Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248166 AUTOMATIC TRANSAXLE UNIT A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C355271

Hide 2.INSPECT DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD

C355277E01
1.948,0.354 1.917,0.177 1.917,0.177 2.083,0.281 false 1.188,0.646 0.521,0.229 false 1,0.833 0.51,0.229 0.51,0.229 1.75,0.594 false 2.542,0.344 3.042,0.49 3.042,0.49 2.792,1.073 false 3.031,0.51 2.823,0.625 false 1.479,1.615 0.698,1.906 0.698,1.906 0.979,1.24 false 1.146,1.531 0.698,1.896 false 2.573,1.427 2.385,1.823 2.385,1.823 1.906,1.646 false 2.292,1.552 2.375,1.813 false 0.375,0.146 0.51,0.302 0.135,0.156 10 false B 2.323,1.917 2.458,2.073 0.135,0.156 10 false A 3.125,0.427 3.26,0.583 0.135,0.156 10 false A 0.552,1.938 0.688,2.094 0.135,0.156 10 false A 1.76,0.063 1.896,0.219 0.135,0.156 10 false A

a.

Coat the differential gear assembly and the front differential case tapered roller bearing with Toyota Genuine ATF WS and install them to the transaxle case.


b.

Install the transaxle housing with the 14 bolts.

Torque:
Bolt A : 29 N*m (300 kgf*cm, 22 ft.*lbf)
Bolt B : 22 N*m (225 kgf*cm, 16 ft.*lbf)


c.
C355278E01
2,0.51 2.542,0.771 true 1.635,0.417 1.969,0.583 0.333,0.167 10 false SST

Using SST and a torque wrench, measure the preload of the differential case tapered roller bearing.

SST
09564-32011  

Standard preload (at Starting):
Bearing Preload
New 0.98 to 1.57 N*m (10.0 to 16.0 kgf*cm 8.7 to 13.9 in.*lbf)
Used 0.49 to 0.78 N*m (5.0 to 8.0 kgf*cm 4.3 to 6.9 in.*lbf)


If the preload is not within the specifications, remove the front differential case rear tapered roller bearing from the transaxle case.

Select a new front differential rear case shim in accordance with the following table.

Front Differential Rear Case Shim Thickness:
Part No. Mark Thickness
mm (in.)
Part No. Mark Thickness
mm (in.)
90564-49001 01 1.90 (0.0748) 90564-49011 11 2.40 (0.0945)
90564-49002 02 1.95 (0.0768) 90564-49012 12 2.45 (0.0965)
90564-49003 03 2.00 (0.0787) 90564-49013 13 2.50 (0.0984)
90564-49004 04 2.05 (0.0807) 90564-49014 14 2.55 (0.1004)
90564-49005 05 2.10 (0.0827) 90564-49015 15 2.60 (0.1024)
90564-49006 06 2.15 (0.0846) 90564-49016 16 2.65 (0.1043)
90564-49007 07 2.20 (0.0866) 90564-49017 17 2.70 (0.1063)
90564-49008 08 2.25 (0.0885) 90564-49018 18 2.75 (0.1082)
90564-49009 09 2.30 (0.0906) 90564-49019 19 2.80 (0.1102)
90564-49010 10 2.35 (0.0925) - - -



Hide 31105H 3.INSTALL TRANSAXLE CASE OIL SEAL

C355345E01
2.021,1.594 2.719,1.281 2.719,1.281 1.906,0.802 false 2.771,1.177 3.083,1.354 0.313,0.177 10 false SST

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.

Using SST and a hammer, drive in the transaxle case oil seal.

SST
09710-20011  (09710-06071)
09950-70010  (09951-07100)

Oil seal drive in depth:

5.4 to 6.4 mm (0.213 to 0.252 in.)



Hide 31105D 4.INSTALL FRONT TRANSAXLE CASE OIL SEAL

C355346E01
1.823,1.438 2.406,1.229 2.406,1.229 1.667,0.844 false 2.479,1.135 2.813,1.313 0.333,0.177 10 false SST

a.

Coat the lip of a new front transaxle case oil seal with MP grease.


b.

Using SST and a hammer, drive in the front transaxle case oil seal.

SST
09554-14010  
09950-70010  (09951-07150)

Oil seal drive in depth:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)



Hide 35506F 5.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

C355347E01
1.427,1.188 0.76,0.813 0.76,0.813 2.052,1.083 true 0.417,0.74 0.708,0.917 0.292,0.177 10 false SST

a.

Coat the lip of a new manual valve lever shaft oil seal with MP grease.


b.

Using SST and a hammer, install a new manual valve lever shaft oil seal.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Oil seal drive in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 35782D 6.INSTALL COUNTER DRIVE GEAR HOLE SNAP RING

C067955

a.

Using a screwdriver, install the counter drive gear hole snap ring to the transaxle case.


Hide 35782E 7.INSTALL COUNTER DRIVE GEAR BEARING

C355348E01
1.823,1.573 2.844,1.781 2.844,1.781 1.625,1.104 true 2.927,1.76 3.229,1.948 0.302,0.188 10 false SST

a.

Using SST and a hammer, install the counter drive gear bearing outer race to the transaxle case.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


b.
C355349E01
1.521,1.521 2.865,1.073 2.865,1.073 1.302,1.073 true 2.938,1 3.271,1.198 0.333,0.198 10 false SST

Using SST and a hammer, install the counter drive gear bearing outer race to the transaxle case.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


c.

Install the 2 counter drive gear bearing inner races and 2 angular balls to the transaxle case.


Hide 41211B 8.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C125250E07
2.427,0.781 2.115,0.979 false 0.917,0.375 1.094,0.552 0.177,0.177 10 false *a 0.917,1.49 1.104,1.667 0.188,0.177 10 false *b 2.458,0.698 2.823,1.031 0.365,0.333 10 false *1

Install the No. 1 transaxle case plate to the transaxle case.

