Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248166 AUTOMATIC TRANSAXLE UNIT A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572A 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C117101

Remove the nut, washer and the transmission control shaft lever.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C117104

Using a screwdriver, pry out the lock plate and remove the nut, lock plate and washer.


b.
C117106

Remove the 2 bolts and pull out the park/neutral position switch assembly.


Hide 89413B 3.REMOVE TRANSMISSION REVOLUTION SENSOR

U134429

a.

Remove the bolt and the transmission revolution sensor.


b.

Remove the O-ring from the transmission revolution sensor.


Hide 32921C 4.REMOVE OIL COOLER TUBE UNION

U134877

a.

Remove the 2 oil cooler tube unions from the transaxle case.


b.

Remove the 2 O-rings from the 2 oil cooler tube unions.


Hide 35104Q 5.REMOVE NO. 1 TRANSAXLE CASE PLUG

C067754

a.

Remove the 4 No. 1 transaxle case plugs from the transaxle housing and the transaxle case.


b.
C067755

Remove the No. 1 transaxle case plug from the transaxle case.


c.

Remove the 5 O-rings from each No. 1 transaxle case plugs.


Hide 35012 6.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

C067752

a.

Remove the transmission breather hose sub-assembly from the breather plug.


Hide 35104E 7.REMOVE BREATHER PLUG

a.

Remove the breather plug from the transaxle case.


b.

Remove the O-ring from the breather plug.


Hide 30500 8.FIX AUTOMATIC TRANSAXLE ASSEMBLY

a.
C163764E02
1.52,1.974 1.676,2.130 0.156,0.156 10 *1 1.298,1.83 1.637,1.957 1.637,1.957 1.974,1.829 false

Secure the transaxle on wooden blocks.

Text in Illustration
*1 Wooden Block


Hide 35106D 9.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.

Remove the drain plug and gasket from the automatic transaxle oil pan sub-assembly.


b.
U134425

Remove the 19 bolts, automatic transaxle oil pan sub-assembly and the automatic transaxle oil pan gasket.


c.
U134466

Remove the 2 oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


d.

Examine the particles in the automatic transaxle oil pan gasket.

i.

Collect any steel chips with the removed magnets.

Carefully look at the foreign matter and particles in the automatic transaxle oil pan gasket and on the magnets to predict the type of wear which might be found in the transaxle.

Steel (magnetic): bearing, gear and clutch plate wear

Brass (non-magnetic): bearing wear



Hide 35330 10.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C062685

a.

Remove the 3 bolts and the valve body oil strainer assembly.


b.
U134876

Remove the oil strainer gasket from the valve body oil strainer assembly.


Hide 35410 11.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C355249

Disconnect the 5 connectors from the transmission valve body assembly.


b.

Remove the bolt and the lock plate, and separate the transmission wire.


c.
U134464E04
2.25,0.604 2.646,0.458 false 2.25,1.177 2.615,1.177 false 2.677,0.375 2.896,0.573 0.219,0.198 10 false *1 2.635,0.99 2.865,1.156 0.229,0.167 10 false *2

Remove the 2 bolts, manual detent spring cover and the manual detent spring.

Text in Illustration
*1 Manual Detent Spring
*2 Manual Detent Spring Cover


d.
C355250

Remove the 13 bolts and the transmission valve body assembly from the transaxle case.


Hide 82125J 12.REMOVE TRANSMISSION WIRE

C062929

a.

Remove the bolt and the transmission wire from the transaxle case.


b.
C067760

Remove the O-ring from the transmission wire.


Hide 35149B 13.REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

C067757

a.

Remove the transaxle case 2nd brake gasket from the transaxle case.


Hide 35145C 14.REMOVE TRANSAXLE CASE GASKET

C067758

a.

Remove the transaxle case gasket from the transaxle case.


Hide 35159 15.REMOVE BRAKE DRUM GASKET

U134430

a.

Remove the brake drum gasket from the transaxle case.


Hide 35251 16.REMOVE CHECK BALL BODY

C067767

a.

Remove the check ball body and the check ball body compression spring from the transaxle case.


