2.177,2.438 2.333,2.615 0.156,0.177 10 false 5 3.031,2.646 3.188,2.823 0.156,0.177 10 false 9 0.208,3.844 0.375,4.021 0.167,0.177 10 false 10 1.135,3.979 1.292,4.156 0.156,0.177 10 false 6 1.51,3.958 1.667,4.135 0.156,0.177 10 false 1 2.177,3.958 2.333,4.135 0.156,0.177 10 false 3 3.063,3.844 3.219,4.021 0.156,0.177 10 false 7

Mark the front side of the cylinder head bolts with paint.

Text in Illustration
*a Paint Mark


e.

Retighten the cylinder head bolts an additional 90°, and then once more 90° as shown in the illustration.


f.

Check that the paint mark is now at a 180° angle to the front.


Hide 11401L 9.INSTALL ENGINE REAR OIL SEAL

a.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free of foreign matter.



b.
A166929E06
2.865,1.771 2.656,1.615 false 2.781,1.792 3.115,2 0.333,0.208 10 false SST 1.115,1.917 1.833,2.094 0.719,0.177 10 false 0 to -1 mm 1.083,2.156 1.99,2.354 0.906,0.198 10 false (0 to -0.04 in.)

Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the cylinder block and oil pan.

SST
09223-56010  

NOTICE:
·

Do not tap the oil seal at an angle.

·

Wipe any extra grease off the crankshaft.




Hide 13050 10.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

NOTICE:

Install the camshaft timing gear assembly onto the camshaft with the lock pin of the camshaft timing gear assembly released.


a.

Clamp the camshaft in a vise, and confirm that it is locked.

NOTICE:

Do not damage the camshaft.



b.
A116230E09
1.344,0.906 1.927,0.323 true 1.042,0.969 0.51,1.635 true 1.948,0.198 2.094,0.375 0.146,0.177 10 false *1 0.354,1.625 0.521,1.802 0.167,0.177 10 false *a

Put the camshaft timing gear assembly and camshaft together with the straight pin of the groove.

Text in Illustration
*1 Straight Pin
*a Groove


c.

Turn the camshaft timing gear assembly clockwise while pushing it gently toward the camshaft. When the pin fits into the groove, push to ensure a good fit.

NOTICE:

Do not turn the camshaft timing gear in the retard direction (to the right).



d.

Check that there is no clearance between the gear flange and the camshaft.


e.

Tighten the bolt with the camshaft timing gear fixed.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:
·

Do not lock the camshaft timing gear assembly when tightening the bolt.

·

Release the lock pin of the camshaft timing gear assembly first, and tighten the bolt when the lock pin is locked in the most retarded position.

·

Tightening the bolts with the lock pin locked could cause breakage of the lock pin.




f.

Check that the camshaft timing gear assembly can move in the retard direction (to the right) and is locked in the most retarded position.


Hide 13511 11.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft journals.


b.

Place the camshaft on the cylinder head with the timing mark on the camshaft timing gear facing upward.


c.
A370102E02
1.052,1.938 1.208,2.135 0.156,0.198 10 false 3 1.604,1.938 1.76,2.135 0.156,0.198 10 false 1 2.115,1.927 2.271,2.125 0.156,0.198 10 false 2 2.708,1.927 2.865,2.125 0.156,0.198 10 false 4

Examine the front marks and numbers and tighten the bolts in the sequence shown in the illustration.

Torque:
13 N*m (129 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



Hide 13523 12.INSTALL CAMSHAFT TIMING SPROCKET

A032167

a.

Clamp the camshaft in a vise, and confirm that it is locked.

NOTICE:

Do not damage the camshaft.



b.

Align the knock pin hole the camshaft timing sprocket with the knock pin of the camshaft, and install the camshaft timing sprocket with the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 13512 13.INSTALL NO. 2 CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft journals.


b.

