35370
1.INSPECT STATOR SHAFT ASSEMBLY
Using a caliper gauge, measure the inside diameter of the stator shaft bushings.
21.500 to 21.526 mm (0.846 to 0.847 in.)
21.526 mm (0.847 in.)
If the inside diameter is greater than the maximum, replace the stator shaft assembly.
Install the input shaft assembly onto the stator shaft assembly and check that the input shaft assembly turns smoothly.
Replace the stator shaft assembly with a new one if it moves roughly or makes unusual noise.
Inspect the input shaft's contact surface with the bearing when replacing, and replace the input shaft with a new one if any damage or discoloration is found.
35301
2.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY
Using a caliper gauge, measure the inside diameter of the front oil pump body bushing.
38.113 to 38.138 mm (1.5005 to 1.5015 in.)
38.138 mm (1.5015 in.)
If the inside diameter is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.
3.INSPECT OIL PUMP GEAR CLEARANCE
Using a feeler gauge, measure the clearance between the tips of the front oil pump driven gear teeth and the front oil pump drive gear teeth.
0.07 to 0.15 mm (0.00276 to 0.00591 in.)
0.15 mm (0.00591 in.)
If the tip clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.
Push the front oil pump driven gear to one side of the body. Using a feeler gauge, measure the clearance.
0.10 to 0.15 mm (0.00394 to 0.00591 in.)
0.15 mm (0.00591 in.)
If the body clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.
Using a steel straightedge and feeler gauge, measure the side clearance of both gears.
0.02 to 0.05 mm (0.000787 to 0.00197 in.)
0.05 mm (0.00197 in.)
If the side clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.
| Part No. | Mark | Thickness
mm (in.) |
|---|---|---|
| 35321-52060 | 1 | 9.44 to 9.45 (0.3709 to 0.3713) |
| 35321-52070 | 2 | 9.45 to 9.46 (0.3713 to 0.3717) |
| 35321-52080 | 3 | 9.46 to 9.47 (0.3717 to 0.3721) |
| 35321-52090 | 4 | 9.47 to 9.48 (0.3721 to 0.3725) |
| 35321-52100 | 5 | 9.48 to 9.49 (0.3725 to 0.3729) |
| Part No. | Mark | Thickness
mm (in.) |
|---|---|---|
| 35322-52060 | 1 | 9.44 to 9.45 (0.3709 to 0.3713) |
| 35322-52070 | 2 | 9.45 to 9.46 (0.3713 to 0.3717) |
| 35322-52080 | 3 | 9.46 to 9.47 (0.3717 to 0.3721) |
| 35322-52090 | 4 | 9.47 to 9.48 (0.3721 to 0.3725) |
| 35322-52100 | 5 | 9.48 to 9.49 (0.3725 to 0.3729) |