Text in Illustration
*1 No. 1 Transaxle Case Plate
*a Bearing Side
*b Transaxle Case Side


b.
C355350E01
1.625,1.406 2.344,1.521 2.344,1.521 1.51,0.969 true 2.396,1.438 2.708,1.635 0.313,0.198 10 false SST

Using SST and a hammer, install the new front drive pinion rear tapered roller bearing to the transaxle case.

SST
09950-60010  (09951-00610)
09950-70010  (09951-07150)


Hide 41211A 9.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.

Install the drive pinion thrust bearing RH to the transaxle housing.


b.
C355351E01
2.052,1.25 2.469,0.979 2.469,0.979 1.969,0.792 false 2.521,0.875 2.823,1.063 0.302,0.188 10 false SST

Using SST and a press, install a new front drive pinion front tapered roller bearing to the transaxle housing.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35882D 10.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

C068187

a.

Install the differential gear lube apply tube to the transaxle housing.


Hide 33326E 11.INSTALL BEARING LOCK PLATE

C067770

a.

Install the bearing lock plate to the transaxle housing with the bolt.

Torque:
11 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 41211E 12.INSTALL DIFFERENTIAL DRIVE PINION PLUG

D025176E06
1.104,0.833 1.729,0.833 false 0.771,0.729 1.115,0.927 0.344,0.198 10 false SST

a.

Using SST and a plastic hammer, install a new differential drive pinion plug to the differential drive pinion sub-assembly.

SST
09221-25026  (09221-00071)

Standard clearance:

2.5 to 2.6 mm (0.0984 to 0.1023 in.)



Hide 41205 13.INSTALL DIFFERENTIAL DRIVE PINION SUB-ASSEMBLY

C068165

a.

Install the differential drive pinion sub-assembly and the drive pinion thrust bearing LH to the transaxle case.


Hide 35557 14.INSTALL PARKING LOCK PAWL

C067948

a.

Coat the parking lock pawl shaft with Toyota Genuine ATF WS.


b.

Install the parking lock pawl, parking lock pawl shaft torsion spring and the parking lock pawl shaft to the transaxle case.

NOTICE:

Check that the parking lock pawl moves smoothly.



Hide 35561 15.INSTALL MANUAL VALVE LEVER SHAFT

C067952

a.

Install the manual valve lever shaft to the transaxle case.

NOTICE:

Do not damage the oil seal lip.



Hide 35501 16.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

C067951

a.

Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.


Hide 35505 17.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.

Coat the manual valve lever sub-assembly with Toyota Genuine ATF WS.


b.

Install the manual valve lever sub-assembly and a new manual valve lever shaft spacer to the manual valve lever shaft.


c.
C067950

Using a pin punch 3 mm and hammer, drive in the manual valve lever shaft spring pin.


d.
C068175

Turn the manual valve lever shaft spacer and the manual valve lever shaft to align the small hole for locating the staking position in the manual valve lever shaft spacer with the staking position mark on the manual valve lever shaft.


e.

Using a punch, stake the manual valve lever shaft spacer through the small hole.


f.

Check that the manual valve lever shaft spacer does not turn.


Hide 35506J 18.INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING

C067956

a.

Install the manual valve lever shaft retainer spring to the manual valve lever shaft.


Hide 35595 19.INSTALL PARKING LOCK PAWL BRACKET

U134450

a.

Install the parking lock rod sub-assembly, parking lock cam guide and the parking lock pawl bracket to the transaxle case with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35623Q 20.INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON O-RING

C067962

a.

Coat 2 new No. 2 1st and reverse brake piston O-rings with Toyota Genuine ATF WS, and install them to the No. 2 1st and reverse brake piston.

NOTICE:

Do not damage the O-ring.



Hide 35623P 21.INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON

C068210

a.

Coat the No. 2 1st and reverse brake piston with Toyota Genuine ATF WS, and install it to the transaxle case.

NOTICE:

Do not damage the O-ring.



Hide 35068 22.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D008332E15
1.688,1.448 1.198,1.802 false 0.833,1.74 1.177,1.938 0.344,0.198 10 true SST

a.

Install the 1st and reverse brake return spring sub-assembly to the transaxle case.


b.

Using SST, a press and a screwdriver, install the snap ring to the transaxle case.

SST
09387-00070  


Hide 35782C 23.INSTALL COUNTER DRIVE GEAR

C355272E01
1.781,1.396 2.219,1.396 2.219,1.396 1.771,1.906 false 2.438,3 2.75,3.167 2.75,3.167 2.479,3.313 false 2.271,1.302 2.604,1.49 0.333,0.188 10 false SST 2.781,3.094 3.115,3.281 0.333,0.188 10 false SST

a.

Using SST and a press, install the counter drive gear to the transaxle case.

SST
09223-15030  
09527-17011  
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35720G 24.INSTALL PLANETARY GEAR ASSEMBLY

C355273E01
1.771,1.406 2.052,1.406 2.052,1.406 1.833,2.271 false 2.448,3.125 2.688,3.281 2.688,3.281 2.469,3.427 false 2.104,1.344 2.438,1.521 0.333,0.177 10 false SST 2.729,3.208 3.063,3.385 0.333,0.177 10 false SST

a.

Using SST and a press, install the planetary gear assembly to the transaxle case.

SST
09950-60010  (09951-00480)
09223-15030  
09527-17011  
09950-70010  (09951-07150)


Hide 35782H 25.INSTALL COUNTER DRIVE GEAR NUT

C067960

a.

