Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248166 AUTOMATIC TRANSAXLE UNIT G

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35667A 1.INSPECT DIRECT CLUTCH DISC

a.
C067852

Check whether the sliding surface of the direct clutch disc, rear clutch flange and direct clutch flange are worn or burnt.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.



If necessary, replace them.


Hide 35683 2.INSPECT 1ST AND REVERSE BRAKE DISC

D025046

a.

Check to see if the sliding surface of the 1st and reverse brake disc, 1st and reverse brake plate and 1st and reverse brake flange are worn or burnt.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak in Toyota Genuine ATF WS for at least 15 minutes.



If necessary, replace them.


Hide 35682 3.INSPECT 2ND BRAKE BRAKE DISC

C067852

a.

Check whether the sliding surfaces of the 2nd brake brake disc, No. 1 2nd brake brake flange and 2nd brake brake flange are worn or burnt.

NOTICE:
·

If the lining of the disc is peeling off or discolored or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.



If necessary, replace them.


Hide 34633 4.INSPECT 2ND COAST AND OVERDRIVE BRAKE DISC

C067852

a.

Check whether the sliding surfaces of the 2nd coast and overdrive brake disc, No. 2 2nd coast and overdrive brake flange and 2nd coast and overdrive brake flange are worn or burnt.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.



If necessary, replace them.


Hide 35633 5.INSPECT FRONT CLUTCH CLUTCH DISC

a.
C067852

Check whether the sliding surface of the front clutch clutch disc, No. 1 clutch plate and forward clutch flange are worn or burnt.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.



If necessary, replace them.


Hide 35677H 6.INSPECT REVERSE CLUTCH DISC

a.
C067852

Check whether the sliding surfaces of the reverse clutch disc, No. 3 clutch plate and reverse clutch flange are worn or burnt.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.



If necessary, replace them.


Hide 35604 7.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C067872

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

32.9 mm (1.2953 in.)


If the free length is shorter than the standard free length, replace the direct clutch return spring sub-assembly.


Hide 35068 8.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C059838

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

13.96 mm (0.5496 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 35608L 9.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C067865

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

14.65 mm (0.5768 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 34603B 10.INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C059838

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.88 mm (0.7039 in.)


If the free length is shorter than the standard free length, replace the overdrive brake return spring sub-assembly.


Hide 35603A 11.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C067855

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.69 mm (0.8540 in.)


If the free length is shorter than the standard free length, replace the forward clutch return spring sub-assembly.


Hide 35606A 12.INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C068212

Shake the direct clutch pin and confirm that the check ball is not stuck.


b.

Apply low pressure compressed air to the check ball and check that no air leakage is identified.

If necessary, replace the direct clutch piston sub-assembly.


Hide 35708G 13.INSPECT INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C068213

Shake the direct clutch pin and confirm that the check ball is not stuck.


b.

Apply low pressure compressed air to the check ball and check that no air leakage is identified.

If necessary, replace the intermediate shaft sub-assembly.