Hide 35423 17.REMOVE B-2 ACCUMULATOR PISTON

C067761

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-2 accumulator piston and the B-2 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
D025038

Remove the 2 B-2 accumulator piston O-rings from the B-2 accumulator piston.


Hide 35426D 18.REMOVE C-3 ACCUMULATOR PISTON

C067762

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston and the C-3 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
D025039

Remove the 2 C-3 accumulator piston O-rings from the C-3 accumulator piston.


Hide 35425A 19.REMOVE C-2 ACCUMULATOR PISTON

C067763

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the C-2 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
D025040

Remove the 2 C-2 accumulator piston O-rings from the C-2 accumulator piston.


Hide 35111C 20.REMOVE TRANSAXLE HOUSING

U134600

a.

Remove the 14 bolts.


b.

Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

NOTICE:

The differential gear assembly may be accidentally removed when the transaxle housing is removed.



Hide 21.INSPECT INPUT SHAFT END PLAY

U134432

a.

Measure the end play in the axial direction.

End play:

0.37 to 1.29 mm (0.0146 to 0.0508 in.)


If the end play is not as specified, select and replace the thrust needle roller bearing.


Hide 22.REMOVE OIL PUMP ASSEMBLY

U134433

a.

Remove the 7 bolts and the oil pump assembly from the transaxle case.


Hide 23.REMOVE DIFFERENTIAL GEAR ASSEMBLY

C162529

a.

Remove the differential gear assembly from the transaxle case.


Hide 24.REMOVE OVERDRIVE BRAKE GASKET

C067783

a.

Using a screwdriver, remove the 2 overdrive brake gaskets from the transaxle case.


Hide 35701 25.REMOVE INPUT SHAFT ASSEMBLY

C067775

a.

Remove the input shaft assembly from the transaxle case.


Hide 35370A 26.REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING

C067782

a.

Remove the stator shaft thrust needle roller bearing from the input shaft assembly.


Hide 35633 27.REMOVE FRONT CLUTCH CLUTCH DISC

a.
C067851

Using a screwdriver, remove the snap ring.


b.

Remove the forward clutch flange, 4 front clutch clutch discs and the 4 No. 1 clutch plates from the input shaft sub-assembly.


Hide 35603A 28.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D008368E08
1.021,0.625 1.604,0.958 false 0.646,0.521 0.938,0.698 0.292,0.177 10 false SST

Using SST on the No. 1 clutch balancer, compress the forward clutch return spring sub-assembly with a press.

SST
09320-89010  

NOTICE:

Do not compress the return spring excessively.



b.

Using a snap ring expander, remove the snap ring.


c.
D008369

Remove the No. 1 clutch balancer and the forward clutch return spring sub-assembly.


Hide 35612B 29.REMOVE FORWARD CLUTCH PISTON

a.
C067856

Place the input shaft onto the oil pump.


b.

Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump to remove the forward clutch piston.

HINT:

When the piston cannot be removed due to being slanted, either blow the air again with the protruding side pushed or remove the piston using needle-nose pliers with their tips wrapped in protective tape.



Hide 35612C 30.REMOVE FORWARD CLUTCH PISTON O-RING

a.
U134438

Using a screwdriver, remove the forward clutch piston O-ring from the forward clutch piston.


Hide 35712A 31.REMOVE INPUT SHAFT OIL SEAL RING

a.
C067858

Using a screwdriver, remove the input shaft oil seal ring from the input shaft sub-assembly.


Hide 35061C 32.REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

C067776

a.

Remove the forward clutch hub thrust needle roller bearing from the forward clutch hub sub-assembly.


Hide 35708G 33.INSPECT INTERMEDIATE SHAFT ASSEMBLY

D025043

a.

Using a dial indicator, measure the clearance of the intermediate shaft assembly.

Standard clearance:

0.204 to 0.966 mm (0.00803 to 0.03803 in.)


If the clearance is outside the specification, replace the rear clutch drum thrust needle roller bearing.


Hide 35061 34.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C067777

a.

Remove the forward clutch hub sub-assembly from the transaxle case.


Hide 35102 35.REMOVE REAR TRANSAXLE COVER ASSEMBLY

U134434

a.

Remove the 11 bolts.


b.

Tap around the circumference of the rear transaxle cover with a plastic hammer to remove the rear transaxle cover assembly from the transaxle case.


Hide 35102B 36.REMOVE REAR TRANSAXLE COVER PLUG

a.
U134442

Remove the 4 rear transaxle cover plugs from the rear transaxle cover.


b.

Using a screwdriver, remove the 4 O-rings from the 4 rear transaxle cover plugs.


Hide 34603B 37.REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C248586E01
2.682,0.358 2.995,0.515 0.313,0.157 10 SST 1.817,0.753 2.613,0.438 false 2.208,1.779 2.521,1.936 0.313,0.157 10 SST 1.763,2.101 2.173,1.853 false

Using SST, a press and a screwdriver, remove the snap ring.

SST
09387-00070  

NOTICE:

Stop the press when the overdrive brake piston is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove, to prevent the overdrive brake piston from being deformed.



b.
D008358

Remove the overdrive brake return spring sub-assembly from the rear transaxle cover.


Hide 34622B 38.REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C067883

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the rear transaxle cover to remove the 2nd coast and overdrive brake piston.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 34622C 39.REMOVE 2ND COAST AND OVERDRIVE O-RING

a.
C067884

Using a screwdriver, remove the 2 2nd coast and overdrive O-rings from the 2nd coast and overdrive brake piston.


Hide 35617G 40.REMOVE CLUTCH DRUM OIL SEAL RING

a.
U134443

Remove the 3 clutch drum oil seal rings from the rear transaxle cover.


Hide 35102D 41.REMOVE REAR TRANSAXLE COVER NEEDLE ROLLER BEARING

a.
C355253E01
0.458,1.177 0.833,0.969 false 0.146,1.135 0.479,1.323 0.333,0.188 10 false SST 0.552,0.24 0.75,0.438 0.198,0.198 10 false *a 1.75,0.833 1.948,1.031 0.198,0.198 10 false *b

Using SST, remove the rear transaxle cover needle roller bearing from the rear transaxle cover.

Text in Illustration
*a Hold
*b Turn

SST
09387-00041  (09387-01021)


Hide 35145C 42.REMOVE TRANSAXLE CASE GASKET

U134435

a.

Remove the 4 transaxle case gaskets from the transaxle case.


Hide 35651B 43.REMOVE REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

C067780

a.

Using a magnet hand, remove the rear clutch drum thrust needle roller bearing.


Hide 35708G 44.REMOVE INTERMEDIATE SHAFT ASSEMBLY

C067781

a.

Remove the intermediate shaft assembly from the transaxle case.


Hide 35677H 45.REMOVE REVERSE CLUTCH DISC

a.
C067867

Using a screwdriver, remove the snap ring from the intermediate shaft.


b.

Remove the reverse clutch flange, 2 reverse clutch discs and the 2 No. 3 clutch plates from the intermediate shaft.


Hide 35667A 46.REMOVE DIRECT CLUTCH DISC

a.
C067869

Using a screwdriver, remove the snap ring from the intermediate shaft.


b.

Remove the direct clutch flange, 3 direct clutch disc and the 3 rear clutch flanges from the intermediate shaft.


Hide 35604 47.REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C355254E01
2.552,0.76 2.823,0.76 false 2.896,0.667 3.219,0.833 0.323,0.167 10 false SST

Using SST, a press and snap ring expander, remove the snap ring from the direct clutch piston sub-assembly.

SST
09387-00020  


b.

Remove the direct clutch return spring sub-assembly from the intermediate shaft.


Hide 35606A 48.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C067873

Install the intermediate shaft onto the rear transaxle cover.


b.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch piston sub-assembly from the intermediate shaft.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35605A 49.REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.
D025110

Install the intermediate shaft onto the rear transaxle cover.


b.

