Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL TANK
RM19S0E _51 Engine / Hybrid System _051453 1NZ-FE FUEL _0248099 FUEL TANK A

1NZ-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77218A 1.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.
A247530E01
0.237,0.352 0.397,0.498 0.160,0.146 10 *a 1.851,0.352 2.011,0.498 0.160,0.146 10 *b

Install the fuel tank filler pipe support No. 3 in the position shown in the illustration.

Text in Illustration
*a Installation Position
*b Cutaway View
V100136

Front of Vehicle


Hide 77216A 2.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A260850

Install the No. 1 fuel tank filler pipe support in the position shown in the illustration.

Text in Illustration
V100136

Out Side of Vehicle


Hide 77217C 3.INSTALL NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A260851E01
0.416,2.621 0.576,2.772 0.160,0.150 10 *a 1.876,2.621 2.036,2.772 0.160,0.150 10 *b

Install the No. 2 fuel tank filler pipe support in the position shown in the illustration.

Text in Illustration
*a Clamp Position
*b Section
V100136

Out Side of Vehicle


Hide 23841H 4.INSTALL FUEL HOSE CLAMP

a.

Install the fuel hose clamp onto the fuel tank assembly.


Hide 77701W 5.INSTALL NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Install the No. 1 canister outlet hose sub-assembly to the fuel tank assembly.


Hide 77262 6.INSTALL NO. 2 FUEL EMISSION TUBE

a.

Install the No. 2 fuel emission tube into the groove of the fuel tank assembly.


Hide 77209F 7.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Install the fuel tank main tube into the groove of the fuel tank assembly.


Hide 77100 8.INSTALL FUEL TANK ASSEMBLY

a.

Clean and degrease the bolt holes.


b.

Using an engine lifter, set the fuel tank assembly in the installation position.


c.

Install the fuel tank assembly with 4 new bolts.

Torque:
14 N*m (146 kgf*cm, 11 ft.*lbf)


d.
A247509

Assemble the 2 fuel hoses to the position shown in the illustration.


e.
A247507

Install the fuel tank filler pipe flange plate as shown in the illustration.


f.

Install the bolt.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


g.

Install the fuel tube.


Hide 77262 9.CONNECT NO. 2 FUEL EMISSION TUBE

a.

Align the axis of the fuel tube connector and the axis of the pipe, and push in the fuel tube connector until the retainer makes a click sound.

NOTICE:
·

Check that there are no scratches or foreign objects on the connecting part.

·

Check that the No. 2 fuel emission tube is inserted securely.




b.

After connecting the fuel tube connector, pull on the fuel tube connector and the pipe to make sure they are firmly connected.


Hide 77209F 10.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Align the axis of the fuel tube connector and the axis of the pipe, and push in the fuel tube connector until the retainer makes a click sound.

NOTICE:
·

Check that there are no scratches or foreign objects on the connecting part.

·

Check that the fuel tank main tube is inserted securely.

·

After installing the checker, check that the fuel tank main tube is securely connected by pulling on it.




b.

After connecting the fuel tube connector, pull on the fuel tube connector and the pipe to make sure they are firmly connected.


c.

Push the fuel tube connector cover in to lock it.


Hide 77606F 11.INSTALL FUEL TANK COVER VENT CASE SUB-ASSEMBLY

a.

Install the fuel tank cover vent case with the bolt and the clip.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 58153 12.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR

a.

Install the front No. 2 floor heat insulator with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 13.ADD FUEL

Hide 77020A 14.INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE