Home › Engine / Hybrid System › 1NZ-FE STARTING › STARTER
RM19S0E _51 Engine / Hybrid System _051462 1NZ-FE STARTING _0248146 STARTER G

1NZ-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

NOTICE:

The following tests must be performed within 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A249985E01
2.58,1.814 2.58,2.273 false 2.505,2.301 2.762,2.492 0.257,0.192 10 *1 1.344,0.344 1.601,0.535 0.257,0.192 10 *2 1.554,0.428 1.716,0.428 1.716,0.428 2.004,0.707 false

Connect the battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear is extended.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.

Text in Illustration
*1 Terminal 50
*2 Body



b.
A249986E03
2.583,1.885 2.583,2.344 false 1.552,0.479 1.719,0.479 1.719,0.479 2,0.76 false 2.5,2.375 2.76,2.563 0.26,0.188 10 false *1 1.344,0.396 1.604,0.583 0.26,0.188 10 false *2

Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

Text in Illustration
*1 Terminal 50
*2 Body



c.

Perform a no-load performance test.

i.

Clamp the starter in a vise.

NOTICE:

Do not clamp the vise too tightly.



ii.
A249987E02
2.667,1.854 2.667,2.406 false 2.594,1.615 2.042,2.156 false 1.927,0.792 1.625,0.5 false 2.583,2.427 2.76,2.594 0.177,0.167 10 false *1 1.844,2.094 2.021,2.26 0.177,0.167 10 false *2 1.417,0.375 1.594,0.542 0.177,0.167 10 false *3

Connect the battery and an ammeter to the starter as shown in the illustration.

Text in Illustration
*1 Terminal 50
*2 Terminal 30
*3 Body


iii.

Check that the starter rotates smoothly and steadily with the clutch pinion gear extended.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for an open circuit.

i.
A247248E01
2.026,1.217 1.448,1.794 false 1.241,1.712 1.411,1.865 0.170,0.152 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.

Text in Illustration
*1 Segment



b.

Check the commutator for a short to ground.

i.
A247247E01
1.506,1.535 1.676,1.685 0.170,0.149 10 *1 0.581,1.258 0.751,1.408 0.170,0.149 10 *2 2.17,1.145 1.702,1.614 false 1.245,0.868 0.776,1.337 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil Core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.

Text in Illustration
*1 Segment
*2 Coil Core



c.

Check the commutator surface for dirt and burns.

If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.


d.

Check the commutator for circle runout.

i.
A247250

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A247251

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

25.0 mm (0.9843 in.)


Minimum diameter:

24.0 mm (0.9449 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A247252

Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.0079 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A248655

Using a vernier caliper, measure the brush length.

Standard length:

11.6 mm (0.4567 in.)


Minimum length:

7.6 mm (0.2992 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


Hide 28011 4.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A247253E01
1.838,1.858 2.004,2.017 0.166,0.159 10 *a 1.779,2.88 1.945,3.040 0.166,0.159 10 *b

Hold the starter clutch sub-assembly, rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If necessary, replace the starter clutch sub-assembly.

Text in Illustration
*a Free
*b Lock


Hide 28150 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A247243E01
2.519,0.601 2.519,0.208 2.519,0.208 2.355,0.208 false 2.148,0.13 2.303,0.294 0.155,0.164 10 *1

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the magnet starter switch assembly.

Text in Illustration
*1 Plunger



b.

Check the holding coil for an open circuit.

i.
A247245E04
2.542,0.958 2.906,1.396 false 1.25,0.76 0.927,0.396 false 2.969,1.313 3.125,1.479 0.156,0.167 10 false *1 0.719,0.302 0.875,0.469 0.156,0.167 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.

Text in Illustration
*1 Terminal 50
*2 Body