Place the camshaft on the cylinder head with the timing mark on the camshaft timing gear facing upward.


c.
A116223E13
1.167,2.167 0.854,2.594 true 1.49,1.573 2.625,2.604 2.625,2.604 2.792,1.583 true 1.927,1.573 2.625,2.594 2.625,2.594 2.365,1.573 true 1.042,0.208 1.198,0.385 0.156,0.177 10 false 3 1.677,0.198 1.833,0.375 0.156,0.177 10 false 1 2.323,0.198 2.479,0.375 0.156,0.177 10 false 2 2.969,0.198 3.125,0.375 0.156,0.177 10 false 4 0.375,0.958 0.531,1.135 0.156,0.177 10 false 5 2.552,2.625 2.719,2.802 0.167,0.177 10 false *2 0.719,2.604 0.865,2.781 0.146,0.177 10 false *1

Examine the front marks and numbers on the No. 1 and No. 2 camshaft bearing caps and check that the order is as shown in the illustration. Then uniformly tighten the bolts, in several steps, in the sequence shown in the illustration.

Text in Illustration
*1 No. 1 Bearing Cap
*2 No. 2 Bearing Cap

Torque:
No. 2 bearing cap : 13 N*m (129 kgf*cm, 9 ft.*lbf)
No. 1 bearing cap : 23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



Hide 11101E 14.INSTALL CAMSHAFT POSITION SENSOR

A080958

a.

Apply engine oil to the O-ring.

NOTICE:

If the O-ring is damaged, replace the camshaft position sensor.



b.

Install the camshaft position sensor with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 13506 15.INSTALL CHAIN SUB-ASSEMBLY

A381803E01
2.208,4.375 1.802,3.25 true 1.375,0.844 2.5,0.26 2.5,0.26 2.042,0.979 true 2.521,0.146 2.833,0.344 0.313,0.198 10 false *a 2.135,3.177 2.375,3.354 0.24,0.177 10 true 10° 2.25,4.365 2.563,4.563 0.313,0.198 10 false *b

a.

Make sure that all the timing marks are in the positions (TDC) shown in the illustration.

Text in Illustration
*a Timing Marks
*b Timing Mark

HINT:

The positions of the timing marks may differ the predetermined positions due to the force of the valve spring.



b.
A116573E07
1.99,1.052 2.438,0.26 true 2.406,0.094 2.583,0.271 0.177,0.177 10 false *a 1.625,1.833 1.813,2.021 0.188,0.188 10 true *b

Set the timing mark of the crankshaft in a position between 40 and 140° ATDC, as illustrated.

Text in Illustration
*a Timing Mark
*b 40° to 140° ATDC


c.
A381804E01
2.219,4.396 1.719,3.26 true 2.104,0.979 2.646,0.375 2.646,0.375 1.479,0.833 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 2.25,4.385 2.563,4.583 0.313,0.198 10 false *c 2.677,0.26 2.99,0.458 0.313,0.198 10 false *b 2.094,3.25 2.365,3.438 0.271,0.188 10 true 30°

Set the camshaft timing gear and the camshaft timing sprocket in the positions (20° ATDC) shown in the illustration.

Text in Illustration
*a 20° ATDC
*b Timing Mark
*c Timing Marks


d.

Set the crankshaft in the position (20° ATDC) shown in the illustration.


e.
A116576

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


f.
A116577E08
1.188,1.021 2.448,0.198 2.448,0.198 2.052,1.271 true 1.125,1.115 1.094,2.25 1.094,2.25 1.896,1.76 false 1.99,1.417 1.104,2.24 true 1.813,3.719 2.333,2.573 true 1.677,3.75 0.885,4.26 true 2.458,0.073 2.656,0.313 0.198,0.24 10 false *a 2.323,2.417 2.49,2.594 0.167,0.177 10 false *c 0.958,2.24 1.125,2.417 0.167,0.177 10 false *b 0.708,4.208 0.875,4.385 0.167,0.177 10 false *d

Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.

Text in Illustration
*a Mark Plates
*b Timing Marks
*c Mark Plate
*d Timing Mark

HINT:

Align the timing marks with the mark plates while turning the hexagonal service portion of the camshaft using a wrench.



Hide 13559 16.INSTALL CHAIN TENSIONER SLIPPER

A116569

a.

Install the chain tensioner slipper.


Hide 13540 17.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

A116568

a.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.

Remove the bar from the No. 1 chain tensioner assembly.