Put a matchmark on the direct clutch drum sub-assembly in the same position as the cutout of the intermediate shaft.


c.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch drum sub-assembly from the intermediate shaft.

NOTICE:
·

Blowing the air may cause the drum to jump out. When removing the drum, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35606C 50.REMOVE DIRECT CLUTCH PISTON O-RING

a.
U134440

Using a screwdriver, remove the 2 direct clutch piston O-rings from the direct clutch piston sub-assembly.


Hide 35605D 51.REMOVE DIRECT CLUTCH DRUM O-RING

a.
U134441

Using a screwdriver, remove the direct clutch drum O-ring from the direct clutch drum sub-assembly.


Hide 34633 52.REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC

C067785

a.

Remove the 2nd coast and overdrive brake flange, 2 2nd coast and overdrive brake discs and the 2 No. 2 2nd coast and overdrive brake flanges from the transaxle case.


Hide 35605B 53.REMOVE THRUST NEEDLE ROLLER BEARING

C067784

a.

Using a magnet hand, remove the C-2 hub thrust bearing race, thrust needle roller bearing and the No. 3 thrust bearing race from the direct clutch hub.


Hide 35654B 54.REMOVE DIRECT CLUTCH HUB

C068196

a.

Remove the direct clutch hub from the transaxle case.


Hide 35730C 55.REMOVE REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

C067786

a.

Using a magnet hand, remove the rear No. 2 planetary sun gear thrust needle roller bearing from the rear planetary sun gear assembly.


Hide 35730 56.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

C067973

a.

Remove the rear planetary sun gear assembly from the transaxle case.


Hide 35730B 57.REMOVE REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

U134451

a.

Remove the rear planetary sun gear thrust needle roller bearing and the No. 1 planetary carrier thrust washer from the rear planetary sun gear assembly.


Hide 35790A 58.INSPECT 1-WAY CLUTCH ASSEMBLY

D025044E17
2.521,0.823 2.708,1.021 0.188,0.198 10 false *c 1.51,1.438 1.719,1.635 0.208,0.198 10 false *b 1.469,0.198 1.646,0.396 0.177,0.198 10 true *a

a.

Hold the rear planetary sun gear and turn the 1-way clutch assembly.

Text in Illustration
*a Free
*b Lock
*c Hold


b.

Make sure that 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the 1-way clutch assembly does not operate normally, replace it.


Hide 35790A 59.REMOVE 1-WAY CLUTCH ASSEMBLY

C068163

a.

Remove the 1-way clutch assembly and the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.


Hide 34625F 60.REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

C067971

a.

Using a screwdriver, remove the 2nd coast and overdrive brake flange hole snap ring from the transaxle case.


Hide 35682 61.REMOVE 2ND BRAKE BRAKE DISC

C067969

a.

Using a screwdriver, remove the snap ring from the transaxle case.


b.

Remove the 2nd brake brake flange, 3 2nd brake brake discs and the 3 No. 1 2nd brake brake flanges from the transaxle case.


Hide 35626D 62.REMOVE 2ND BRAKE PISTON SLEEVE

C067970

a.

Remove the 2nd brake piston sleeve from the transaxle case.


Hide 35792C 63.INSPECT NO. 2 1-WAY CLUTCH

D025045

a.

Hold the rear planetary gear assembly and turn the No. 2 1-way clutch.

Text in Illustration
V100135

Lock
V100136

Free


b.

Make sure that the No. 2 1-way clutch turns freely counterclockwise and locks when turned clockwise.

If the No. 2 1-way clutch does not operate normally, replace it.


Hide 35760 64.REMOVE REAR PLANETARY GEAR ASSEMBLY

C067967

a.

Using a screwdriver, remove the snap ring from the transaxle case.


b.

Remove the rear planetary gear assembly from the transaxle case.


Hide 35720K 65.REMOVE REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING

C068159

a.

Remove the rear planetary gear thrust needle roller bearing, No. 2 thrust bearing race and the thrust bearing race from the rear planetary gear assembly.


Hide 35792C 66.REMOVE NO. 2 1-WAY CLUTCH

C067966

a.