Fix the counter driven gear with the parking lock pawl.


b.
C355352E01
1.281,1.531 0.625,0.469 true 0.292,0.354 0.573,0.552 0.281,0.198 10 false SST

Using SST, install a new counter drive gear lock nut washer and the counter drive gear nut.

SST
09387-00121  

Torque:
280 N*m (2855 kgf*cm, 207 ft.*lbf)


c.
C355353E01
0.531,0.542 1.25,1.542 true 0.219,0.427 0.51,0.625 0.292,0.198 10 false SST

Using SST and a torque wrench, measure the rotating torque while turning the counter drive gear at 60 turns per minute.

SST
09387-00121  

Rotating torque:

0.20 to 0.49 N*m (2 to 5 kgf*cm, 2 to 4 in.*lbf)



d.
C355354E01
1.865,1.135 1.479,0.24 true 1.188,0.125 1.5,0.323 0.313,0.198 10 false SST

Using SST and a hammer, stake the counter drive gear lock nut washer.

SST
09930-00010  


Hide 35683 26.INSTALL 1ST AND REVERSE BRAKE DISC

a.
D025055E10
1.792,0.25 1.979,0.698 false 1.479,0.354 1.667,0.802 false 1.135,0.594 1.302,0.771 0.167,0.177 10 false *3 2.792,1.229 2.99,1.427 0.198,0.198 10 false *4 1.594,0.104 1.781,0.302 0.188,0.198 10 false *1 1.281,0.208 1.469,0.406 0.188,0.198 10 false *2

Install the 4 1st and reverse brake plates, 4 1st and reverse brake discs and the 1st and reverse brake flange to the transaxle case.

Text in Illustration
*1 Snap Ring
*2 1st and Reverse Brake Flange
*3 1st and Reverse Brake Disc
*4 1st and Reverse Brake Plate


b.

Using a screwdriver, install the snap ring to the transaxle case.


Hide 27.INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

C355355E01
1.708,0.958 2.573,0.344 true 2.604,0.24 2.927,0.417 0.323,0.177 10 false SST

a.

Using SST and a dial indicator, measure the 1st and reverse brake clearance while pressing the 1st and reverse brake disc and the 1st and reverse brake plate from the rear side.

SST
09350-36010  (09350-06110)

Pack clearance:

0.806 to 1.206 mm (0.0317 to 0.0475 in.)


NOTICE:

If the clearance is outside the specifications, select a new 1st and reverse brake flange.


HINT:

There are 4 different of flanges available thicknesses.


Flange Thickness:
Part No. Mark Thickness
mm (in.)
35679-52020 - 3.4 (0.134)
35679-52030 1 3.6 (0.142)
35679-52040 2 3.8 (0.150)
35679-52050 3 4.0 (0.157)



b.

Check that the 1st and reverse brake piston moves when compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) is applied to the oil hole.


Hide 35714D 28.INSTALL FRONT PLANETARY SUN GEAR

C068158

a.

Install the front planetary sun gear and the front planetary gear thrust needle roller bearing to the planetary gear assembly.


Hide 35664D 29.INSTALL 2ND BRAKE CYLINDER O-RING

a.
U134439

Coat 2 new 2nd brake cylinder O-rings with Toyota Genuine ATF WS, and install them to the 2nd brake cylinder.

NOTICE:

Do not damage the O-ring.



Hide 35624E 30.INSTALL 2ND BRAKE PISTON

a.
C067866

Coat the 2nd brake piston with Toyota Genuine ATF WS, and install it to the 2nd brake cylinder.

CAUTION:

Do not damage the O-rings when pressing the 2nd brake piston into the 2nd brake cylinder by hand.



Hide 35608L 31.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C067862

Install the 2nd brake piston return spring sub-assembly to the 2nd brake cylinder.


b.
D003796E16
2.25,0.458 2.708,0.271 false 2.74,0.177 3.031,0.354 0.292,0.177 10 false SST

Place SST on the 2nd brake piston return spring sub-assembly, and compress the 2nd brake piston return spring sub-assembly with a press.

SST
09387-00060  


c.

Using a screwdriver, install the snap ring.

NOTICE:

Make sure that the end gap of the snap ring is not aligned with the piston return spring claw.



Hide 34365A 32.INSTALL OUTER RACE RETAINER

C067965

a.

Install the outer race retainer to the No. 2 1-way clutch.


Hide 35792C 33.INSTALL NO. 2 1-WAY CLUTCH

C067966

a.

Install the No. 2 1-way clutch and the 2nd brake piston assembly to the rear planetary gear assembly.


Hide 35720K 34.INSTALL REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING

C068160

a.

Install the No. 2 thrust bearing race, rear planetary gear thrust needle roller bearing and the thrust bearing race to the rear planetary gear assembly.


Hide 35760 35.INSTALL REAR PLANETARY GEAR ASSEMBLY

D025056

a.

Install the rear planetary gear assembly to the transaxle case.


b.

Using a screwdriver, install the snap ring to the transaxle case.


Hide 35792C 36.INSPECT NO. 2 1-WAY CLUTCH

a.
D025045

Check that the rear planetary gear assembly turns freely counterclockwise and locks when turned clockwise.

Text in Illustration
V100135

Lock
V100136

Free

If the No. 2 1-way clutch does not operate normally. replace it.


Hide 35626D 37.INSTALL 2ND BRAKE PISTON SLEEVE

C067970

a.

Install the 2nd brake piston sleeve to the transaxle case.


Hide 35682 38.INSTALL 2ND BRAKE BRAKE DISC

a.
D025097E07
1,0.51 1.167,0.708 0.167,0.198 10 false *1 0.875,1.448 1.073,1.646 0.198,0.198 10 false *2 2.542,1.51 2.781,1.708 0.24,0.198 10 false *3

Install the 3 2nd brake brake discs, 3 No. 1 2nd brake brake flanges and the 2nd brake brake flange to the transaxle case.

