Home › Engine / Hybrid System › 1NZ-FE COOLING › COOLANT
RM19S0E _51 Engine / Hybrid System _051458 1NZ-FE COOLING _0248121 COOLANT A

1NZ-FE COOLING  COOLANT  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:

Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans may automatically start to run if the coolant temperature is high and/or the air conditioning is on.


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT (w/ Engine Drain Cock Plug)

NOTICE:

To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.


a.
A302919E02
1.688,0.927 2.792,0.427 false 1.052,2.5 0.51,3.01 true 0.604,0.5 1.438,1.01 true 2.823,0.313 3.052,0.531 0.229,0.219 10 false *1 0.406,0.385 0.635,0.604 0.229,0.219 10 false *3 0.333,2.979 0.563,3.198 0.229,0.219 10 false *2

Install a hose with an inside diameter of 9 mm (0.3543 in.) to the radiator drain cock.

Text in Illustration
*1 Water Filler Cap Sub-assembly
*2 Radiator Drain Cock Plug
*3 Cylinder Block Drain Cock Plug


b.

Loosen the radiator drain cock plug.


c.

Remove the water filler cap sub-assembly.


d.

Loosen the cylinder block drain cock plug, then drain the engine coolant.


Hide 2.DRAIN ENGINE COOLANT (w/o Engine Drain Cock Plug)

NOTICE:

To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.


a.
A304787E02
1.688,0.927 2.656,0.396 true 0.594,2.865 1.042,2.49 true 2.698,0.26 2.938,0.49 0.24,0.229 10 false *1 0.417,2.823 0.656,3.052 0.24,0.229 10 false *2

Install a hose with an inside diameter of 9 mm (0.3543 in.) to the radiator drain cock.

Text in Illustration
*1 Water Filler Cap Sub-assembly
*2 Radiator Drain Cock Plug


b.

Loosen the radiator drain cock plug.


c.

Remove the water filler cap sub-assembly, then drain the engine coolant.


Hide 3.ADD ENGINE COOLANT (w/ Engine Drain Cock Plug)

a.

Tighten the cylinder block drain cock plug.

Torque:
13 N*m (133 kgf*cm, 9.6 ft.*lbf)


b.

Tighten the radiator drain cock plug by hand.


c.

Remove the hose from the radiator drain cock.


d.
A206788E09
2.729,0.865 2.844,0.604 false 2.229,1.583 2.427,1.792 false 2.865,0.51 3.021,0.656 0.156,0.146 10 false *a 2.74,1.115 2.969,1.281 0.229,0.167 10 true *c 2.458,1.708 2.625,1.854 0.167,0.146 10 false *b

Slowly fill the radiator assembly with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Engine coolant level should be within 20 mm (0.787 in.) from the filler tube end.)

Text in Illustration
*a Filler Tube End
*b Coolant Level
*c 20 mm (0.787 in.)

Capacity:
Transaxle Type Coolant Capacity
Automatic Transaxle 4.6 liters (4.9 US qts, 4.0 Imp. qts)
Manual Transaxle 4.7 liters (5.0 US qts, 4.1 Imp. qts)


NOTICE:

Do not substitute water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate engine coolant with long-life hybrid organic acid technology (engine coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



e.

Remove the reserve tank cap.


f.
A246002E06
2.135,1 2.635,0.906 false 2.208,1.667 2.677,1.771 false 2.708,0.781 2.948,0.99 0.24,0.208 10 false *a 2.719,1.708 2.958,1.917 0.24,0.208 10 false *b

Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.

Text in Illustration
*a Full Line
*b Low Line


g.

Install the water filler cap sub-assembly securely.


h.

Install the reserve tank cap.


i.

Bleed air from the cooling system.

i.

Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

NOTICE:
·

Make sure that the radiator reserve tank assembly still has some engine coolant in it.

·

If the engine coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.

·

If the radiator reserve tank assembly does not have enough engine coolant, perform the following: stop the engine, wait until the engine coolant has cooled down and add engine coolant until the radiator reserve tank assembly is filled to the full line.



HINT:

The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.




j.

Stop the engine and wait until the engine coolant cools down.


k.

Recheck the engine coolant level inside the radiator reserve tank assembly. If it is below the full level, add engine coolant.


Hide 4.ADD ENGINE COOLANT (w/o Engine Drain Cock Plug)

a.

Tighten the radiator drain cock plug by hand.


b.

Remove the hose from the radiator drain cock.


c.
A206788E09
2.729,0.865 2.844,0.604 false 2.229,1.583 2.427,1.792 false 2.865,0.51 3.021,0.656 0.156,0.146 10 false *a 2.74,1.115 2.969,1.281 0.229,0.167 10 true *c 2.458,1.708 2.625,1.854 0.167,0.146 10 false *b

Slowly fill the radiator assembly with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Engine coolant level should be within 20 mm (0.787 in.) from the filler tube end.)

Text in Illustration
*a Filler Tube End
*b Coolant Level
*c 20 mm (0.787 in.)

Capacity:
Transaxle Type Coolant Capacity
Automatic Transaxle 4.6 liters (4.9 US qts, 4.0 Imp. qts)
Manual Transaxle 4.7 liters (5.0 US qts, 4.1 Imp. qts)


NOTICE:

Do not substitute water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate engine coolant with long-life hybrid organic acid technology (engine coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



d.

Remove the reserve tank cap.


e.
A246002E06
2.135,1 2.635,0.906 false 2.208,1.667 2.677,1.771 false 2.708,0.781 2.948,0.99 0.24,0.208 10 false *a 2.719,1.708 2.958,1.917 0.24,0.208 10 false *b

Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.

Text in Illustration
*a Full Line
*b Low Line


f.

Install the water filler cap sub-assembly securely.


g.

Install the reserve tank cap.


h.

Bleed air from the cooling system.

i.

Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

NOTICE:
·

Make sure that the radiator reserve tank assembly still has some engine coolant in it.

·

If the engine coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.

·

If the radiator reserve tank assembly does not have enough engine coolant, perform the following: stop the engine, wait until the engine coolant has cooled down and add engine coolant until the radiator reserve tank assembly is filled to the full line.



HINT:

The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.




i.

Stop the engine and wait until the engine coolant cools down.


j.

Recheck the engine coolant level inside the radiator reserve tank assembly. If it is below the full level, add engine coolant.