Remove the No. 2 1-way clutch, 2nd brake piston assembly from the rear planetary gear assembly.


Hide 34365A 67.REMOVE OUTER RACE RETAINER

C067965

a.

Remove the outer race retainer from the No. 2 1-way clutch.


Hide 35608L 68.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
D003796E15
2.25,0.427 2.708,0.271 false 2.74,0.177 3.031,0.354 0.292,0.177 10 false SST

Using SST and a press, remove the snap ring.

SST
09387-00060  


b.
C067862

Remove the 2nd brake piston return spring sub-assembly from the 2nd brake cylinder.


Hide 35624E 69.REMOVE 2ND BRAKE PISTON

a.
C067863

Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.


Hide 35664D 70.REMOVE 2ND BRAKE CYLINDER O-RING

a.
U134439

Using a screwdriver, remove the 2 2nd brake cylinder O-rings from the 2nd brake cylinder.


Hide 35714D 71.REMOVE FRONT PLANETARY SUN GEAR

C068157

a.

Remove the front planetary sun gear and the front planetary gear thrust needle roller bearing from the transaxle case.


Hide 35683 72.REMOVE 1ST AND REVERSE BRAKE DISC

C067963

a.

Using a screwdriver, remove the snap ring from the transaxle case.


b.

Remove the 1st and reverse brake flange, 4 1st and reverse brake discs and the 4 1st and reverse brake plates from the transaxle case.


Hide 35782H 73.REMOVE COUNTER DRIVE GEAR NUT

C067960

a.

Fix the counter drive gear with the parking lock pawl.


b.
C355255E01
1.781,0.99 0.792,0.49 false 0.469,0.375 0.771,0.563 0.302,0.188 10 false SST

Using SST and a hammer, release the counter drive gear lock nut washer.

SST
09930-00010  


c.
D025048E07
0.51,0.76 1.344,1.406 false 0.135,0.604 0.479,0.802 0.344,0.198 10 false SST

Using SST, remove the counter drive gear nut and the counter drive gear lock nut washer.

SST
09387-00121  


Hide 35720G 74.REMOVE PLANETARY GEAR ASSEMBLY

C355256E01
1.802,0.969 2.396,0.969 2.396,0.969 1.938,1.792 false 1.854,1.563 2.385,0.969 false 2.49,0.896 2.781,1.063 0.292,0.167 10 false SST

a.

Using SST and a press, remove the planetary gear assembly from the transaxle case.

SST
09950-60010  (09951-00400, 09951-00320, 09952-06010)
09950-70010  (09951-07100)


Hide 35782C 75.REMOVE COUNTER DRIVE GEAR

C355257

a.

Install the 2 bolts to the counter drive gear.

Recommended service bolt:
Diameter:

10 mm

Pitch:

1.25 mm

Length:

40 to 80 mm (1.575 to 3.150 in.)



b.

Rotate the 2 bolts and remove the counter drive gear.


Hide 35068 76.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D008332E14
1.708,1.427 1.198,1.802 false 0.865,1.719 1.208,1.917 0.344,0.198 10 true SST

a.

Using SST, a press and screwdriver, remove the snap ring from the transaxle case.

SST
09387-00070  


b.

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.


Hide 35623P 77.REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON

C068211

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35623Q 78.REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON O-RING

C067962

a.

Remove the 2 No. 2 1st and reverse brake piston O-rings from the No. 2 1st and reverse brake piston.


Hide 35595 79.REMOVE PARKING LOCK PAWL BRACKET

U134450

a.

Remove the 3 bolts, parking lock cam guide and the parking lock pawl bracket from the transaxle case.


Hide 35506J 80.REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING

C067956

a.

Remove the manual valve lever shaft retainer spring from the manual valve lever shaft.


Hide 35505 81.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

C067954

a.

Using a screwdriver, release and remove the manual valve lever shaft spacer.


b.
C067950

Using a pin punch 3 mm and hammer, drive out the manual valve lever shaft spring pin.


c.

Remove the manual valve lever shaft and manual valve lever sub-assembly.