Text in Illustration
*1 2nd Brake Brake Flange
*2 2nd Brake Brake Disc
*3 No. 1 2nd Brake Brake Flange


b.

Using a screwdriver, install the snap ring to the transaxle case.


Hide 39.INSPECT PACK CLEARANCE OF 2ND BRAKE

D025098

a.

Using a dial indicator, measure the 2nd brake pack clearance while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).

Pack clearance:

0.847 to 1.247 mm (0.0333 to 0.0491 in.)


NOTICE:

If the clearance is outside the specifications, select a new 2nd brake brake flange.


HINT:

There are 4 different of flanges available thicknesses.


Flange Thickness:
Part No. Mark Thickness
mm (in.)
35678-52020 - 3.0 (0.118)
35678-52030 1 3.2 (0.126)
35678-52040 2 3.4 (0.134)
35678-52050 3 3.6 (0.142)



Hide 34625E 40.INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

C067971

a.

Using a screwdriver, install the 2nd coast and overdrive brake flange hole snap ring to the transaxle case.


Hide 35790A 41.INSTALL 1-WAY CLUTCH ASSEMBLY

C068163

a.

Install the No. 2 planetary carrier thrust washer and the 1-way clutch assembly to the rear planetary sun gear assembly.


Hide 35790A 42.INSPECT 1-WAY CLUTCH ASSEMBLY

a.
D025044E18
2.521,0.708 2.927,0.906 0.406,0.198 10 false *c 1.385,1.354 1.583,1.531 0.198,0.177 10 false *b 1.448,0.177 1.635,0.375 0.188,0.198 10 true *a

Hold the rear planetary sun gear and turn the 1-way clutch assembly and check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

Text in Illustration
*a Free
*b Lock
*c Hold

If the 1-way clutch assembly does not operate normally, replace them.


Hide 35730B 43.INSTALL REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

U134452

a.

Install the rear planetary sub gear thrust needle roller bearing and the No. 1 planetary carrier thrust washer to the rear planetary sun gear assembly.


Hide 35730 44.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

C067973

a.

Install the rear planetary sun gear assembly to the transaxle case.


Hide 35730C 45.INSTALL REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

C068466

a.

Install the rear No. 2 planetary sun gear thrust needle roller bearing to the rear planetary sun gear assembly.


Hide 35654B 46.INSTALL DIRECT CLUTCH HUB

C068196

a.

Install the direct clutch hub to the transaxle case.


Hide 35605B 47.INSTALL THRUST NEEDLE ROLLER BEARING

C068465

a.

Install the No. 3 thrust bearing race, thrust needle roller bearing and the C-2 hub thrust bearing race to the direct clutch hub.


Hide 34633 48.INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC

a.
D025099E11
2.417,0.896 2.854,1.073 0.438,0.177 10 false *1 2.198,1.656 2.531,1.833 0.333,0.177 10 false *3 0.677,1.021 0.854,1.198 0.177,0.177 10 false *2

Install the 2 2nd coast and overdrive brake discs, 2 No. 2 2nd coast and overdrive brake flanges and the 2nd coast and overdrive brake flange to the transaxle case.

Text in Illustration
*1 2nd Coast and Overdrive Brake Flange
*2 2nd Coast and Overdrive Brake Disc
*3 No. 2 2nd Coast and Overdrive Brake Flange


Hide 35605D 49.INSTALL DIRECT CLUTCH DRUM O-RING

a.
U134441

Coat a new direct clutch drum O-ring with Toyota Genuine ATF WS, and install it to the direct clutch drum sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35606C 50.INSTALL DIRECT CLUTCH PISTON O-RING

a.
U134440

Coat 2 new direct clutch piston O-rings with Toyota Genuine ATF WS, and install them to the direct clutch piston sub-assembly.

NOTICE:

Do not damage the O-rings.



Hide 35605A 51.INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.
D025111

Align the cutout in the intermediate shaft with the matchmark on the direct clutch drum sub-assembly and install the direct clutch drum sub-assembly to the intermediate shaft.

NOTICE:

Do not damage the O-ring.



Hide 35606A 52.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C068200

Coat the direct clutch piston sub-assembly with Toyota Genuine ATF WS, and install it to the intermediate shaft.

NOTICE:

Do not damage the O-ring.



Hide 35604 53.INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C355356E02
2.552,0.771 2.844,0.771 false 2.865,0.698 3.188,0.875 0.323,0.177 10 false SST

Install the direct clutch return spring sub-assembly to the direct clutch piston sub-assembly.


b.

Place SST on the direct clutch return spring sub-assembly and compress the springs with a press.

SST
09387-00020  


c.

Using a snap ring expander, install the snap ring to the direct clutch drum sub-assembly.

NOTICE:
·

Stop pressing the press when the spring seat is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring seat from deforming.

·

Do not expand the snap ring excessively.




Hide 35667A 54.INSTALL DIRECT CLUTCH DISC

a.
D025112E09
1.688,0.146 2.188,0.302 false 0.469,0.656 0.656,0.875 0.188,0.219 10 false *3 2.885,0.344 3.052,0.542 0.167,0.198 10 false *2 2.885,0.792 3.042,0.99 0.156,0.198 10 false *4 1.49,0.042 1.677,0.26 0.188,0.219 10 false *1

Coat the direct clutch flange, 3 direct clutch discs and the 3 rear clutch flanges with Toyota Genuine ATF WS, and install them to the intermediate shaft.

Text in Illustration
*1 Snap Ring
*2 Direct Clutch Flange
*3 Direct Clutch Disc
*4 Rear Clutch Flange


b.

Install the snap ring to the intermediate shaft.