Hide 15100C 18.INSTALL OIL PUMP SEAL

A166953E10
1.167,2.927 1.354,2.927 false 1.333,1.115 3.021,1.333 1.688,0.219 10 false 0 to - 1 mm (0 to - 0.04 in.) 1.406,2.844 1.708,3 0.302,0.156 10 false SST

a.

Using SST and a hammer, tap in a new oil pump seal until its surface is flush with the timing chain cover.

SST
09950-60010  (09951-00250, 09951-00410, 09952-06010)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the oil seal at an angle.

·

Keep the seal lip free of foreign matter.




b.

Apply MP grease to the oil seal lip.


Hide 15100 19.INSTALL OIL PUMP ASSEMBLY

A116556

a.

Install 2 new O-rings.


b.

Apply seal packing to the oil pump assembly, cylinder head and cylinder block as shown in the illustration.

Seal packing:
Water pump part:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

Other part:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying the seal packing.

·

Do not expose the seal to engine oil for at least 2 hours after the installation.



A264211E04
4.708,1.292 5.302,2.469 5.302,2.469 5.792,1.333 true 2.26,1.781 3.448,2.375 3.448,2.375 2.073,0.99 true 0.563,3.854 1.521,4.198 0.958,0.344 10 false 1.5 to 2.0 (0.059 to 0.079) 2.271,4.156 2.729,4.5 0.458,0.344 10 false 2.5 (0.098) 2.719,4.531 3.177,4.875 0.458,0.344 10 false 1.5 (0.059) 1.083,5.083 1.542,5.438 0.458,0.354 10 false 5.0 (0.197) 2.552,5.094 3.01,5.458 0.458,0.365 10 false 1.5 (0.059) 2.469,6.896 2.917,7.26 0.448,0.365 10 false 2.5 (0.098) 1.281,8.052 1.74,8.396 0.458,0.344 10 false 2.5 (0.098) 5.385,5.406 6.344,5.771 0.958,0.365 10 false 1.5 to 2.0 (0.059 to 0.079) 5.385,4.396 6.344,4.76 0.958,0.365 10 false 3.5 to 4.5 (0.138 to 0.177) 5.385,7.083 6.344,7.458 0.958,0.375 10 false 3.5 to 4.5 (0.138 to 0.177) 5.385,8.354 6.354,8.708 0.969,0.354 10 false 1.5 to 2.0 (0.059 to 0.079) 2.135,8.052 2.594,8.396 0.458,0.344 10 false 1.0 (0.039) 1.031,8.833 1.521,9.177 0.49,0.344 10 false 1.0 (0.039) 2.344,8.75 3.313,9.094 0.969,0.344 10 false 3.5 to 4.5 (0.138 to 0.177) 3.49,2.313 3.677,2.51 0.188,0.198 10 false *a 5.219,2.479 5.406,2.677 0.188,0.198 10 false *a 6.073,9.24 6.604,9.427 0.531,0.188 10 false mm (in.) 4.896,2.813 5.854,3.167 0.958,0.354 10 false 4.5 to 5.5 (0.177 to 0.217) 4.49,3.969 4.677,4.167 0.188,0.198 10 false *b 4.563,6.635 4.74,6.833 0.177,0.198 10 false *c 1.906,3.406 2.229,3.604 0.323,0.198 10 false A-A 1.74,5.865 2.333,6.063 0.594,0.198 10 false B-B, C-C 1.396,1.938 1.51,2.125 0.115,0.188 10 true A 2.542,0.823 2.656,0.979 0.115,0.156 10 false B 1.615,2.76 1.771,2.938 0.156,0.177 10 false C 1.24,1.615 1.365,1.76 0.125,0.146 10 false A 1.833,2.427 1.948,2.594 0.115,0.167 10 true C 3.104,1.125 3.219,1.281 0.115,0.156 10 false B

Text in Illustration
*a Seal Packing *b Seal Width (Other Part)
*c Seal Width (Water Pump Part) - -


c.
A116558

Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.


