Home › Engine / Hybrid System › 2NZ-FE FUEL › FUEL SYSTEM
RM19S0E _51 Engine / Hybrid System _051452 2NZ-FE FUEL _0248092 FUEL SYSTEM L

2NZ-FE FUEL  FUEL SYSTEM  PRECAUTION  


PRECAUTIONS


a.

Before working on the fuel system, disconnect the cable from the negative battery terminal.

NOTICE:

after turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice proceeding with work. (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)



b.

Do not work on the fuel system near any open flames. Never smoke when working on this system.


c.

Keep rubber and leather parts away from gasoline.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Perform this procedure when the engine coolant temperature is below 60°C (140°F).

·

Perform the following procedure to prevent fuel from spilling out before removing any fuel system parts.

·

Even after discharging the fuel pressure, when disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

for 60/40 Split Seat Type LH Side:



b.

for 60/40 Split Seat Type RH Side:



c.

for Fold Down Seat Type:



d.
A247490E03
0.333,0.708 0.625,0.635 false 0.344,1.083 0.938,0.958 false 0.979,1.438 1.521,1.26 false 0.146,0.646 0.323,0.833 0.177,0.188 10 false *1 0.146,1.01 0.323,1.198 0.177,0.188 10 false *2 0.771,1.365 0.948,1.552 0.177,0.188 10 false *3

Remove the rear floor service hole cover.

Text in Illustration
*1 Clip remover
*2 Protective tape
*3 Butyl tape


e.
A247491

Disconnect the connector from the fuel pump assembly.


f.

Start the engine.


g.

After the engine stops naturally, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop naturally.


HINT:

DTC P0171/25 may be set.



h.

Crank the engine again and make sure that the engine does not start.


i.

Remove the fuel tank cap and discharge the pressure from the fuel tank.


j.

Disconnect the cable from the negative battery terminal.


k.

Connect the connector of the fuel pump assembly.



FUEL SYSTEM


a.

When disconnecting the high-pressure fuel line, a large amount of gasoline will splash out. Take the following precautions.

i.

Discharge the fuel system pressure.


ii.

Remove the fuel tube clip.


iii.

Disconnect the fuel tube.


iv.

Drain the fuel remaining inside the fuel pump tube into a container.


v.
B000679E28
1.771,1.271 1.063,1.271 false 0.844,1.177 1.01,1.344 0.167,0.167 10 false *1

Protect the contact surface by covering it with a plastic bag.

Text in Illustration
*1 Plastic Bag

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



vi.

Put a container under the connection part.



b.

Observe the following precautions when disconnecting the fuel tube connector (Quick Type A).

i.
A125132E03
2.083,0.927 2.604,0.604 false 2.615,0.49 2.771,0.646 0.156,0.156 10 true *1

Remove the EFI fuel pipe clamp.

Text in Illustration
*1 EFI fuel pipe clamp


ii.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


iii.
A254817E06
2.677,1.198 2.958,1.083 2.958,1.083 2.719,1.458 false 2.5,2.302 2.594,2.552 false 1.125,2.313 1.229,2.583 false 1.688,2.906 1.583,3.25 false 2.583,3.104 2.542,3.25 false 2.021,2.938 2.115,3.198 2.115,3.198 2.188,2.938 false 1,2.115 1.188,2.271 0.188,0.156 10 false *2 2.948,0.969 3.135,1.177 0.188,0.208 10 false *1 2.385,2.115 2.573,2.26 0.188,0.146 10 false *1 1.448,3.219 1.635,3.375 0.188,0.156 10 false *3 2.042,3.229 2.229,3.385 0.188,0.156 10 false *4 2.406,3.219 2.594,3.375 0.188,0.156 10 false *5

Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.

Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Fuel Tube Connector
V100135

Pinch
V100136

Pull Out

NOTICE:

Do not use any tools.



iv.
A193370

If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.

Text in Illustration
V100135

Pull
V100136

Push

NOTICE:

Do not use any tools.



v.

Check the sealing surfaces of the disconnected parts, and clean them if necessary.


vi.
A158902E02
1.1,1.677 1.27,1.847 0.17,0.17 10 *1 1.22,1.631 1.727,1.276 false

Protect the contact surface by covering it with a plastic bag.

Text in Illustration
*1 Plastic Bag

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.




c.
A254813

Observe the following precautions when connecting the fuel tube connectors (Quick Type A).

Text in Illustration
V100135

Push

i.

Check that there are no scratches or foreign objects on the connecting part.


ii.

Line up the pipe and connector and push them together until a "click" sound is heard.

HINT:

If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.



iii.
A088340

After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.

Text in Illustration
V100136

Pull


iv.
A200114E02
0.99,0.552 1.406,0.854 false 0.813,0.469 0.979,0.719 0.167,0.25 10 true *1

Install the EFI fuel pipe clamp.

Text in Illustration
*1 EFI fuel pipe clamp
V100135

Push


v.

Inspect for fuel leaks.



d.
A223364

Observe the following procedure when disconnecting the fuel tube connectors (Quick Type B).

Text in Illustration
V100135

Pull

i.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


ii.