Hide 35677H 55.INSTALL REVERSE CLUTCH DISC

a.
C355357E01
2.115,0.25 2.313,0.448 false 1.802,0.458 1.99,0.625 false 1.875,0.729 1.677,0.813 1.677,0.813 1.875,0.927 false 2.625,0.833 2.833,0.917 2.833,0.917 2.615,1 true 1.875,0.146 2.083,0.323 0.208,0.177 10 false *1 1.583,0.354 1.792,0.531 0.208,0.177 10 false *2 1.469,0.74 1.625,0.917 0.156,0.177 10 false *3 2.865,0.833 3.073,1.01 0.208,0.177 10 false *4

Coat the 2 No. 3 clutch plates, 2 reverse clutch discs and the reverse clutch flange with Toyota Genuine ATF WS, and install them to the intermediate shaft.

Text in Illustration
*1 Snap Ring
*2 Reverse Clutch Flange
*3 Reverse Clutch Disc
*4 No. 3 Clutch Plate


b.

Install the snap ring to the intermediate shaft.


Hide 35677H 56.INSPECT PACK CLEARANCE OF REVERSE CLUTCH

a.
D025114

Install the intermediate shaft assembly and the rear clutch drum thrust needle roller bearing to the rear transaxle cover.


b.

Using a dial indicator, measure the reverse clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

Pack clearance:

0.86 to 1.26 mm (0.0339 to 0.0496 in.)


NOTICE:

If the clearance is outside the specifications, select a new reverse clutch flange.


HINT:

There are 4 different of flanges available thicknesses.


Flange Thickness:
Part No. Mark Thickness
mm (in.)
35649-52020 - 3.0 (0.118)
35649-52030 1 3.2 (0.126)
35649-52040 2 3.4 (0.134)
35649-52050 3 3.6 (0.142)



Hide 35667A 57.INSPECT PACK CLEARANCE OF DIRECT CLUTCH

a.
D025115E06
2.667,1.802 2.167,1.365 true 2.594,1.813 2.896,1.969 0.302,0.156 10 true SST

Install the intermediate shaft assembly and the rear clutch drum thrust needle roller bearing to the rear transaxle cover.


b.

Using SST and a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

SST
09350-36010  (09350-06110)

HINT:

The direct and reverse clutch will come out as the compressed air is applied. Therefore, while performing the check, press on the input shaft of the direct and reverse clutch using a stamping machine or the equivalent so that the pressure is not applied to the direct and reverse clutch.


Pack clearance:

0.62 to 1.02 mm (0.0244 to 0.0402 in.)


NOTICE:

If the clearance is outside the specifications, select a new direct clutch flange.


HINT:

There are 4 different of flanges available thicknesses.


Flange Thickness:
Part No. Mark Thickness
mm (in.)
35675-52040 - 3.0 (0.118)
35675-52050 1 3.2 (0.126)
35675-52060 2 3.4 (0.134)
35675-52070 3 3.6 (0.142)



Hide 35708G 58.INSTALL INTERMEDIATE SHAFT ASSEMBLY

C067781

a.

Install the intermediate shaft assembly to the transaxle case.


Hide 59.INSPECT 2ND COAST AND OVERDRIVE BRAKE CLEARANCE

C068205

a.

As shown in the illustration, place a straightedge on the transaxle case and measure the distance between the 2nd coast and overdrive brake flange and straightedge using a vernier caliper. (Dimension A)


b.
C068206

As shown in the illustration, place a straightedge on the 2nd coast and overdrive brake piston and measure the distance between the rear transaxle cover and straightedge using a vernier caliper. (Dimension B)

Calculate the piston stroke value using the following formula. Select a 2nd coast and overdrive brake flange which meets the piston stroke value and install it.

HINT:

Pack clearance = Dimension A - Dimension B


Pack clearance:

2.091 to 2.491 mm (0.0823 to 0.0981 in.)


NOTICE:

If the clearance is outside the specifications, select a new 2nd coast and overdrive brake flange.


HINT:

There are 4 different of flanges available thicknesses.


Flange Thickness:
Part No. Mark Thickness
mm (in.)
34625-52110 4 4.0 (0.158)
34625-52071 5 4.2 (0.165)
34625-52081 6 4.4 (0.173)
34625-52091 7 4.6 (0.181)



Hide 35651B 60.INSTALL REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

C068467

a.

Install the rear clutch drum thrust needle roller bearing to the intermediate shaft assembly.


Hide 35708G 61.INSPECT INTERMEDIATE SHAFT ASSEMBLY

a.

Install the rear transaxle cover with the 11 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


b.
D025043

Using a dial indicator, measure the clearance of the intermediate shaft assembly.

Standard clearance:

0.204 to 0.966 mm (0.00803 to 0.03803 in.)


If the clearance is outside the specifications, replace the rear clutch drum thrust needle roller bearing.


c.

Remove the 11 bolts and the rear transaxle cover.


Hide 35145C 62.INSTALL TRANSAXLE CASE GASKET

U134435

a.

Install 4 new transaxle case gaskets to the transaxle case.


Hide 35102D 63.INSTALL REAR TRANSAXLE COVER NEEDLE ROLLER BEARING

a.
C355358E01
1.135,1.052 0.698,0.406 0.698,0.406 1.104,0.51 false 0.375,0.344 0.667,0.521 0.292,0.177 10 false SST

Coat a new rear transaxle cover needle roller bearing with Toyota Genuine ATF WS.


b.

Using SST and a press, install the rear transaxle cover needle roller bearing to the rear transaxle cover.

SST
09950-60010  (09951-00190, 09952-06010)
09950-70010  (09951-07100)

Standard clearance:

25.2 mm (0.992 in.)