Hide 35501 82.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

C067951

a.

Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.


Hide 35561 83.REMOVE MANUAL VALVE LEVER SHAFT

C067952

a.

Remove the manual valve lever shaft from the transaxle case.


Hide 35557 84.REMOVE PARKING LOCK PAWL

C067948

a.

Using a screwdriver, remove the parking lock pawl shaft from the transaxle case.


b.

Remove the parking lock pawl torsion spring and the parking lock pawl from the transaxle case.


Hide 41205 85.REMOVE DIFFERENTIAL DRIVE PINION SUB-ASSEMBLY

C068164

a.

Remove the differential drive pinion sub-assembly and the drive pinion thrust bearing LH from the transaxle case.


Hide 41211E 86.REMOVE DIFFERENTIAL DRIVE PINION PLUG

C068188

a.

Using a brass bar and hammer, remove the differential drive pinion plug.


Hide 33326E 87.REMOVE BEARING LOCK PLATE

C067770

a.

Remove the bolt and the bearing lock plate.


Hide 35882A 88.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

C068187

a.

Remove the differential gear lube apply tube from the transaxle housing.


Hide 41211A 89.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C355258E01
0.729,0.396 1,0.604 false 0.448,0.281 0.781,0.458 0.333,0.177 10 false SST 0.406,1.219 0.552,1.417 0.146,0.198 10 false *a 2.656,0.792 2.802,0.99 0.146,0.198 10 false *b

Using SST, remove the front drive pinion front tapered roller bearing from the transaxle housing.

Text in Illustration
*a Hold
*b Turn

SST
09308-10010  


b.

Remove the drive pinion thrust bearing RH from the transaxle housing.


Hide 41211B 90.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C355259E01
1.458,1.292 1.792,0.813 false 2.302,1.906 2.448,2.031 false 1.708,0.635 2.01,0.802 0.302,0.167 10 false SST 0.104,1.292 0.313,1.469 0.208,0.177 10 false *b 2.521,1.958 2.729,2.135 0.208,0.177 10 false *1 2.375,0.354 2.583,0.531 0.208,0.177 10 false *a

Using SST, remove the front drive pinion rear tapered roller bearing from the transaxle case.

Text in Illustration
*1 No. 1 Transaxle Case Plate
*a Hold
*b Turn

SST
09612-65014  (09612-01040)


b.

Remove the No. 1 transaxle case plate from the transaxle case.


Hide 35782E 91.REMOVE COUNTER DRIVE GEAR BEARING

D025049E08
0.708,0.323 1,0.427 false 0.365,0.229 0.688,0.396 0.323,0.167 10 false SST

a.

Remove the 2 counter drive gear bearing inner races and 2 angular balls from the transaxle case.


b.

Using SST, remove the counter drive gear bearing outer race from the transaxle case.

SST
09308-00010  


c.
D025050E08
2.115,0.354 1.49,0.76 true 2.135,0.25 2.448,0.406 0.313,0.156 10 false SST

Using SST, remove the counter drive gear bearing outer race from the transaxle case.

SST
09308-00010  


Hide 35782D 92.REMOVE COUNTER DRIVE GEAR HOLE SNAP RING

C067955

a.

Using a screwdriver, remove the counter drive gear hole snap ring from the transaxle case.


Hide 35506F 93.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C067953

a.

Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.


Hide 31105D 94.REMOVE FRONT TRANSAXLE CASE OIL SEAL

C355260E01
1.469,1.594 0.646,0.458 0.646,0.458 1.552,0.979 false 0.323,0.354 0.604,0.531 0.281,0.177 10 false SST

a.

Using SST and a hammer, remove the front transaxle case oil seal from the transaxle case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07100)


Hide 31105H 95.REMOVE TRANSAXLE CASE OIL SEAL

C355261E01
1.417,1.281 0.792,0.521 0.792,0.521 1.479,0.708 false 0.448,0.427 0.76,0.615 0.313,0.188 10 false SST

a.

Using SST and a hammer, remove the transaxle case oil seal from the transaxle housing.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07100)