Disengage the fuel tube connector cover.

NOTICE:

Do not use any tools.



iii.
A254817E06
2.677,1.198 2.958,1.083 2.958,1.083 2.719,1.458 false 2.5,2.302 2.594,2.552 false 1.125,2.313 1.229,2.583 false 1.688,2.906 1.583,3.25 false 2.583,3.104 2.542,3.25 false 2.021,2.938 2.115,3.198 2.115,3.198 2.188,2.938 false 1,2.115 1.188,2.271 0.188,0.156 10 false *2 2.948,0.969 3.135,1.177 0.188,0.208 10 false *1 2.385,2.115 2.573,2.26 0.188,0.146 10 false *1 1.448,3.219 1.635,3.375 0.188,0.156 10 false *3 2.042,3.229 2.229,3.385 0.188,0.156 10 false *4 2.406,3.219 2.594,3.375 0.188,0.156 10 false *5

Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.

Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Fuel Tube Connector
V100135

Pinch
V100136

Pull Out

NOTICE:

Do not use any tools.



iv.
A193370

If the connector and pipe are stuck, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.

Text in Illustration
V100135

Pull
V100136

Push

NOTICE:

Do not use any tools.



v.

Check the sealing surfaces of the disconnected parts, and clean them if necessary.


vi.
A158902E02
1.1,1.677 1.27,1.847 0.17,0.17 10 *1 1.22,1.631 1.727,1.276 false

Protect the contact surface by covering it with a plastic bag.

Text in Illustration
*1 Plastic Bag

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.




e.
A254813

Observe the following precautions when connecting the fuel tube connectors (Quick Type B).

Text in Illustration
V100135

Push

i.

Check that there are no scratches or foreign objects on the connecting part.


ii.

Line up the pipe and connector and push them together until a "click" sound is heard.

HINT:

If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.



iii.
A088340

After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.

Text in Illustration
V100136

Pull


iv.
A254814

Engage the fuel tube connector cover.

Text in Illustration
V100135

Push


v.

Inspect for fuel leaks.



f.
A254815E01
0.583,1.77 0.742,1.911 0.160,0.141 10 *1 1.469,1.77 1.628,1.911 0.160,0.141 10 *2 0.717,1.946 0.901,2.482 false 2.096,1.77 2.255,1.911 0.160,0.141 10 *3 2.752,2.08 2.912,2.221 0.160,0.141 10 *4 1.637,3.164 1.797,3.305 0.160,0.141 10 *5 2.23,1.946 2.368,2.348 false 1.902,2.823 1.595,1.946 1.595,1.946 1.922,2.508 false 2.724,2.565 2.839,2.253 false 1.753,2.941 1.753,3.162 false

Observe the following procedure when disconnecting the fuel tube connectors (Quick Type C).

i.

Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.


ii.

Pull back the retainer of the fuel tube connector as shown in the illustration, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.

NOTICE:

Do not use any tools.


Text in Illustration
*1 Rubber Hose
*2 O-Ring
*3 Retainer
*4 Fuel Pipe
*5 Fuel Tube Connector
V100135

Pull Back
V100136

Pull Out


iii.
A254816

If the connector and pipe are stuck, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.

Text in Illustration
V100135

Push
V100136

Pull

NOTICE:

Do not use any tools.



iv.

Check the sealing surfaces of the disconnected parts, and clean them if necessary.


v.
A247587E01
2.738,0.148 2.887,0.301 0.149,0.152 10 *1 2.481,0.613 2.806,0.316 false

Protect the contact surface by covering it with a plastic bag.

Text in Illustration
*1 Plastic Bag

NOTICE:

Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.




g.
A247589

Observe the following procedure when connecting the fuel tube connector (Quick Type C).

Text in Illustration
V100135

Push

i.

Check that there are no scratches or foreign objects on the connecting part.


ii.

Line up the pipe and connector and push them together until a "click" sound is heard.

If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.


iii.
A247590

After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.

Text in Illustration
V100135

Pull


iv.

Inspect for fuel leaks.




INJECTOR


a.
A106965

Observe the following precautions when removing and installing the fuel injector.

i.

Do not reuse the O-ring and insulator.


ii.

When placing a new O-ring onto the injector, do not damage the O-ring.


iii.

Coat the new O-ring with gasoline or spindle oil before installing it. Do not use engine, gear or brake oil.



b.
A106966E03
2.223,0.562 2.372,0.707 0.149,0.145 10 *2 1.829,0.639 2.2,0.639 false 2.223,1.818 2.372,1.963 0.149,0.145 10 *3 1.865,1.896 2.2,1.896 false 2.223,0.335 2.372,0.480 0.149,0.145 10 *1 1.919,0.412 2.2,0.412 false

Install the injector into the delivery pipe and cylinder head, as shown in the illustration. Apply gasoline or spindle oil to the contact surfaces of the delivery pipe and the injector before installing the injector.

Text in Illustration
*1 Delivery pipe
*2 O-ring
*3 Insulator



INSPECT FOR FUEL LEAK


a.

Check that there is no fuel leakage after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).