Hide 35617G 64.INSTALL CLUTCH DRUM OIL SEAL RING

a.
D025116E08
2.604,0.188 2.74,0.375 0.135,0.188 10 false A

Compress 3 new clutch drum oil seal rings from both sides to reduce dimension A.

Dimension A:

5.0 mm (0.197 in.)



b.

Coat the 3 clutch drum oil seal rings with Toyota Genuine ATF WS, and install them to the rear transaxle cover.


Hide 34622C 65.INSTALL 2ND COAST AND OVERDRIVE O-RING

a.
C067884

Coat 2 new 2nd coast and overdrive O-rings with Toyota Genuine ATF WS, and install them to the 2nd coast and overdrive brake piston.

NOTICE:

Do not damage the O-ring.



Hide 34622B 66.INSTALL 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C067889

Coat the 2nd coast and overdrive brake piston with Toyota Genuine ATF WS, and install it to the rear transaxle cover.

NOTICE:

Do not damage the O-ring.



Hide 34603B 67.INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
D008358

Install the overdrive brake return spring sub-assembly to the rear transaxle cover.


b.
C248586E01
2.682,0.358 2.995,0.515 0.313,0.157 10 SST 1.817,0.753 2.613,0.438 false 2.208,1.779 2.521,1.936 0.313,0.157 10 SST 1.763,2.101 2.173,1.853 false

Using SST and a press, shorten the overdrive brake return spring sub-assembly, then install the snap ring.

SST
09387-00070  

NOTICE:
·

Stop the press when the overdrive brake piston is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove, to prevent the overdrive brake piston from being deformed.

·

Do not expand the snap ring excessively.




Hide 35102B 68.INSTALL REAR TRANSAXLE COVER PLUG

a.
U134442

Coat 4 new O-rings with Toyota Genuine ATF WS, and install them to the 4 rear transaxle cover plugs.


b.

Install the 4 rear transaxle cover plugs to the rear transaxle cover.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 35102 69.INSTALL REAR TRANSAXLE COVER ASSEMBLY

C068204E05
0.979,0.958 0.51,0.958 false 0.292,0.854 0.479,1.042 0.188,0.188 10 false *a

a.

Apply seal packing to the transaxle case.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




b.
U134434

Install the rear transaxle cover assembly with the 11 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 35061 70.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

C067777

a.

Install the forward clutch hub sub-assembly to the transaxle case.


Hide 35061C 71.INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

C068464

a.

Install the forward clutch hub thrust needle roller bearing to the forward clutch hub sub-assembly.


Hide 35712A 72.INSTALL INPUT SHAFT OIL SEAL RING

a.
C067858

Coat a new input shaft oil seal ring with Toyota Genuine ATF WS, and install it to the input shaft sub-assembly.


Hide 35612C 73.INSTALL FORWARD CLUTCH PISTON O-RING

a.
U134438

Coat a new forward clutch piston O-ring with Toyota Genuine ATF WS, and install it to the forward clutch piston.


Hide 35612B 74.INSTALL FORWARD CLUTCH PISTON

a.
C068199

Install the forward clutch piston to the input shaft sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35603A 75.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C067854

Install the forward clutch return spring sub-assembly and the No. 1 clutch balancer to the input shaft sub-assembly.


b.
D008368E09
1.021,0.625 1.604,0.958 false 0.646,0.521 0.938,0.698 0.292,0.177 10 false SST

Using SST, a press and snap ring expander, install the snap ring to the input shaft sub-assembly.

SST
09320-89010  


Hide 35633 76.INSTALL FRONT CLUTCH CLUTCH DISC

a.
C355359E01
2.365,0.354 2.51,0.531 false 1.969,0.417 2.177,0.615 false 2.052,1.083 1.406,0.406 1.406,0.406 2.052,0.729 false 2.052,0.958 1.417,0.417 1.417,0.417 2.042,0.823 false 2.635,1.021 2.927,0.958 2.927,0.958 2.635,0.896 false 2.625,1.156 2.927,0.958 2.927,0.958 2.604,0.781 false 2.167,0.24 2.354,0.427 0.188,0.188 10 false *1 1.771,0.271 1.938,0.448 0.167,0.177 10 false *2 1.229,0.302 1.417,0.49 0.188,0.188 10 false *3 2.958,0.885 3.146,1.073 0.188,0.188 10 false *4

Install the 4 No. 1 clutch plates, 4 front clutch clutch discs and the forward clutch flange.

Text in Illustration
*1 Snap Ring
*2 Forward Clutch Flange
*3 Front Clutch Clutch Disc
*4 No. 1 Clutch Plate


b.

Using a screwdriver, install the snap ring to the input shaft sub-assembly.


Hide 77.INSPECT PACK CLEARANCE OF FORWARD CLUTCH

a.
C067860

Using a dial indicator, measure the pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

Pack clearance:

1.406 to 1.806 mm (0.0554 to 0.0711 in.)


NOTICE:

If the clearance is outside the specifications, select a new forward clutch flange.


HINT:

There are 4 different of flanges available thicknesses.


Flange Thickness:
Part No. Mark Thickness
mm (in.)
35635-52050 - 3.0 (0.118)
35635-52060 1 3.2 (0.126)
35635-52070 2 3.4 (0.134)
35635-52080 3 3.6 (0.142)



Hide 35370A 78.INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING

C067938

a.

Install the stator shaft thrust needle roller bearing to the input shaft assembly.


Hide 35701 79.INSTALL INPUT SHAFT ASSEMBLY

C067775

a.

Install the input shaft assembly to the transaxle case.


Hide 80.INSTALL OVERDRIVE BRAKE GASKET

C067783

a.

Install 2 new overdrive brake gaskets to the transaxle case.


Hide 81.INSTALL DIFFERENTIAL GEAR ASSEMBLY

C162529

a.

