Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2011.08–2016.09
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248170 AUTOMATIC TRANSAXLE SYSTEM C

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the ECM.

The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1, and the ECM calculates the fluid temperature based on the voltage signal.

HINT:
·

The ATF temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.

·

When the ATF temperature sensor is normal, the transmission locks up in 4th gear with the shift lever in D and in 3rd gear with the shift lever in 3rd.



DTC No. DTC Detection Condition Trouble Area
P0712 ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more (1 trip detection logic).
·

Wire harness or connector

·

Transmission wire (ATF temperature sensor)

·

ECM


P0713 Following condition continues for 0.5 seconds or more (1 trip detection logic)
ATF temperature sensor resistance is more than 156 kΩ after 15 minutes or more after start engine.
·

Wire harness or connector

·

Transmission wire (ATF temperature sensor)

·

ECM



MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM turns on the MIL and stores the DTC.

*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:

The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM

C243250E02
0.955,2.163 1.232,2.315 0.277,0.152 10 B74 0.955,2.33 2.143,2.478 1.188,0.147 10 Transmission Wire 1.208,0.887 2.315,1.209 1.107,0.322 10 ATF Temperature Sensor 2.43,0.805 2.757,0.957 0.327,0.152 10 THO 2.783,0.615 2.899,0.781 0.116,0.165 10 1 2.548,1.842 2.740,1.993 0.192,0.152 10 E2 2.783,1.656 2.895,1.813 0.111,0.156 10 6 5.38,0.722 5.652,0.860 0.273,0.138 10 B84 5.431,0.547 5.605,0.690 0.174,0.143 10 72 5.698,0.719 6.092,0.857 0.394,0.138 10 THO1 5.38,1.749 5.652,1.887 0.273,0.138 10 B84 5.431,1.575 5.605,1.717 0.174,0.143 10 95 5.698,1.747 6.137,1.885 0.439,0.138 10 ETHO 5.929,2.167 6.269,2.306 0.340,0.138 10 ECM

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


g.

In accordance with the display on the tester, read the Data List.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
·

Approximately 80°C (176°F): After Stall Test

·

Equal to ambient temperature when cold soak


If value is -40°C (-40°F) or 150°C (302°F) or more, ATF temperature sensor circuit is open or short.

HINT:

When DTC P0712 is output and the intelligent tester reading is 150°C (302°F) or more, there is a short circuit.

When DTC P0713 is output and the intelligent tester reading is -40°C (-40°F), there is an open circuit.

Measure the resistance between terminal THO1 and the body ground.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or more Short circuit


HINT:

If a circuit related to the ATF (Automatic Transmission Fluid) temperature sensor becomes open, P0713 is immediately set (within 0.5 seconds).




PROCEDURE

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
C229166E15
2.716,0.683 3.115,0.842 0.398,0.158 10 THO 2.716,1.527 2.944,1.688 0.227,0.161 10 E2 2.307,0.951 2.676,0.773 false 2.274,1.24 2.656,1.595 false 0.059,0.028 0.256,0.192 0.197,0.164 10 *a

a.

Disconnect the transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 6 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground Always 10 kΩ or higher
6 (E2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)

HINT:

If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may be affected.


Standard Resistance:
ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
U158332E01
1.482,0.254 1.785,0.421 0.303,0.167 10 B84 0.048,0.027 0.258,0.210 0.210,0.182 10 *a 1.691,1.798 2.089,1.948 0.398,0.150 10 THO1 1.296,1.235 1.938,1.77 false 0.454,1.798 0.881,1.948 0.427,0.150 10 ETHO 1.296,1.321 0.701,1.77 false

a.

Connect the transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B84-72 (THO1) - B84-95 (ETHO) Always 79 Ω to 156 kΩ
B84-72 (THO1) - Body ground Always 10 kΩ or higher
B84-95 (ETHO) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR