Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL INJECTOR › 2011.08–2015.06
RM19S0E _51 Engine / Hybrid System _051453 1NZ-FE FUEL _0248097 FUEL INJECTOR G

1NZ-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.
A154756E05
2.843,0.208 2.993,0.348 0.150,0.141 10 *1 0.042,0.02 0.193,0.158 0.151,0.137 10 *a

Check the resistance.

Text in Illustration
*1 Ohmmeter
*a Component without harness connected
(Fuel Injector Assembly)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the injector assembly.



b.

Check the operation.

CAUTION:

Perform the inspection in a well-ventilated area.

Do not perform the inspection near any open flames.


i.
A147389E09
2.021,1.271 2.229,1.521 false 0.875,1.156 1.094,0.729 false 0.406,1.427 0.635,0.958 false 2.448,0.781 2.594,0.427 false 2.51,0.24 2.677,0.417 0.167,0.177 10 false *1 0.583,0.792 0.771,0.969 0.188,0.177 10 false *4 2.198,1.542 2.396,1.729 0.198,0.188 10 false *3 1.063,0.552 1.24,0.729 0.177,0.177 10 false *2

Connect SST (fuel tube connector) to SST (hose), and then connect them to the fuel pipe (vehicle side).

SST
09268-31013  (90467-13001, 95336-08070, 09268-41500)

Text in Illustration
*1 Fuel Pipe
*2 SST (Clip)
*3 SST (Fuel Tube Connector)
*4 SST (Hose)


ii.
A129474E17
0.125,0.548 0.310,0.702 0.185,0.155 10 *1 0.125,1.118 0.310,1.273 0.185,0.155 10 *2 0.125,0.049 0.310,0.204 0.185,0.155 10 *3 2.479,0.034 2.664,0.189 0.185,0.155 10 *4 2.72,1.098 2.905,1.252 0.185,0.155 10 *5 2.72,1.656 2.905,1.811 0.185,0.155 10 *6 0.85,0.632 0.327,0.632 false 0.875,0.394 0.333,0.151 false 1.929,0.598 2.488,0.158 false 0.909,1.207 0.327,1.207 false 2.695,1.741 1.918,1.741 false 2.694,1.181 2.282,1.181 false

Install the new O-ring onto the fuel injector.

SST
09268-31013  (90467-13001, 95336-08070, 09268-41300, 09268-41110)

Text in Illustration
*1 SST (Clip)
*2 SST (Adapter)
*3 SST (Hose)
*4 O-Ring
*5 SST (Clamp)
*6 Vinyl Tube


iii.

Connect SST (adapter and hose) to the injector, and hold the injector and union with SST (clamp).


iv.

Put the injector into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube onto the injector assembly to prevent gasoline splashes.




vi.
A075915E37
2.208,0.594 2.01,1.083 2.01,1.083 2.01,1.156 false 1.948,1.156 2.104,1.354 0.156,0.198 10 false *1

Connect SST (wire) to the injector assembly and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Injection Volume:
Tester Connection Condition Specified Condition
Positive terminal - Ground terminal Per 15 seconds 47 to 58 cm3 (2.9 to 3.5 cu in.)


Text in Illustration
*1 SST (Wire)
V100135

Connect

Difference between each injector:

11 cm3 (0.7 cu in.) or less


CAUTION:

Always do the switching at the battery side.


If the injection volume is not as specified, replace the injector assembly.



c.
A198105

Check for leaks.

i.

In the condition above, disconnect the test probes of SST (wire) from the battery and check if the fuel leaks from the injector.

Fuel Drop:

1 drop or less every 12 minutes