Install the differential gear assembly to the transaxle case.


Hide 82.INSTALL OIL PUMP ASSEMBLY

a.
C355309

Install the oil pump assembly to the transaxle case with the 7 bolts.

Torque:
22 N*m (225 kgf*cm, 16 ft.*lbf)


Hide 35701 83.INSPECT INPUT SHAFT ASSEMBLY

C068186

a.

Make sure that the input shaft turns smoothly.

If the input shaft assembly does not operate normally, replace it.


Hide 84.INSPECT INPUT SHAFT END PLAY

U134432

a.

Measure the end play in the axial direction.

End play:

0.37 to 1.29 mm (0.0146 to 0.0508 in.)


If the end play is not as specified, replace the thrust needle roller bearing.


Hide 35111C 85.INSTALL TRANSAXLE HOUSING

C081344E05
2.667,0.563 2.885,0.375 false 2.906,0.281 3.26,0.427 0.354,0.146 10 false *a

a.

Apply seal packing to the transaxle case.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




b.
A057108

Apply adhesive to 2 or 3 threads on the end of the 3 bolts B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
C355360E01
1.177,0.677 0.5,0.292 false 0.969,0.865 0.49,0.281 0.49,0.281 1.698,0.615 true 1.458,1.646 0.479,1.781 0.479,1.781 0.906,1.26 true 1.083,1.552 0.5,1.76 false 2.563,1.469 2.469,1.917 2.469,1.917 1.885,1.667 true 2.25,1.604 2.469,1.906 false 2.25,1.594 2.458,1.896 false 1.927,0.375 1.906,0.208 1.906,0.208 2.073,0.302 true 2.531,0.333 2.917,0.292 2.917,0.292 2.802,0.667 true 0.323,0.135 0.479,0.333 0.156,0.198 10 false B 2.521,1.927 2.677,2.125 0.156,0.198 10 false A 2.99,0.167 3.146,0.365 0.156,0.198 10 false A 1.781,0.052 1.938,0.25 0.156,0.198 10 false A 0.344,1.708 0.5,1.906 0.156,0.198 10 false A

Install the transaxle housing with the 14 bolts.

Torque:
Bolt A : 29 N*m (300 kgf*cm, 22 ft.*lbf)
Bolt B : 22 N*m (225 kgf*cm, 16 ft.*lbf)


Hide 35425A 86.INSTALL C-2 ACCUMULATOR PISTON

D025040

a.

Coat 2 new C-2 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the C-2 accumulator piston.

NOTICE:

Do not damage the O-ring.



b.
C068839

Install the C-2 accumulator piston compression spring and the C-2 accumulator piston.

Accumulator Spring:
Spring Free Length/
Outer Diameter mm (in.)
Color
C-2 66.90 (2.6339)
17.20 (0.6772)
-



Hide 35426D 87.INSTALL C-3 ACCUMULATOR PISTON

D025039

a.

Coat 2 new C-3 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the C-3 accumulator piston.

NOTICE:

Do not damage the O-ring.



b.
C068840

Install the C-3 accumulator piston compression spring and the C-3 accumulator piston.

Accumulator Spring:
Spring Free Length/
Outer Diameter mm (in.)
Color
C-3 80.20 (3.1575)
18.70 (0.7362)
Blue



Hide 35423 88.INSTALL B-2 ACCUMULATOR PISTON

D025038

a.

Coat 2 new B-2 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the B-2 accumulator piston.

NOTICE:

Do not damage the O-ring.



b.
C068841

Install the B-2 accumulator piston compression spring and the B-2 accumulator piston.

Accumulator Spring:
Spring Free Length/
Outer Diameter mm (in.)
Color
B-2 66.90 (2.6339)
15.50 (0.6102)
Green



Hide 35251 89.INSTALL CHECK BALL BODY

C067767

a.

Install the check ball body compression spring and the check ball body to the transaxle case.


Hide 35159 90.INSTALL BRAKE DRUM GASKET

U134430

a.

Install a new brake drum gasket to the transaxle case.


Hide 35145C 91.INSTALL TRANSAXLE CASE GASKET

C067758

a.

Coat a new transaxle case gasket with Toyota Genuine ATF WS, and install it to the transaxle case.


Hide 35149B 92.INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

C067757

a.

Coat a new transaxle case 2nd brake gasket with Toyota Genuine ATF WS, and install it to the transaxle case.


Hide 82125J 93.INSTALL TRANSMISSION WIRE

C067760

a.

Coat a new O-ring with Toyota Genuine ATF WS, and install it to the transmission wire.


b.
D025102

Pass the transmission wire through the transaxle case.


c.
C062929

Install the transmission wire with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35410 94.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Align the groove of the manual valve with the pin of the manual valve lever.


b.
C093940E21
0.917,1.594 0.677,1.75 false 1.073,1.385 0.542,1.521 false 0.854,1.354 0.542,1.521 false 0.823,1.073 0.542,0.927 false 0.854,0.854 0.542,0.927 false 1.063,1.094 0.719,0.323 false 1.073,0.823 0.719,0.323 false 1.156,0.375 1.156,0.188 false 1.385,0.438 2.448,0.125 false 1.646,0.427 2.448,0.125 false 2.042,0.438 2.427,0.125 false 2.354,0.875 2.781,0.875 false 1.917,0.479 2.781,0.875 false 0.531,1.688 0.656,1.885 0.125,0.198 10 false B 0.385,1.427 0.51,1.625 0.125,0.198 10 false A 0.396,0.875 0.531,1.073 0.135,0.198 10 false D 0.563,0.208 0.698,0.406 0.135,0.198 10 false C 1.104,0.01 1.229,0.208 0.125,0.198 10 false A 2.479,0.021 2.604,0.219 0.125,0.198 10 false B 2.823,0.75 2.948,0.948 0.125,0.198 10 false A

Temporarily install the transmission valve body assembly with the 13 bolts.