d.
A116554E04
2.656,0.781 2.813,0.958 0.156,0.177 10 false E 2.583,0.979 2.74,1.156 0.156,0.177 10 false A 2.625,2.146 2.781,2.323 0.156,0.177 10 false B 2.365,2.677 2.521,2.854 0.156,0.177 10 false C 2.5,1.375 2.656,1.552 0.156,0.177 10 false C 0.417,0.208 0.573,0.385 0.156,0.177 10 false D 1.833,3.177 1.99,3.354 0.156,0.177 10 true C 1.344,3.146 1.49,3.365 0.146,0.219 10 true C 1.021,3.115 1.177,3.302 0.156,0.188 10 true C 0.583,2.677 0.74,2.854 0.156,0.177 10 false C 0.458,2.094 0.615,2.271 0.156,0.177 10 false C 0.479,1.74 0.635,1.917 0.156,0.177 10 false C 0.406,1.427 0.563,1.604 0.156,0.177 10 false C 0.396,1.115 0.552,1.292 0.156,0.177 10 false C 0.5,0.729 0.656,0.906 0.156,0.177 10 false A 1.313,1.021 1.469,1.198 0.156,0.177 10 false C

Install the oil pump assembly with the 15 bolts and nut. Tighten the bolts and nut uniformly in several steps.

Torque:
Bolt A : 32 N*m (326 kgf*cm, 24 ft.*lbf)
Bolt B, C : 12 N*m (122 kgf*cm, 9 ft.*lbf)
Bolt D, E : 24 N*m (245 kgf*cm, 18 ft.*lbf)

NOTICE:

Install the mounting bracket and water pump within 15 minutes of installing the oil pump assembly.


HINT:

Each bolt length is as follows.

A: 30 mm (1.181 in.)

B: 35 mm (1.378 in.)

C: 20 mm (0.787 in.)

E: 20 to 14 mm (0.787 to 0.551 in.) Double ended bolt



Hide 16100 20.INSTALL ENGINE WATER PUMP ASSEMBLY

A116192

a.

Install the engine water pump and a new gasket with the 3 bolts and 2 nuts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 12315A 21.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A080957

a.

Install the transverse engine engine mounting bracket with the 4 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 13407 22.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

a.

Align the pin hole in the crankshaft damper with the pin position and install the crankshaft damper sub-assembly.


b.

Provisionally install the bolt.


c.
A117461E01
0.54,0.388 0.827,0.57 0.287,0.182 10 SST 1.19,0.387 0.921,0.478 0.921,0.478 1.115,0.805 false

Using SST, tighten the bolt while holding the crankshaft damper.

SST
09213-14010  (91651-60865)
09330-00021  

Torque:
128 N*m (1305 kgf*cm, 95 ft.*lbf)

NOTICE:

Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump.



Hide 16173 23.INSTALL WATER PUMP PULLEY

A116191E06
1.542,2.063 1.99,1.958 true 2.042,1.875 2.333,2.052 0.292,0.177 10 false SST

a.

Using SST, install the water pump pulley with the 3 bolts.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

SST
09960-10010  (09962-01000, 09963-00700)


Hide 11101J 26.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

A064872

a.

Apply a light coat of engine oil to a new O-ring, and install it onto the camshaft timing oil control valve.


b.

Install the camshaft timing oil control valve with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Do not twist the O-ring.



Hide 23250 27.INSTALL FUEL INJECTOR ASSEMBLY

A115499E05
1.565,1.738 1.722,1.918 0.158,0.179 10 *1 1.761,1.795 2.23,1.466 false

a.

Apply a light coat of gasoline or spindle oil to a new O-ring, then install one onto each fuel injector.

Text in Illustration
*1 O-Ring


b.

Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.


c.
A260536

While turning the fuel injector left and right, install it onto the fuel delivery pipe.

Text in Illustration
V100135

Push
V100136

Turn

NOTICE:
·

Do not twist the O-ring.

·

After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.




Hide 23291 28.INSTALL INJECTOR VIBRATION INSULATOR

A115497

a.

Install 4 new injector vibration insulators onto the cylinder head.


Hide 23807V 29.INSTALL NO. 1 DELIVERY PIPE SPACER

A115501

a.

Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

NOTICE:

Install the delivery pipe No. 1 spacer in the correct direction.



