1. PRECAUTION
When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
| *1 | Cord |
Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.
77020A
2.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
3.DRAIN FUEL
58153
4.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR
Remove the 2 nuts and the front No. 2 floor heat insulator.
77606F
5.REMOVE FUEL TANK COVER VENT CASE SUB-ASSEMBLY
Remove the clip.
Remove the bolt and fuel tank cover vent case sub-assembly.
77209D
6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Before disconnecting the fuel tube connector, check for dirt or other foreign matter on the fuel tube connector and the pipe, and clean them if necessary.
Disengage the fuel tube connector cover.
| *1 | Checker |
| *2 | Fuel Tube Connector |
| *3 | O-ring |
| *4 | Retainer |
|
Pinch |
|
Pull |
Pinch the retainer by hand from both sides, and pull out the fuel tube connector from the pipe.
If the fuel tube connector and pipe are stuck together, push in and pull out the fuel tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tube connector.
Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.
The fuel tube connector and pipe are sealed by O-rings, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
Do not use any tools.
After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the pipe.
After disconnecting the fuel tube, protect the contact surfaces by covering them with a plastic bag.
Do not bend or twist the tubes.
77262
7.DISCONNECT NO. 2 FUEL EMISSION TUBE
Before disconnecting the fuel tube connector, check for dirt or other foreign matter on the fuel tube connector and the pipe, and clean them if necessary.
Loosen the clamp and disconnect the No. 2 fuel emission tube.
| *1 | Rubber Hose |
| *2 | O-ring |
| *3 | Fuel Pipe |
| *4 | Retainer |
| *a | Pull Back |
| *b | Pull Out |
If the fuel tube connector and pipe are stuck together, push in and pull out the fuel tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tube connector.
Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.
The fuel tube connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
Do not use any tools.
After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the pipe.
After disconnecting the fuel tube, protect the contact surfaces by covering them with a plastic bag.
Do not bend or twist the tubes.
77100
8.REMOVE FUEL TANK ASSEMBLY
Remove the bolt.
Disengage the clip as shown in the illustration and remove the fuel tank filler pipe flange plate.
Using an engine lifter, support the fuel tank assembly.
Separate the 2 fuel hoses shown in the illustration.
Remove the 4 bolts and fuel tank assembly.
Make sure that the fuel tank does not fall.
77209D
9.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disengage the clamp and remove the fuel tank main tube from the fuel tank assembly.
77262
10.REMOVE NO. 2 FUEL EMISSION TUBE
Disengage the clamp and remove the No. 2 fuel emission tube from the fuel tank assembly.
77701W
11.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY
Remove the No. 1 canister outlet hose from the fuel tank assembly.
23841H
12.REMOVE FUEL HOSE CLAMP
Remove the fuel hose clamp.
77217C
13.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT
Disengage the clamp as shown in the illustration, and remove the No. 2 fuel tank filler pipe support.
77216A
14.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT
Disengage the clamp as shown in the illustration, and remove the No. 1 fuel tank filler pipe support.
77218A
15.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT
Disengage the clamp as shown in the illustration, and remove the No. 3 fuel tank filler pipe support.