Bolt Length
Bolt Bolt Length
A 32 mm (1.260 in.)
B 20 mm (0.787 in.)
C 55 mm (2.165 in.)
D 45 mm (1.772 in.)


c.
C093939E46
2.25,0.604 2.635,0.375 false 2.25,1.052 2.667,0.854 false 2.24,1.167 2.656,1.167 false 2.219,1.323 2.604,1.5 false 2.667,0.26 3.177,0.625 0.51,0.365 10 false *1 2.698,0.729 2.823,0.927 0.125,0.198 10 false A 2.688,1.052 3.146,1.25 0.458,0.198 10 false *2 2.646,1.406 2.771,1.604 0.125,0.198 10 false B

Temporarily install the manual detent spring and the manual detent spring cover with the 2 bolts.

Text in Illustration
*1 Manual Detent Spring
*2 Manual Detent Spring Cover

Bolt Length
Bolt Bolt Length
A 14 mm (0.551 in.)
B 45 mm (1.772 in.)


d.

Check that the manual valve lever comes into contact with the center of the roller at the tip of the manual detent spring.


e.

Tighten the 15 bolts.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)


f.
C355361

Connect the 5 solenoid connectors.


g.

Install the transmission wire with the lock plate and bolt.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)

Bolt length:

55 mm (2.165 in.)



Hide 35330 95.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

U134876

a.

Coat a new oil strainer gasket with Toyota Genuine ATF WS, and install it to the valve body oil strainer assembly.


b.
C062685

Install the valve body oil strainer assembly to the with the 3 bolts.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)


Hide 35106D 96.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

U134466

a.

Install the 2 oil cleaner magnets to the automatic transaxle oil pan sub-assembly.


b.
A057108

Apply adhesive to 2 or 3 threads on the end of the 2 bolts A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
C062684E15
2.344,0.646 2.781,0.646 true 2.344,0.958 2.635,0.958 2.635,0.958 2.635,0.656 true 0.885,0.219 0.885,0.063 0.885,0.063 2.542,0.063 true 1.146,0.229 1.146,0.073 true 1.438,0.073 1.438,0.229 true 1.729,0.229 1.729,0.063 true 2.021,0.229 2.021,0.073 true 0.677,0.438 0.219,0.438 0.219,0.438 0.219,1.813 true 0.521,0.74 0.219,0.74 true 0.531,1.063 0.229,1.063 true 0.51,1.354 0.219,1.354 true 0.563,1.667 0.229,1.667 true 2.292,0.302 2.292,0.063 true 0.875,1.802 0.875,2 0.875,2 2.49,2 true 2.271,1.292 2.271,1.99 true 2.073,1.531 2.073,2 true 1.844,1.75 1.844,2 true 1.51,1.792 1.51,2 true 1.198,1.792 1.198,1.99 true 2.854,0.573 2.979,0.74 0.125,0.167 10 false A 2.615,0 2.74,0.167 0.125,0.167 10 false B 0.188,1.833 0.313,2 0.125,0.167 10 false B 2.542,1.906 2.667,2.073 0.125,0.167 10 true B

Install the automatic transaxle oil pan sub-assembly and a new automatic transaxle oil pan gasket with the 19 bolts.

Torque:
Bolt A : 7.4 N*m (75 kgf*cm, 65 in.*lbf)
Bolt B : 7.8 N*m (80 kgf*cm, 69 in.*lbf)


d.

Install the drain plug and a new gasket to the automatic transaxle oil pan sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 35104B 97.INSTALL BREATHER PLUG

a.

Install the breather plug to the transaxle case.


Hide 35012 98.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

C067752

a.

Install the transmission breather hose sub-assembly to the breather plug.


Hide 35104Q 99.INSTALL NO. 1 TRANSAXLE CASE PLUG

C067754

a.

Coat 5 new O-rings with Toyota Genuine ATF WS, and install them to the No. 1 transaxle case plugs.


b.

Install the 4 No. 1 transaxle case plugs to the transaxle housing and the transaxle case.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


c.
C067755

Install the No. 1 transaxle case plug to the transaxle case.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 32921C 100.INSTALL OIL COOLER TUBE UNION

U134877

a.

Coat 2 new O-rings with Toyota Genuine ATF WS, and install them to the 2 oil cooler tube unions.


b.

Install the 2 oil cooler tube unions to the transaxle case.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 89413B 101.INSTALL TRANSMISSION REVOLUTION SENSOR

U134429

a.

Coat a new O-ring with Toyota Genuine ATF WS, and install it to the transmission revolution sensor.


b.

Install the transmission revolution sensor to the transaxle case with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 84540 102.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

U134502

a.

Install the park/neutral position switch assembly.


b.

Temporarily install the 2 bolts.


c.

Replace the lock plate with a new one and install the nut, lock plate and washer.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


d.

Temporarily install the transmission control shaft lever.


e.
C117103

Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.


f.

Remove the transmission control shaft lever.


g.
C355362E01
1.552,0.896 0.573,0.542 true 1.604,1.146 0.646,1.188 true 0.385,0.448 0.573,0.646 0.188,0.198 10 false *a 0.427,1.083 0.615,1.281 0.188,0.198 10 false *b

Align the groove with the neutral basic line.

Text in Illustration
*a Neutral Basic Line
*b Groove


h.

Hold the switch in this position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


i.
C117105

Using a screwdriver, stake the nut with the lock plate.


Hide 35572A 103.INSTALL TRANSMISSION CONTROL SHAFT LEVER

a.
C117101

Install the transmission control shaft lever with the nut and washer.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)