Hide 23807 30.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

A115494

a.

Provisionally install the fuel delivery pipe with the 4 fuel injectors using the 3 bolts.

NOTICE:
·

Do not drop the fuel injectors when installing the fuel delivery pipe.

·

Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe.




b.
A115494E08
0.719,0.271 0.896,0.448 0.177,0.177 10 true A 1.448,0.771 1.635,0.958 0.188,0.188 10 true A 2.906,1.781 3.063,1.958 0.156,0.177 10 false B

Tighten the 3 bolts to the specified torque.

Torque:
Bolt A : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11201 31.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Install a new gasket onto the cylinder head cover.


b.
A260538

Apply seal packing to the cylinder head, as shown in the illustration.

Text in Illustration
V100155

Seal Packing

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.

·

Do not start engine for at least 2 hours after the installation.




c.

Provisionally install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.


d.
A370105E03
0.271,0.104 0.5,0.292 0.229,0.188 10 false 11 0.229,1 0.458,1.188 0.229,0.188 10 true 10 0.917,0.146 1.073,0.333 0.156,0.188 10 false 9 1.958,0.146 2.115,0.333 0.156,0.188 10 false 5 3.104,0.167 3.26,0.354 0.156,0.188 10 false 7 1.302,1.073 1.458,1.26 0.156,0.188 10 false 1 2.49,1.073 2.646,1.26 0.156,0.188 10 false 2 0.385,1.896 0.542,2.083 0.156,0.188 10 false 8 0.896,1.688 1.052,1.875 0.156,0.188 10 false 3 1.948,1.698 2.104,1.885 0.156,0.188 10 false 6 3.063,1.698 3.219,1.885 0.156,0.188 10 false 4

Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12204 32.INSTALL VENTILATION VALVE SUB-ASSEMBLY

A080963

a.

Install the ventilation valve onto the cylinder head cover.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 11452 33.INSTALL OIL LEVEL DIPSTICK GUIDE

a.

Apply engine oil to a new O-ring.


b.

Install the O-ring onto the oil level dipstick guide.


c.

Install the oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15100Q 34.INSTALL CRANKSHAFT POSITION SENSOR

a.

Apply a light coat of engine oil to the O-ring.

NOTICE:

If reusing the camshaft position sensor, be sure to inspect the O-ring.



b.

Install the crankshaft position sensor with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 12108A 35.INSTALL OIL FILLER CAP GASKET

a.

Install the oil filler cap gasket onto the oil filler cap.


Hide 12108 36.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap onto the cylinder head cover.


Hide 16331A 37.INSTALL THERMOSTAT

a.

Install a new gasket onto the thermostat.


b.
A116188E07
1.688,0.99 2.5,0.813 true 1.271,0.271 1.583,0.448 0.313,0.177 10 true 10° 1.875,0.271 2.188,0.448 0.313,0.177 10 true 10° 2.521,0.719 2.76,0.906 0.24,0.188 10 false *1

Install the thermostat with the jiggle valve facing upward.

Text in Illustration
*1 Jiggle Valve

HINT:

The jiggle valve may be set within 10° on either side as shown in the illustration.



Hide 16321 38.INSTALL WATER INLET

A080960

a.

Install the water inlet with radiator hose using the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 89422 39.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

a.

Install a new gasket onto the engine coolant temperature sensor.


b.
A117464

Using a 19 mm socket wrench, install the engine coolant temperature sensor.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 83530 40.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

A370106E04
1.948,0.698 1.344,0.438 false 1.125,0.313 1.438,0.51 0.313,0.198 10 false *1

a.

Apply adhesive to the end 2 or 3 threads of the oil pressure switch.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Do not start the engine for at least 1 hour after the installation.



b.
A117463

Using a 24 mm deep socket wrench, install the oil pressure switch.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 89615 41.INSTALL KNOCK SENSOR

A370107E02
1.49,1.719 1.948,1.938 0.458,0.219 10 true +- 30°

a.

Install the knock sensor with the nut as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 19100P 42.INSTALL SPARK PLUG

A080968

a.

Using a 16 mm spark plug wrench, install the 4 spark plugs.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)